B&R Automation My First Motion Program Part 1
ฝัง
- เผยแพร่เมื่อ 26 ส.ค. 2024
- Hello Everyone,
Today I want to show you hoe to make your first motion control program in Automation Studio and then actually spin a servo motor! A few highlights that I talk about are the B&R ACOPOS P3 servo drives that can have up to 3-Axis in a very small footprint (www.br-automat.... I also show how easy it is to implement mapp Motion for this project (www.br-automat.... I hope this video gives you some good ideas on your next automation project!
Regards,
Brent Johnson
![ฮักเทื่อสุดท้าย - บอย ศิริชัย [OFFICIAL MV]](http://i.ytimg.com/vi/-1PoPoQ-B-k/mqdefault.jpg)
Great Information Johnson and please make a video Acopos Drive works with Torque to start and stop the motor once the torque is achieved. Thanks for the great videos.
This is a great work, very useful and thanks for it, indeed I am working on it , greetings.
The information you give is very useful.
Please teach us how to create a Cam in Automation studio.
Good
Hi, your videos are very helpful. Could you please make a video on how to program a 3-axis gantry with Virtual Motion Control (for people who don't have hardware)?
Thanks for the feedback! I will consider that as a future topic!
My friend I'm doing the first test as shown in the video. The next day when I went to test without changing anything the Ax1 led was flashing green. According to the manual, I checked the Enable contact pins and I checked the connections. But I can no longer work while the led is blinking.
+++!
Good night. Are you about the RUC? there use to upload of variables! This is correct? Thanks
hello dear, i need your help. i have B &R power panel 4pp065.0571. but its restarting itself again and again. i want to replace its panel but i am worry how i will copy the exisintg software in new panel. although I have a 512MB card installed with it. Can i copy a software from that drive
Hello, how do I get this program? is there any demo, to run small tests?
hola amigo tengo un acopos 100d lo puedo usar con arduino?y match3?
Hello Mr. Brent. Would you please help me with a simple start and stop project to run an induction motor with an Acopos 1045 drive. Thank you.
Hi, can i run b&r servo drive with third party motor . Help me plzz
Good morning, how can I add an 8AC112.60-1 card to the project?
How long
I need to a licence or crack for automation stiodo, any help?
sir can you explain how to add image?
How to use new CF card make a backup and bottable
Hi sir
I reset may X20CP3586 and now I am facing Run Time issue project is in B4. 90 and PLC is in Boot Mode and shows Ar version J4.03
How to fix it
Can you please help me ?
in the project menu you can change runtimes choose a proper one or install diffrent ones which are suitable for your case, for extra help ask at your b&r vendor which runtime is recommended and works for your case.
How to upload project file from PLC ?
Hello, it is not possible to upload a project from a B&R PLC. You will need to contact the original person who created the project to get it.
Hanzhen harmonic drive gear , robot arm gear , joint acurator , over 30 years experience
Hello Taoufiq,
You do have to get a license for Automation Studio. Check out this TH-cam video I created on how to get the software downloaded:
th-cam.com/video/ElXEVbMKMlc/w-d-xo.html
Once you have it downloaded you will need to go to this B&R website to register for your 90 day free trial:
www.br-automation.com/en-us/service/software-registration/
I would suggest getting in touch with your local B&R office to get more information.
Good Luck!