Hi Vladimir. Can head gaskets can be changed without pulling engine off? We have a 3.0 V6 2013 XJ here in our shop. It has a consumption leaking and bad start and overheating problems.
Hi , maybe you can change head gaskets, but I never tried it before. My recommendation is to take off the engine and change rear main seal and valve seals.
Hi i have one in my workshop that look exactly like your engine Jaguar 2010 , i am following your timing description but i want to ask if your car started after you finish coupling
Hi, you need to make sure that gas comes and there is a spark, then double-check yourself that the labels on the chain are correctly set, you also need to check the compression in the cylinders.
Да я в курсе, поставлю в верхнюю мёртвую точкуколенвал, затем просто не знаю ещё как правильно распределительные валы выставить, там сзади на них есть метки которые должны смотреть вниз и вырез должен быть горизонтально, просто с зеркалом прийдётся это делать если двигатель не вытаскивать?
Зная эту систему зажигания и не имея нужного инструмента я бы сделал так: выставил коленвал в нужном месте ,затем выставил бы валы как на видео и при помощи меток на цепи выстовил нужные мне метки, НЕ ципляясь к тому чтобы валы с зади были идеально точно , только соблюсти чтобы с сзади на валах нужные метки стояли вниз.
Hello Vladimir. I am from India. I have an Jaguar XF 2013 4cylinder petrol engine car. Recently I changed my timing tensioner pulley. I have fitted everything my car does crank but it doesn’t starts. Does it has any timing kit. Can you even provide me your email address as well
hi, I think that you need a special tool for your engine, since I didn’t do such engines when, we don’t have such 4 cylinders, but when I made a jaguar 6 cylinders and 8 cylinders, the special tool was different from each other
i need help the position of the tappet i lost the order they are all different. 5.0 SC.... can you help me with some plan
greetings where are your workshop located?
South Carolina
when the crankshaft bench of that engine is torqued, and the connecting rods, if you have the data, I thank you
Hi Vladimir.
Can head gaskets can be changed without pulling engine off? We have a 3.0 V6 2013 XJ here in our shop. It has a consumption leaking and bad start and overheating problems.
Hi , maybe you can change head gaskets, but I never tried it before. My recommendation is to take off the engine and change rear main seal and valve seals.
Jo flywheel side wala tool hai to flywheel me sare hole ek jeaise hai
Hey bud...I have a 2010 xkr. Do I need pull supercharger to change valve cover gasket?
Thanks!
hello, yes you need to remove the super charger and gas injectors to change the gaskets .
Hi i have one in my workshop that look exactly like your engine Jaguar 2010 , i am following your timing description but i want to ask if your car started after you finish coupling
Yes, of course, I myself rode it.
What's the problem ?
@@vladimir.luxurycars i have jaguar with 5.0l v8 engine i am working on the timing but the vehicle refuse to start
@@vladimir.luxurycars 2010 jaguar
Hi, you need to make sure that gas comes and there is a spark, then double-check yourself that the labels on the chain are correctly set, you also need to check the compression in the cylinders.
What is the procedure to set the timming on the gas pump cam. Nobody explains it anywhere
Hi , I'm have this video for the timing on the gas pump
Timing Mark's 2013 Jaguar XJ 5.0 liter
Vladimir H. Thank you
Привет, как можно с вами связаться?
vovcik.h@mail.ru
Alguien sabe como ban los pistones del jaguar 2014 3.0
English please
Владимир, я менял натяжители и сдвинулись муфты, как выставить валы на головке ровно? сзади горизонтальные прорезы для этого?
Да , туда вставляется специальный держатель валов, (Special tool) .
Но для этого нужно выставить коленвал в правильную метку . Но это всего лишь держатели валов , на цепи и на валах есть заводские метки .
Да я в курсе, поставлю в верхнюю мёртвую точкуколенвал, затем просто не знаю ещё как правильно распределительные валы выставить, там сзади на них есть метки которые должны смотреть вниз и вырез должен быть горизонтально, просто с зеркалом прийдётся это делать если двигатель не вытаскивать?
Зная эту систему зажигания и не имея нужного инструмента я бы сделал так: выставил коленвал в нужном месте ,затем выставил бы валы как на видео и при помощи меток на цепи выстовил нужные мне метки, НЕ ципляясь к тому чтобы валы с зади были идеально точно , только соблюсти чтобы с сзади на валах нужные метки стояли вниз.
Спасибо за совет! Завтра буду ковыряться. 2012 Land Rover Lr4 с таким же мотором, менял цепи и натяжители с башмаками.
What song is that
this is a Russian song, I listened to it on (svobodnoe radio)
Hello Vladimir. I am from India. I have an Jaguar XF 2013 4cylinder petrol engine car. Recently I changed my timing tensioner pulley. I have fitted everything my car does crank but it doesn’t starts. Does it has any timing kit. Can you even provide me your email address as well
hi, I think that you need a special tool for your engine, since I didn’t do such engines when, we don’t have such 4 cylinders, but when I made a jaguar 6 cylinders and 8 cylinders, the special tool was different from each other
I also think that you had a bad mark, camshaft and crankshaft.