The original line has a check valve to keep the oil from draining back out of the cooler into the transmission. Two purposes for the check valve it slows the oil circulation down so it can cool properly as it goes through the cooler. Number two without the check valve the oil drains into the transmission and when you start the truck you hesitate to fill the cooler back up so it shifts properly. Without the check valve and overfills the transmission when the cooler drains back and the very top wiring harness in the transmission usually leaks fluid onto the floor.
Wow the timing of this video, couldn’t have been any better! I was just looking at this kit on your website earlier today! My trans lines have been leaking!
@@pddofficial when you have honest down to earth people working for you it’s makes it easy to support PDD. I have purchased many items from you and I’m looking forward to buying many more. Thanks!
Love the content and the trash talking from the wire fire gang to the mechanical mafia. Looking forward to the rebuttal from Will and Todd. Seems like both their daily trucks are wire fire now.
Where do I get push locks that’ll work on the stock trans cooler? I have lines just shoved on the end with double hose clamps, had to use hydraulic lines off the heat exchanger on the block then connect push locks to those. This kit would’ve been nice to have 2 years ago.
Look like I’m ordering a kit for my 2003 Dodge Ram 2500 4x4 diesel(5.9) cause I just had a universal joint break and then my driveshaft screw up my trans lines. New Sub here!
Will this fix the leak I have coming from the two lines going to the inter cooler, two lines are on the driver side, I mistaken the leak for a steering box issue replaced that and it still leaks
Brother I just did the same thing, "good" excuse to get a red head which is FKIN AMAZING, but yeah, went to go clean everything up with the inner fender out and found the return to trans line puking from the air cooler.
What would you guys recommend for a pump to pump 85w140 gear oil gear oil to oil cooler....we have a old Doug Nash overdrive behind a C6 and the Doug Nash over heats in overdrive running empty at about the 100-150mi mark
That kit is just what I need. What are the length of the lines? I am thinking of bypassing my exchanger and am wondering if the two large lines will work.
hey with this kit when i select the 03-07 48re will it still have the lines for the heat exchanger? I see there's only one option that says heat exchanger?
Could someone please send a link showing me what a 4 way hydraulic wrench with 2 different angles as recommended in this video looks like? I tried to google but no info. Thx
Do you have just the quick connect fitting for sale I can buy for the trans cooler side for my 05 that are push lock style that I can just put a hose clamp on ?
They are a perfect fit. You will need a heat gun to get the line on. I have this kit on my 03 2500 with a 47 re. Make sure you also get the transmission line re moral tool.
The original line has a check valve to keep the oil from draining back out of the cooler into the transmission. Two purposes for the check valve it slows the oil circulation down so it can cool properly as it goes through the cooler. Number two without the check valve the oil drains into the transmission and when you start the truck you hesitate to fill the cooler back up so it shifts properly. Without the check valve and overfills the transmission when the cooler drains back and the very top wiring harness in the transmission usually leaks fluid onto the floor.
Where is the check valve?
Wow the timing of this video, couldn’t have been any better! I was just looking at this kit on your website earlier today! My trans lines have been leaking!
The hardest part about the installation is not spilling any transmission fluid lol. very easy and simple installation besides that.
Love the 3rd gen content. Would love more 3rd gen 6.7 stuff however!
This kit is a must-have for these trucks and others. Great video
Thanks 👍
More 3rd gen videos please!
Awesome video!
We agree!
I am liking the 3rd gen stuff they are my favorite body style haha
I have this kit on my 03 with a 47 re and it’s great!
Glad it worked well for you! Thanks for the support!
@@pddofficial when you have honest down to earth people working for you it’s makes it easy to support PDD. I have purchased many items from you and I’m looking forward to buying many more. Thanks!
Love the content and the trash talking from the wire fire gang to the mechanical mafia. Looking forward to the rebuttal from Will and Todd. Seems like both their daily trucks are wire fire now.
Nice looking kit ! Great video as usual 😬🤘🏻
Is there a kit if you have deleted the heat exchanger?
Just installed this hard part was the old quick connect had to cut on off very carefully with a grinder but other than that very easy just dirty lol
Where do I get push locks that’ll work on the stock trans cooler? I have lines just shoved on the end with double hose clamps, had to use hydraulic lines off the heat exchanger on the block then connect push locks to those. This kit would’ve been nice to have 2 years ago.
Look like I’m ordering a kit for my 2003 Dodge Ram 2500 4x4 diesel(5.9) cause I just had a universal joint break and then my driveshaft screw up my trans lines. New Sub here!
What would you need to do if you end up cracking the case putting the fitting in?
Will this fix the leak I have coming from the two lines going to the inter cooler, two lines are on the driver side, I mistaken the leak for a steering box issue replaced that and it still leaks
Brother I just did the same thing, "good" excuse to get a red head which is FKIN AMAZING, but yeah, went to go clean everything up with the inner fender out and found the return to trans line puking from the air cooler.
Yes it will
Does the loctite 545 stay wet or does it hard within the treads?? Thanks in advance
It hardens
Does this kit replace all the trans lines?
Hey guys, I’m trying to install my kit I only got 2 long hoses do you know the length I should cut the one?
Okay so do they make a kit to bypass that intercooler..
Yes our kit is no longer pre cut so you can bypass the heat exchanger.
@@pddofficial can you give me some more details on that kitt
I don't know how to send you a picture on this thing..but these lines hooked into the outer cooler or leaking like crazy..
Mine has a small seep at fitting. Could I have a bad fitting ? Just installed everything else is solid no leaks
Possibly give us a call and we can get that sorted out for you.
A how come you guys don't have your heat exchanger by pass kit
What about for the 09 trucks
We are working on it stay tuned.
What would you guys recommend for a pump to pump 85w140 gear oil gear oil to oil cooler....we have a old Doug Nash overdrive behind a C6 and the Doug Nash over heats in overdrive running empty at about the 100-150mi mark
That kit is just what I need. What are the length of the lines? I am thinking of bypassing my exchanger and am wondering if the two large lines will work.
We offer the fitting kit and custom line lengths if needed.
hey with this kit when i select the 03-07 48re will it still have the lines for the heat exchanger? I see there's only one option that says heat exchanger?
Could someone please send a link showing me what a 4 way hydraulic wrench with 2 different angles as recommended in this video looks like? I tried to google but no info. Thx
www.amazon.com/TEKTON-Angle-Wrench-Keeper-Metric/dp/B07JHWRGTF/ref=asc_df_B07JHWRGTF/?tag=hyprod-20&linkCode=df0&hvadid=459730407112&hvpos=&hvnetw=g&hvrand=10892694390404141946&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9029909&hvtargid=pla-966899997789&psc=1
Are you still able to use a trans temp gauge into the hot line with this kit?
Where’s poppa saurus?
Make one for the 6.0
In the works!!!
Do you have just the quick connect fitting for sale I can buy for the trans cooler side for my 05 that are push lock style that I can just put a hose clamp on ?
Yes we do sell them here is the link for it powerdrivendiesel.com/product/3rd-gen-dodge-trans-cooler-quick-connects/
Are all these hoses the right length, or will some have to be trimmed?
They are a perfect fit. You will need a heat gun to get the line on. I have this kit on my 03 2500 with a 47 re. Make sure you also get the transmission line re moral tool.
Very helpful thank you
What do yall think about a 12v swapped cat eye 1500👀👀👀
Front end is probably too weak
@@austindoud273 I know it's the same design as what's under a duramax
Front end is completely different from 1500 to 2500 diesel
What the hell ia a 4 way hydraulic wrench lol
Double open end wrench, 30/60* angles
First 👊🏻💪🏻
Dang, how do you do it man?
Yes about time 😉😁
That’s why your wife left you.
Second. Where's my pin 📌
What’s up