Shiny Solder Balls! 😉 I think You shuld put some uv mask on the other board on the same pin, just to minimize the chance of an unwanted connection. I’d put them boards in the UC before soldering them togerher. There were so much junk on this board, and the UC would get rid of all the tiny left over from the paste. I really enjoyed this long vid! Keep em coming!
Shiny solder balls! I watched this in the background while working on an 11 board, short on VDD Main under the shield on top board, took a while to find it
When reballing the bottom board I ussualy apply the paste and then remove the stencil. My Quian Li is universal for 11/pro/max and it does not hold when heating. Then I put the board on heater - works great
Had same thing happen with me. Worked in jig but not after reball. I was kinda in the same boat cause the UBIF near me deep fried the board 😂 Love the videos man!! ❤️
@@VCCBoardRepairs amazing, reach temp take lot of time even 400 degree, probably housing take lot heat mass but temp reaching slowly and protecting a board.
It's the DT-880 🛒Buy a DT880 Mini DC Power Supply: www.vccboardrepairs.com/buy-dt880 🛒Buy the iPhone Power Cable for iPhone 11: www.injuredgadgets.com/mechanic-iboot-power-supply-test-cable-for-iphone-11-11-pro-11-pro-max/?acc=3d2d53e5abcd70e24cc444935b88e6ac21 ►Full list of Solder Tools here: www.vccboardrepairs.com/gear
I saw a video on facebook recently where they put a screw partially into one of the screw posts and then they used that screw as a lift point when separating the sandwich. Have you ever used that technique? Any thoughts?
At the end all it needs some weight on top of the board to make a better connection... But thanks for the long video awesome work. I don't spend more the 1 hour on each device. 😇 but keep them coming.
After i reball, i don't like to put pressure. Had many cases where the solder balls squeeze out & short things out. Off camera, I tried other things to get it working but no luck. So probably a bottom board issue.
I'm still watching the video just wanted to comment on the 46:42 part. Ya I seen that line act crazy alot haha. Now let's get back to the video. See you later 😆
Shiny Solder Balls! 😉
I think You shuld put some uv mask on the other board on the same pin, just to minimize the chance of an unwanted connection.
I’d put them boards in the UC before soldering them togerher. There were so much junk on this board, and the UC would get rid of all the tiny left over from the paste.
I really enjoyed this long vid!
Keep em coming!
Ah, that's a good idea!
I wish i had my USC ready to go, but it takes so much time to setup 😂
Thanks for watching!
Thanks Jesse another beneficial video and it’s the ones that don’t work that help us understand what to avoid doing! Keep them coming please 🙏🏻
Yes this is true! Good point
11:55 we both said "wow" at the same time lol
hahaha. i don't blame you!
at the 37:30 mark. how do you not have a short while having the boards apart?
Because the short is on the bottom board.
I always get lost when trying to diagnosis the problems so it does help to watch you troubleshoot the board.
That's great to hear! Thanks for watching.
I don't have a iPhone and never getting one for sure but still enjoyed it !! Thanks to Louis I found u
I don't use an iPhone either! Lol. Thank you for watching!
Shiny solder balls!
I watched this in the background while working on an 11 board, short on VDD Main under the shield on top board, took a while to find it
Awesome! Appreciate it!
When reballing the bottom board I ussualy apply the paste and then remove the stencil. My Quian Li is universal for 11/pro/max and it does not hold when heating. Then I put the board on heater - works great
I used to use that method before with a Mijing stencil but it wasn't always consistent
I find this Qianli reballing jig gives more consistent results
Had same thing happen with me. Worked in jig but not after reball. I was kinda in the same boat cause the UBIF near me deep fried the board 😂
Love the videos man!! ❤️
Deep fried is a perfect description 🤣
Great work!
Shiny solder balls ⚽️ 😂
Haha thank you! 🙏
I never seen a board look this bad 🤢. But your right I would give up on this one. Great video and keep up the excellent work.
Appreciate it bud!
Nice work, have you got low temperature solder paste? May help with liquefy paste without too temp stressing board.
Thank you! Yes, I am using low melt solder for the reball. It's 148C
@@VCCBoardRepairs amazing, reach temp take lot of time even 400 degree, probably housing take lot heat mass but temp reaching slowly and protecting a board.
Shiny solder balls FTW
FTW! 🤣
Really like those pre-heaters as well. Pretty reasonably priced too.
Yes they are! I love it!
What's the name of the power supply u used on usb
It's the DT-880
🛒Buy a DT880 Mini DC Power Supply: www.vccboardrepairs.com/buy-dt880
🛒Buy the iPhone Power Cable for iPhone 11: www.injuredgadgets.com/mechanic-iboot-power-supply-test-cable-for-iphone-11-11-pro-11-pro-max/?acc=3d2d53e5abcd70e24cc444935b88e6ac21
►Full list of Solder Tools here: www.vccboardrepairs.com/gear
I saw a video on facebook recently where they put a screw partially into one of the screw posts and then they used that screw as a lift point when separating the sandwich. Have you ever used that technique? Any thoughts?
I don't like the screw method
At the end all it needs some weight on top of the board to make a better connection...
But thanks for the long video awesome work. I don't spend more the 1 hour on each device. 😇 but keep them coming.
After i reball, i don't like to put pressure. Had many cases where the solder balls squeeze out & short things out.
Off camera, I tried other things to get it working but no luck. So probably a bottom board issue.
13 minutes in and Jesse "Man, what the heck" 🤣
Hahahaa 😂
another great video - thanks Jesse
Glad you enjoyed it Thank you!
Which one using shematic diagram sir …?
I use ZXW for my boardview software
I’d guess the last shop used a bbq grill to heat the board
😂😂😂 probably
I'm still watching the video just wanted to comment on the 46:42 part. Ya I seen that line act crazy alot haha.
Now let's get back to the video. See you later 😆
Haha yeah that one always trolls me!
Shiny solder balls : )🎉
🤣🤣
@@VCCBoardRepairs I finished it til the end 😃
Shiny solder balls 🤣
hahaha yes!
Shiny Solder Balls are shiny. Wifi greyed out :-(
Yes they are! Haha
Shiny solder balls?
🙏🙏
Nice ❤️❤️❤️❤️❤️
Thank you 🙏🙏
Watching this as I work on a previous repair attempt lol smh
Don't you just love those! 😂
@@VCCBoardRepairs Noooo lol. It's always good when it's something easy that they missed and they didn't ruin it too bad tho
Haha yes!
Shiny solder balls damn
haha awesome
Louis Rossmann sent me here.
Amazing! Thanks for watching
Shiny solder balls!
🙌
Shiny solder balls
Haha nice
Rossmann sent me.
Awesome! Tell him thank you! 😅
Shiny solder ballz
🤣🤣
shiny solder balls
Shiny solder balls! haha
Shinny solder balls
🤣🤣 you made it that far!
@@VCCBoardRepairs No. Actually I accidently jumped to exactly that time in the video :D. Really!
Haha that's cool too!
@@VCCBoardRepairs It really is. That's why decided to share. Because I watched only few minutes and what are the chances to jump exactly on this :)
Shiny Solder Balls. :)
I'd sling that back in the box and get rid, thats got liability written all over it !
Hahaha
i saw
Jesus tap-dancing Christ.
Either it came in water damaged beyond repair or they just put it in a deep fryer instead of an ultrasonic cleaner
Probably deep fryer 🤣
shiny solder balls
Haha! You made it that far!