Jrunner Refuses to flash Timing Files with Xflasher and i have a AceV3 going on a trinity i cant even get the timing files programmed resoldered tons of times.
Yes. You shouldn’t need either for a S-RGH. As long as the console still works and there isn’t any trace damage. The Post point is the most important point for this, so as long as it is intact, then you should be fine.
@@hardcoregamer685 thanks for the reply, unfortunately after opening it up today in excitement I discovered it was in fact the post via that was pulled off alongside ft2v1. Rookie mistake!
@@Edin21 If you are willing to tinker and have a steady hand, you can scrape the silk screen on the top side near the apu, this is an alternative post point. If worst comes to worse, you can use a corona post fix adapter to get access to the post point.
Yes, this method doesn't require those points so would be a good alternative. Although, it does still require many points the same size, so practise your soldering first.
Yeah, glitch chips aren’t even needed anymore. I just uploaded this just in case someone didn’t want to try the harder RGH3 mod or damaged their PLL point.
@@TheModSmithI found a guy who made a Programmer for Pico but I have literally no clue at all how to use it. th-cam.com/video/eC3C9Ab8bRU/w-d-xo.htmlsi=_9ViuTa2zxDeSGdZ you would know much more about glitch chips than me so could you make a video on how to use this on the ace?
Hello guys, I screw up with the PLL point, and I have to follow this tutorial now... Can I use the JR programmer instead, and if yes,is the process harder or different from x flasher to program the ace v3? Thank you
![How to Change LEDs on an Xbox 360 [Ring of Light Mod]](http://i.ytimg.com/vi/Xszfkjoqpbs/mqdefault.jpg)
Jrunner Refuses to flash Timing Files with Xflasher and i have a AceV3 going on a trinity i cant even get the timing files programmed resoldered tons of times.
I have an ace v3 from a while back, but i do not have the wires anymore. Would you recommended 30awg kynar wire as an alternative?
Yes
I'm getting Flash Config: 0x00000000 even after resoldering. Any ideas?
I fixed this, was a bad solder.
Unfortunately it now wont post on the screen, not throwing signal via HDMI
Would this be a reasonable alternative for a failed RGH3 console? (Removed ft2v1 and pll points)
Yes. You shouldn’t need either for a S-RGH. As long as the console still works and there isn’t any trace damage. The Post point is the most important point for this, so as long as it is intact, then you should be fine.
@@hardcoregamer685 thanks for the reply, unfortunately after opening it up today in excitement I discovered it was in fact the post via that was pulled off alongside ft2v1. Rookie mistake!
@@Edin21 If you are willing to tinker and have a steady hand, you can scrape the silk screen on the top side near the apu, this is an alternative post point. If worst comes to worse, you can use a corona post fix adapter to get access to the post point.
@@hardcoregamer685 I will take a look tomorrow and get back to you as it’s late here. I appreciate the advice!
Yes, this method doesn't require those points so would be a good alternative. Although, it does still require many points the same size, so practise your soldering first.
so you can see how good and complex the exploits of the past were
already more we will have this on today's consoles
Yeah, glitch chips aren’t even needed anymore. I just uploaded this just in case someone didn’t want to try the harder RGH3 mod or damaged their PLL point.
can i use raspberry pi pico instead of nand-x? and how to connect ace v3 to rashberry pi pico?
You cant. pi pico does not support glitch chip flashing right now.
Will this still work if I'm using Picoflasher?
PicoFlasher can’t flash glitch chips, so you’ll need a different flasher for this method.
@@TheModSmithI found a guy who made a Programmer for Pico but I have literally no clue at all how to use it. th-cam.com/video/eC3C9Ab8bRU/w-d-xo.htmlsi=_9ViuTa2zxDeSGdZ you would know much more about glitch chips than me so could you make a video on how to use this on the ace?
Hello guys, I screw up with the PLL point, and I have to follow this tutorial now... Can I use the JR programmer instead, and if yes,is the process harder or different from x flasher to program the ace v3? Thank you
You can use the JRProgrammer and the process is the same.
Thank you very much for your quick response!
I just RHG my Xbox with your tutorial, thank you very much!!!!
Wait regardless if you screw up the pll using the 2 wires rgh methid this will still work?@TheModSmith
Is this better than RGH3?, I have a Xbox 360 trinity with same ace v3 chip
RGH3 is better, but this is an easier install to do.
No need for the massive solder blob on the av/hdmi
There is literally a GND point you can solder to
I'm aware, but this guide is meant to cover the easiest installation possible.
@@TheModSmith fair play mate makes sense it can be tricky to get solder on the point sometimes
I aint doing this
Please close the door on the way out!
Hey man, please can you give me the best contact method for you? discord, email?