This is a stark reminder of why I gave up working on cars, at least as much as possible. Some people just can't understand why I say no, may be I should send them here lol Good job fella.
Kevin-Albert Williams One thing tough: I cleaned under the hood today, resulting in high idle, Engine Malfunction and Transmission service required. Any hopes those alarms will dissappear when it dries up properly?
Good work mate, I remember those Mondeos well spent 10 years working on the mk1 and 2s, Ford's slave units don't get any better plastic crap, I remember my own mrk 2 being just as bad, so surprised none of those subframe bolts didn't continually spin the nut in the frame it's always the ones on the floor pan that spin, a real pain as we had to open the floor pan up and weld the nut back in place.
Very true about the captive nuts spinning in the boxed up chassis...,, whoever came up with that design 😆.., they only way I get around that is I use a ton of WD40 constantly before I attempt to crack them..,, I’ve seen many mechanic having to cut the floor pan to access it. Or even slicing the box chassis to get a spanner on it. Thanks for the review ..,, really appreciate the feedback.
Takes it out of you working under cars my back and poor nees are feeling it I have a bmw 5 series clutch to do Im lending my mates ramp it will feel luxery Conpared to been on floor 😂🤦♀️
hey, nice work. i own mk4 mondeo and I think clutch pedal is a bit stiff for me. it works wine - no slips, bites at the middle of the travel etc. any ideas what could done ta make it lighter?
great video mate, quick question, will I need to re-align the subframe only I've read it's quite important to do so? does the way you do I do away with the need to re-align the subframe? Thank you
Wayne only if you’re fully removing all 4 corner bolts. In this case I only remove the two from gearbox side sow there is no side movement as the other side is firmly attached. There’s only up and done movement. So no need for alignment.
You know when someone's made it look easy that they are skilled at what they do. Good job bruv. Quick question, can I get the gearbox out or do I need to drop the full subframe on this model?
Hi do you need a special tool for fitting the pressure plate to the flywheel on the focus 1.8 tdci not sure if it has a self adjuster built into the pressure plate on these ?
Hi Kevin is that engine the same as the engine in the 08 s max and galaxy ? Also what’s the proper way to instal the throw out bearing /slave cylinder ? What did you put on the back of the cylinder ?
@@WMCS I have an issue with an 08 s max 5 speed where I bought it knowing it needed a new flywheel so what I did was I actually went second hand as the cost was attractive and I also got the clutch kit from the breakers also for 80 euro instead of 400 euro I installed the mondeo 1.8 flywheel and clutch from the breakers and left the original throw out bearing in and when I went to bleed the clutch fluid started pouring from the gearbox ( brake fluid ). I opened the gearbox and the original throw out bearing was smashed to pieces So I put a new throw out bearing in ( Sachs ) I also took the second hand clutch kit out and put the original clutch kit in ( previous owner had new clutch in about 5 months before I bought it ) I buttoned everything up and went to bleed again and the same thing happened brake fluid started pouring from the gearbox ( but this is with a brand new throw out bearing ) does the issue lie in the fact I used a second hand flywheel and clutch kit ?
Great video buddy.. One thing I have wrong with mine is theres a wee oil leak from the sump I've been told I need the silicone replaced aroung it would it be something easy to do.?
@@WMCS yeah who ever had the car before me never replaced the bottom engine cover so a little easier to get at. But would there be any good sealant to get or are they nearly all the same
vous êtes très fort et en plus vous trouver le moyen de bien filmer.....bravo! est ce que c'est la même procédure pour une mondéo td endura de 1997 ? si vous avez le temps pour répondre bien sur! merci
Stojan Humar yes I replaced the DMF .. you can get conversion kit to solid flywheel. But you will always have a judder or vibration when pulling of as there won’t be any dampening effect from the force of the engine to the gearbox.
4 hours......bloody hell it takes me that amount of time to drink a cup of coffee.........jokes aside that can only be done in that time by someone like yourself who know what they are doing and also have the experience.....normal people will take much longer.
You must be The God of clutches I have sent your video to some mechanics and told them that if they are even so so mechanics then they can replace my clutch in 2 hours, while watching your video. All of them say no and say that it will take them whole day. That means that they are brain dead , absolute waste mechanics with no skills and no pride. I have told them that they have no pride and brain dead and hanged up after they have refused to even try to do it in 2 hours , learning from your video. P.S. My car is the same as in your video
Great work man. That is not easy work. But just wondering, why would people opt for a mobile clutch replacement rather that go to a garage.? Like even if the clutch was fried and the vehicle needed recovered, would that not be the better option? Not dissing your work by the way, you do a great job.
Revelation - never knew a Mondeo could be done on a driveway, thought it was an intensive ie costly operation on a ramp for a couple days?..chucked mine away as I thought it would cost a 4 figure fortune.
Witheredgoogie definitely a fairly straight forward one. If you’ve got some mechanical knowledge you’re looking about 4 hours ... cost incl parts just above a monkey. ...
@@WMCS Thanks for the reply, that is a great price compared to what I have been hearing for ages..I got the impression the DMFs are specially made in Hatton Garden LOL
Witheredgoogie 😂😂... they are quite pricey if you’re buying them retail. Or sometimes even trade. I buy in bulk so I only pay factory price. And doesn’t put any mark up on it.. I give my customer that deal When I do the repair. I only charge labour cost. Have a great Christmas and happy new year 🥳... thanks for visiting the channel as alway. Appreciate it.
hello kevin..pour le berceau d'une mondéo de 1997 td endura, je peux me lancer ? c'est bien pareil ? merci d'avance pour ton conseil car je doute un peu....super travail en tous cas ....merci
Don't know wat ur smoking but that's how all mechanics work can't be pussy footing around when ur an experienced trades man and know wat ur doing ull fly thru the work like this does knows his stuff
![[ไฮไลต์] "บิว" ภูริพล บุญสอน วิ่ง 100m ชาย รอบคัดเลือก | โอลิมปิก 2024](http://i.ytimg.com/vi/3kUSMfgtQ5s/mqdefault.jpg)
This is a stark reminder of why I gave up working on cars, at least as much as possible. Some people just can't understand why I say no, may be I should send them here lol Good job fella.
Was contemplating doing my mrk3 but you completely put me off thats a whole load of headaches i dont need in my life ! Lol thanks great vid! 👍
albo1585
Lol. It can get a bit in depth. Thanks for the feedback tho.
Got to respect a guy doing a clutch on he’s back on a driveway 👍
You are very good at what you do Mate and love your techniques.
Colin Dicken
Thanks for the positive feedback
Colin Dicken
Thanks for the positive feedback Colin.
Bc of this video I was able to change the power steering rack on my Mondeo. Thank's a lot.
Glad to hear the video came through for you ..,, thanks for letting us know ..,
Kevin-Albert Williams One thing tough: I cleaned under the hood today, resulting in high idle, Engine Malfunction and Transmission service required. Any hopes those alarms will dissappear when it dries up properly?
Btw, I used the water hose.
Rune Andersen just checks as a precaution the breather pipe has come loose ....
Rune Andersen by any chance the brake pedal feels quite heavy ..?
A lot of work that one, well done again.
Thank you.
Nice camera angles, can see that you have taken some time extra for better view. Great video
Good work mate, I remember those Mondeos well spent 10 years working on the mk1 and 2s, Ford's slave units don't get any better plastic crap, I remember my own mrk 2 being just as bad, so surprised none of those subframe bolts didn't continually spin the nut in the frame it's always the ones on the floor pan that spin, a real pain as we had to open the floor pan up and weld the nut back in place.
Very true about the captive nuts spinning in the boxed up chassis...,, whoever came up with that design 😆.., they only way I get around that is I use a ton of WD40 constantly before I attempt to crack them..,, I’ve seen many mechanic having to cut the floor pan to access it. Or even slicing the box chassis to get a spanner on it.
Thanks for the review ..,, really appreciate the feedback.
master of clutches
Respect pentru munca ta !!!!❤
The subframe has some aligning holes, didn't you had to align it before tighten it up ?
I will do it soon on m'y focus because if thé flyweel death of course ahaha, this vidéo IS so good and helpfull thanks you
Good work pal there bloody sharp them air boxes when ragging them out I've got more scares on my hands from them lol
You’re absolutely right there. The amount of times I’ve looked at my bones 🦴 with cuts. My hands are like a sieve 😆🤩
Takes it out of you working under cars my back and poor nees are feeling it I have a bmw 5 series clutch to do Im lending my mates ramp it will feel luxery Conpared to been on floor 😂🤦♀️
Can you remember what the flywheel bolt torque was on this mate?? Doing one just now and can’t find the info anywhere
Domestic bliss in that house 🤣🤣. Pro you make it look easy 👍🏻
Michael Ashton thanks for the review much appreciated... 😁
Asta este roman ....ciocan ,ranga.....spor la treaba!!
Pai de unde stii ca e romin?
@@olegolegov726 Romanu lucrează cu ciocanu și rangă...
Is it the same for the 2.0 tdci 6 speed manual?
Hey Kevin, great tutorial, is that Loctite 5980?
Are theese exact same clutch as the transit connect
hey, nice work. i own mk4 mondeo and I think clutch pedal is a bit stiff for me. it works wine - no slips, bites at the middle of the travel etc. any ideas what could done ta make it lighter?
There is a reset tool you use the set the clutch up... There tuts on TH-cam
How did you bleed this clutch?
I disconnected the subframe from only one side now the steering knuckle is not lining up what have I done wrong?
great video pal.
Thanks.
Bon travail merci♥️♥️♥️♥️
Driss Auto pas de probleme.... merci aussi pour visiter le channel et merci pour votre review... excuse un Peut mon francais
@@WMCS je suis mecanicien auto anvi mois♥️
Driss Auto c’est bien ca...
Can you take the gearbox completely out that way too?
Merci pour votre ade.
great video mate, quick question, will I need to re-align the subframe only I've read it's quite important to do so? does the way you do I do away with the need to re-align the subframe? Thank you
Wayne only if you’re fully removing all 4 corner bolts.
In this case I only remove the two from gearbox side sow there is no side movement as the other side is firmly attached. There’s only up and done movement. So no need for alignment.
Thanks mate that gives me more confidence to tackle the job. 👍
You know when someone's made it look easy that they are skilled at what they do. Good job bruv. Quick question, can I get the gearbox out or do I need to drop the full subframe on this model?
Thanks mate. Definitely need to drop one corner of the subframe. Makes life a lot easier.
thank you Kev
Hope Marge video was helpful
Thanks for such a good walk through! I hope you don't mind me asking, where do you get your parts from?
hvalladares it’s all from Euro car parts
@@WMCS Thanks 👍
Hi do you need a special tool for fitting the pressure plate to the flywheel on the focus 1.8 tdci not sure if it has a self adjuster built into the pressure plate on these ?
tony pond
All you need is a £10 clutch alignment tool. From euros or Halfords
@@WMCS ok Thanks
Hi Kevin is it difficult to replace the throw out bearing in the s max. Same engine as this
The Smax is easier as there are no subframe. I’m sure there’s one in the channel. Let me know.
What did you do as regards the steering rack thats bolted to subframe
Detach the column from inside.
what engine oil does this engine like?
i like tinkering with cars but fk that lol good job there sir
Best !!!
Hi i have ford mondeo 57 plate 1.6 petrol is that same .....
Great video
did you replace with dual mass SACHS again?
Stojan Humar ... Yes it was a GAT manufactured by SACHS.
Hi Kev do you have to take the steering rack off to do this job regards David
Hey David.
No you don’t have to disturb the steering rack. Have a look at the jag x type for a very detailed description. Exactly the same platform.
Was it 5 speed transmission? I need to remove 6 speed mmt6 gearbox from mondeo mk4 LHD (clutch is fine, gearbox need repair)
Karol they’re almost identical. Only difference is the gearbox lever where the gear linkage attaches.
@@WMCS Thanks for Your answer!
Very good work
Hi Kevin is that engine the same as the engine in the 08 s max and galaxy ? Also what’s the proper way to instal the throw out bearing /slave cylinder ? What did you put on the back of the cylinder ?
It’s exactly the same engine and gearbox. That’s black rubber sealant ., as they don’t come with an O ring
@@WMCS I have an issue with an 08 s max 5 speed where I bought it knowing it needed a new flywheel so what I did was I actually went second hand as the cost was attractive and I also got the clutch kit from the breakers also for 80 euro instead of 400 euro
I installed the mondeo 1.8 flywheel and clutch from the breakers and left the original throw out bearing in and when I went to bleed the clutch fluid started pouring from the gearbox ( brake fluid ). I opened the gearbox and the original throw out bearing was smashed to pieces So I put a new throw out bearing in ( Sachs ) I also took the second hand clutch kit out and put the original clutch kit in ( previous owner had new clutch in about 5 months before I bought it ) I buttoned everything up and went to bleed again and the same thing happened brake fluid started pouring from the gearbox ( but this is with a brand new throw out bearing ) does the issue lie in the fact I used a second hand flywheel and clutch kit ?
Thanks for replying kevin
Great video buddy.. One thing I have wrong with mine is theres a wee oil leak from the sump I've been told I need the silicone replaced aroung it would it be something easy to do.?
If it’s just the sump. Not too bad.
@@WMCS yeah who ever had the car before me never replaced the bottom engine cover so a little easier to get at. But would there be any good sealant to get or are they nearly all the same
Did you use a torque wrench for clutch and flywheel or can you get away without using one
I can. I’m not sure about anyone else. So I will suggest if unsure to use one.
vous êtes très fort et en plus vous trouver le moyen de bien filmer.....bravo! est ce que c'est la même procédure pour une mondéo td endura de 1997 ? si vous avez le temps pour répondre bien sur! merci
tempsx 92 salut. Our c’est la meme procedure. Exactement la meme chose. Merci pour le feedback positive. J’espere que mon Francais est asser bien.
I'd never thought of doing it like that, leaving the subframe in and wedgeing it in like that.
zoidberg444 yes mate and it’ll only take you about 4 hours max...
@@WMCS did you replaced with Sachs DMF? How single mass flywheels work on those engines?
Stojan Humar yes I replaced the DMF .. you can get conversion kit to solid flywheel. But you will always have a judder or vibration when pulling of as there won’t be any dampening effect from the force of the engine to the gearbox.
4 hours......bloody hell it takes me that amount of time to drink a cup of coffee.........jokes aside that can only be done in that time by someone like yourself who know what they are doing and also have the experience.....normal people will take much longer.
very good 🤩^^
fancy coming to do my clutch
You must be The God of clutches
I have sent your video to some mechanics and told them that if they are even so so mechanics then they can replace my clutch in 2 hours, while watching your video.
All of them say no and say that it will take them whole day.
That means that they are brain dead , absolute waste mechanics with no skills and no pride.
I have told them that they have no pride and brain dead and hanged up after they have refused to even try to do it in 2 hours , learning from your video.
P.S.
My car is the same as in your video
Hi Kevin did it really take you just 30 mins to do the clutch ?
That’s just the edited version. Actual repair times about 4hrs
Hi, if I want to change the crank seal from the transmission pulley do I need timing tools ?
Most likely as you’d need to remove the crank pulley which the belt sits on.
Kevin-Albert Williams Yeah but the timing chain sprochet its locked in the crank shaft , it has a guiding pin on ,
Don’t give up. Do a bit of research on it.
Hi buddy how much would the clutch be to replace on this model of mondeo buddy?
Send your details via.
www.williamsmobileclutch.co.uk
And I’ll get a price across to you.
Thanks
Great video.
Is the process still possible in the same way on the 2.0 tdci, I know the mounts are similar.
Cheers
Yes..,, even the gearbox should be the same ..
hello and greetings good job i also work just like you i know what hard work it is greetings from coventry anyway
Nice video, but it’s a tough job pulling the transmission off on your own and on stands as well
A little bit heavy but do able ✨✨🍻🍺
Once again 👏👏👏👏👏👏🍺🍺🍺🍺🍺
You are a real hero! You are one hardworking #%*”€$£! Thank you for your effort!
Peter thanks for the feedback... and for visiting our channel. 🍻
@@WMCS hey how much would you charge for a 2l tdci mondeo 2009 fly and clutch replacement?
Just out of interest
Flame Innit roughly about £700 I think. If you want an exact price text me over your Reg
07376369067
how much does it cost to change the clutch
Adrian Vasile £300
Did you unbolt the subframe at both sides to get clearance?
One side completely off. One side slack only. More than enough clearance to even remove the box completely
I think on the 2.0 6speed box all the subframe off ..I done this brought the t-shirt.
Well I have just messaged the man himself regarding a 2.0 6 speed diesel 😶🌫️
I've got a borg@beck solid conversation kit
Great work man. That is not easy work. But just wondering, why would people opt for a mobile clutch replacement rather that go to a garage.? Like even if the clutch was fried and the vehicle needed recovered, would that not be the better option? Not dissing your work by the way, you do a great job.
kmcca08 must be cost then
No swearing ? How do you get on when it's pouring with rain.
where the transmission oil ?
you don't need gearbox oil mate
Revelation - never knew a Mondeo could be done on a driveway, thought it was an intensive ie costly operation on a ramp for a couple days?..chucked mine away as I thought it would cost a 4 figure fortune.
Witheredgoogie definitely a fairly straight forward one. If you’ve got some mechanical knowledge you’re looking about 4 hours ... cost incl parts just above a monkey. ...
@@WMCS Thanks for the reply, that is a great price compared to what I have been hearing for ages..I got the impression the DMFs are specially made in Hatton Garden LOL
Witheredgoogie 😂😂... they are quite pricey if you’re buying them retail. Or sometimes even trade. I buy in bulk so I only pay factory price. And doesn’t put any mark up on it.. I give my customer that deal When I do the repair. I only charge labour cost.
Have a great Christmas and happy new year 🥳... thanks for visiting the channel as alway. Appreciate it.
@@WMCS Keep up the good work and have a restful Christmas break. and plenty in the New Year.
Hi, is it the same for a 2008 2.0 tdci 6 speed?
Did u just replace the slave cylinder in this Kevin?🙏🏎️🏎️
Yes that’s correct.
👍👍👍
Do you not have to bleed the gearbox ?
Hi Peter..
If it is hydraulic then you have to bleed it and fill with correct oil..
Thanks
hello kevin..pour le berceau d'une mondéo de 1997 td endura, je peux me lancer ? c'est bien pareil ? merci d'avance pour ton conseil car je doute un peu....super travail en tous cas ....merci
tempsx 92 oui mais faire attention... toujours avec quelqun pour t’aider
@@WMCS merci kevin
tempsx 92 pas de problem... 😇
Must be some good money in that garages want ££££
Simon Parker I get through one everyday. It’s a tough job comes winter tho.
Do yo do around the West Midlands?
Yes I do.
كل يوم قبل النوم تعلم واكتشف وعيش حياتك كلها( +عاش من عرف قدر نفسه)
Haven’t a clue what your saying
@@seanconnelly2832 mate its 2021 ......humans have innovated tools and apps...you can use google translate if you want to know
and i dont see the clutch replacement,only disassembling and assembling parts
قهوة قهوة قهوة لزم تبلذها تشرب تاي بالنعناع ولا الحلبة تنحي الخلقة.... َ
Is it just me that think that Fords seem more complicated built then VAG's ?
It’s definitely more complicated depending on the model. But the newer ones are like a bit of a maze 😁✨✨
@@WMCS I can see that👍👍
If I tried this I'd be dead under the car within an hour😂. pass.
place pages 🥳😂... I feel like that on a Friday afternoon... like a kid that keeps asking the parent. “Are we there yet “...😂😂
shitty design these mondeos my mk3 was the same
to much hurry, no care for disassembley the oder parts, i wood never pay a mecanic that do that to my car
You're clearly not watching any mechanic then!
This is exactly the type of no nonsense mechanic I would want doing my banger 👍
@@DavidMoralee yes... I never seen no mecanic.... Because i fix my car myself🤮
Sinner _87 stick some reviews then instead of talking about It
Don't know wat ur smoking but that's how all mechanics work can't be pussy footing around when ur an experienced trades man and know wat ur doing ull fly thru the work like this does knows his stuff