@@mondayflix8389 too much humidity can be manage by placing very small of water inside the incubator and sometimes the area the incubator is placed can also hold humidity like a closed room, please try to place the incubator in outdoor area and check the humidity
When using a horizontal egg roller tray system (without limit switches) instead of the tilting rack system with limit switches, can I assume you can simply choose Left or Right to connect to the + side of the motor, and the - wire goes to the com (ignoring the other connection for the opposit direction) as you are only turning the eggs in one direction, "round". Can you join the neutral common of the heaters with the main power supply common instead of wiring to the neutral of the heater wire screw, or should each heater use a dedicated neutral back to the controller as directed? (Placing my controller a distance away from my incubator and want to minimize the total wires running to the unit from the controller so I can use a molex style quick disconnect and wall or panel mount my controller.
If you are using tilt motor you need to place the wires in the dedicated panels of controller , you need to place the heater wire in the controller not from the main board
So to be clear, all equipment gets its 220v (110v US model) power supply from the control unit, including the two manually switched accessory connections (circulation fan and light), both 220v/110v line out + neutral connections. I also assume the 12v + / _ connection is there as a power supply additional unswitched or externally switched DC equipment, such as a "door open" 12v light bank, or addition of a second 12v "always on" 12v circulation pc muffin fan positioned near the humidity source to help disperse it more evenly?
@@Umairworkshop I used a voltmeter to test the output. I believe it may be the location of the power supply for a 12v model option they may offer or plan to offer in future (+/_ DC = Line/neutral 110v/220v AC). It's probably best to design the housing once and not use the function than to have to remanufacture the entire unit for a small future mod. My thoughts without taking it apart. Here's a Question for you: I'm building an incubator lockdown unit and I want to incorporate a backup smaller (stc-2000 series) temp and humidity controller inside the unit, instead of having to remotely install the XM-18D "shoebox" sized controller on a wall. I'm wondering, if I make sure not to have both controllers powered on at the same time (a 3 way on1/off/on2 switch), could I wire the heating source to both units without issues? The XM18 connection provides power through the controller relay, whereas the stc unit is just a switch, so the heating element and humidity maker need external power and the neutral being interrupted by the controller relay switch? I fear that I may back load the heater or the stc backup control unit when the other is powered on. I guess I will have to draw it up and follow the potential for problems on a schematic.
Hello I watch your videos about incubators and I love them❤. Yesterday I purchased xm 18d with a humidity sensor having 4 wires and after connecting the sensor to the controller as per manual the humidity level is showing 20-21 relative humidity. Kindly tell me what to do. Thanks you 🙏🏻
@@Umairworkshop Thankyou for your reply 🙏🏻 I checked with other sensor still the issue persists so I ordered for a replacement. Waiting for the replacement to arrive
Does this XM-18D driver work for my 110v voltage? If so, should I buy it with 110v specified or does it work with 220v even though my electrical network is 110v? tanks
Thanks for the explain everything clearly. I bought xm 18d . But don't get the user manual. Search for manual on net . But can't get. If u won't mind then can u help me to get the user manual please?
You are welcome, you can search on Google in pictures , here is the unboxing video you might see the user manual th-cam.com/video/_SJ4mpKdwyA/w-d-xo.html
Great video Umair. I followed the video but the egg turning motor I had still has issues. No power. Do I need to add connecting wire between COM 1 and COM2. Also can you share the operating instruction manual. I'm unable to locate it online. Thanks.
If you are connecting 3 wire actuator it will be placed in motor wiring , but for 12v you can wire 12v power supply to motor wiring which will power 12v actuator
Hello and thank for the nice video i have an question i have the same incubator but when i want to go the temperature 43 c it doesn't let me and i do all the parameters when it go to 37,8 it cut and start the ventilation and in to the panel write d1 maybe you can help me
Incubator temperature is supposed to be under 39 celcius , I don't understand why you want to go over 43 celcius , if you want you can change the over temperature limit from internal setting
@@Umairworkshop thanks for the fast answer i need it for another jod nor for egg incubator. How can I change the internal setting i have already change the p1 p2...... And still cut the themperature in 39
bro I have some doubts with this automatic incubator controller please help me dout 1 : bro can we use 2 normal auto swing motors for 2 wodden Egg trys or we have to use same exact motor you used in the video.? because the one you shown in the video is not matching for the wooden tray dout 2 : can I use 2 cooling fans 4" to spread heat equally inside the incubator with automatic function and not manually by fan switch. (exhaust fan for pull excess heat and moisture from the incubator)
Hi, I have the same model, but the humidity alarm always rings, I put a new meter on I did the test and it works, using a multimeter to see when the humidifier turns on and it has no current, that is, the humidifier never turns on, I already installed it the temperature sensor to the maximum next to a source of hot temp and it also works, but it never triggers the humidifier. how can i solve this?
Hi sir thanks for the video I have one doubt about the motor rotation. To initiate the motor rotation we keep pressing means long pressing the button. When ever requirement is there need to do this activity for every time ? Means motor automatic starting is there or not sir
Salam alaikum, your channel is the best I ever come across, I think you should have tutorial class online. Pls can you explain Xm18k-2 wiring and setting. You're a genu
Very well explained, and nicely down in English, which is a rarity I've found on You Tube. Much appreciated!
Thank you for appreciating
1st! Thank you very much from your friend in America. I look forward to more in this series. Your channel is the best! : )
Are going to built an incubator with this unit?
You are welcome , thank you for appreciating
Maybe if someone demand to make on this , it is costly so it is only used in upto 1000 eggs
Bahut hi shandar explanation hai aapka.. shukriya ❤
You are welcome
Thanks so much. Nice and clear explanation 👍💐
You are welcome
Hello Umair, I recommend you talk more about the motor, limit switch and how to connect it to xm18d in details and how it works ....it's so confusing
I will try to explain the wiring in the upcoming videos
@Umairworkshop and how do you control too much humidity in an egg incubator
@@mondayflix8389 too much humidity can be manage by placing very small of water inside the incubator and sometimes the area the incubator is placed can also hold humidity like a closed room, please try to place the incubator in outdoor area and check the humidity
@@Umairworkshop ok thank you...I was able to build my own incubator and I will test it as from today....I will tell you the results
@@mondayflix8389 you are welcome , yes please give update on the progress
When using a horizontal egg roller tray system (without limit switches) instead of the tilting rack system with limit switches, can I assume you can simply choose Left or Right to connect to the + side of the motor, and the - wire goes to the com (ignoring the other connection for the opposit direction) as you are only turning the eggs in one direction, "round".
Can you join the neutral common of the heaters with the main power supply common instead of wiring to the neutral of the heater wire screw, or should each heater use a dedicated neutral back to the controller as directed?
(Placing my controller a distance away from my incubator and want to minimize the total wires running to the unit from the controller so I can use a molex style quick disconnect and wall or panel mount my controller.
If you are using tilt motor you need to place the wires in the dedicated panels of controller , you need to place the heater wire in the controller not from the main board
Sorry XM 18 D if i have can i use for mannual incubator?
Yes XM18D can be use for manual incubator
@@Umairworkshop thanks from Tanzania
@@graysonmatali644 you are welcome
So to be clear, all equipment gets its 220v (110v US model) power supply from the control unit, including the two manually switched accessory connections (circulation fan and light), both 220v/110v line out + neutral connections. I also assume the 12v + / _ connection is there as a power supply additional unswitched or externally switched DC equipment, such as a "door open" 12v light bank, or addition of a second 12v "always on" 12v circulation pc muffin fan positioned near the humidity source to help disperse it more evenly?
I still don't understand about those 12v relay even place a 12v led to it and place relay circuit but it doesn't work for any purpose
@@Umairworkshop I used a voltmeter to test the output. I believe it may be the location of the power supply for a 12v model option they may offer or plan to offer in future (+/_ DC = Line/neutral 110v/220v AC). It's probably best to design the housing once and not use the function than to have to remanufacture the entire unit for a small future mod. My thoughts without taking it apart. Here's a Question for you: I'm building an incubator lockdown unit and I want to incorporate a backup smaller (stc-2000 series) temp and humidity controller inside the unit, instead of having to remotely install the XM-18D "shoebox" sized controller on a wall. I'm wondering, if I make sure not to have both controllers powered on at the same time (a 3 way on1/off/on2 switch), could I wire the heating source to both units without issues? The XM18 connection provides power through the controller relay, whereas the stc unit is just a switch, so the heating element and humidity maker need external power and the neutral being interrupted by the controller relay switch? I fear that I may back load the heater or the stc backup control unit when the other is powered on. I guess I will have to draw it up and follow the potential for problems on a schematic.
@@SybilDefense you can place them both in different wiring if xm18 have any issue then stc2000 will cover it
Hello I watch your videos about incubators and I love them❤. Yesterday I purchased xm 18d with a humidity sensor having 4 wires and after connecting the sensor to the controller as per manual the humidity level is showing 20-21 relative humidity. Kindly tell me what to do. Thanks you 🙏🏻
You are welcome, it is supposed to work okay you can check it with other humidity meter if it is showing error
@@Umairworkshop Thankyou for your reply 🙏🏻 I checked with other sensor still the issue persists so I ordered for a replacement. Waiting for the replacement to arrive
Does this XM-18D driver work for my 110v voltage? If so, should I buy it with 110v specified or does it work with 220v even though my electrical network is 110v? tanks
It comes in both voltages of 110v and 220v you need to confirm from the seller if it is 110v
Thanks for the explain everything clearly. I bought xm 18d . But don't get the user manual. Search for manual on net . But can't get. If u won't mind then can u help me to get the user manual please?
You are welcome, you can search on Google in pictures , here is the unboxing video you might see the user manual
th-cam.com/video/_SJ4mpKdwyA/w-d-xo.html
Xmd 18 D can used with solar power to run?
Yes it can work on solar power with inverter because it need 220v
@@Umairworkshop thank you
@@Umairworkshop thank you
@@graysonmatali644 you are welcome
Great video Umair. I followed the video but the egg turning motor I had still has issues. No power. Do I need to add connecting wire between COM 1 and COM2. Also can you share the operating instruction manual. I'm unable to locate it online. Thanks.
It is 15,17 and 18 which motor are you using if it is 2 wire tray then 15 and 17 is connection
Sorry hot bulb you use has how many Volt?
It is 100 watt bulb, but can use up to 500 watts
@@Umairworkshop nice for education to us from Tanzania
@@graysonmatali644 nice to see you
Good tutorial in this video
Thank you
How would I wire linear actuator ?
12v
If you are connecting 3 wire actuator it will be placed in motor wiring , but for 12v you can wire 12v power supply to motor wiring which will power 12v actuator
Dear can I use 2 machine of 60ktyz motor in xm-18d?
Yes two motors can be connected
Great work there with clear explanation. I liked it and thanks.
Any idea where I can get a "down button" as mine is not working?
Would appreciate.
Thank you for appreciate, all the button may be available in electronics market
Ispe ktna load daal skte hn
Around 3000 watts
Tengo el equipo XM18S 220. Por favor me puedes indicar: donde conecto la resistencia de calor o temperatura. Y donde conecto el humificador? Gracias
Here is the wiring tutorial
th-cam.com/video/tNtN11-mkOw/w-d-xo.html
Bhai Maximum kitne ando ko hatch krne k liye use kr sakte hain
Yeah wala 3k eggs tak ki machine control kar sakta hai
@@Umairworkshop Shukriyah bhaai reply karne k liye👍
@@danishnoor9883 you are welcome
My incubator rotating motor is not stopping after touching the limit switch what could be the problem?
Try changing limit switch
@@Umairworkshop yes I changed it even then it doesn't stop it keeps rotating.
@@supersaiyan4539 have you done the motor wiring yourself or it was already made
Hello and thank for the nice video i have an question i have the same incubator but when i want to go the temperature 43 c it doesn't let me and i do all the parameters when it go to 37,8 it cut and start the ventilation and in to the panel write d1 maybe you can help me
Incubator temperature is supposed to be under 39 celcius , I don't understand why you want to go over 43 celcius , if you want you can change the over temperature limit from internal setting
@@Umairworkshop thanks for the fast answer i need it for another jod nor for egg incubator. How can I change the internal setting i have already change the p1 p2...... And still cut the themperature in 39
@@Umairworkshop also your video was so helpful for me keep doing your good jod hello from Greece
@@ivansenko9634 you are welcome
bro I have some doubts with this automatic incubator controller please help me
dout 1 : bro can we use 2 normal auto swing motors for 2 wodden Egg trys or we have to use same exact motor you used in the video.? because the one you shown in the video is not matching for the wooden tray
dout 2 :
can I use 2 cooling fans 4" to spread heat equally inside the incubator with automatic function and not manually by fan switch.
(exhaust fan for pull excess heat and moisture from the incubator)
Yes you can use any motor of 220v
Yes you can use 4 inches fan for even heat distribution
thank you bro 😊
but my dout is 4" cooling fan can use automatically right
not by manual fan switch right😅
sorry for the too many doubts bro😅😅
@@johnwesley8658 that button is for aur circulation fans it is up to you if you want to connect with button or directly
Hi,
I have the same model, but the humidity alarm always rings, I put a new meter on I did the test and it works, using a multimeter to see when the humidifier turns on and it has no current, that is, the humidifier never turns on, I already installed it the temperature sensor to the maximum next to a source of hot temp and it also works, but it never triggers the humidifier. how can i solve this?
If it is not opening humidifier than the relay inside is faulty for humidifier only
@@Umairworkshop is it possible to replace?
@@DomingosVarela you need to get it checked by electrician who can solder new relay
What is the use of +12V and Ground?
I think that will open the circuit when there is no power
I'm staying in Bukoba, Tanzania, East Africa . How can I have such units?
You need to search on Google if someone have it in your country
Hi sir thanks for the video
I have one doubt about the motor rotation. To initiate the motor rotation we keep pressing means long pressing the button. When ever requirement is there need to do this activity for every time ? Means motor automatic starting is there or not sir
You are welcome, the turner is automatic don't need to do anything
Salam alaikum, what is difference between Xm-18k-1and 2 and Xm18d
They have added features such as light and fan button and wifi
th-cam.com/video/6vFgqn0Kolo/w-d-xo.html
Salam alaikum, your channel is the best I ever come across, I think you should have tutorial class online. Pls can you explain Xm18k-2 wiring and setting. You're a genu
@@ahmada.abdulrahman16 thank you for appreciate , I think xm18k-2 have same wiring as xm18 series and internal setting are same for all of them
Tengo un xm 18e la alimentación de energia es de 220v, tengo el volteador de 110 v, las bujias de cuales necesito, no lo je podido instalar
Please find 220v turner because controller will only getting the 220v in and 220v output
Bro best heat source for incubator ? For best result and for 200 to 300 capicaity inqubator how much bulbs and of which wats are good ?
You can use 300 watt rod heater or ceramic heaters
@@Umairworkshop thanks bro
Exhaust fan and humidity control is AC or DC?
Both of them are 220v AC
Bhai ye motor kaha milegi
Here is the information in description
th-cam.com/video/Y9XikJOPRoA/w-d-xo.html
@@Umairworkshop motor ka price ky h
Aur all parts ki price bhi bataiyega
parts price in market mention here
th-cam.com/video/1rDyky50og4/w-d-xo.html
How to turn off the alarm
Keep pressing the down button alarm will turn off
What is the Price
It is around 12k In market
Thanks bhai,video hindi भाषा मै बनाओ
You are welcome
Bhajan pura model ki video banakar send Jani ke ise instead Karke dikhayen
You means isko incubator mein install karkay
Bhai yah video 1 hindi me bana do please poora connection hindi me bana bhai please
Mein puri Koshish karunga isko Hindi language mein bnanaay ki next videos mein
L for line.. Not load
Thank you for good information
Hindi MP Mandsaur good
Thank you
Hi
Hi nice to see you