I appreciate your time... But I. Wud make this simple.... First just heat up the engine then open the cover... Then start again turn the gas a bit... Close air screw fully...now turn a bit more gas and now just start turning anti clock wise the air screw... When the rpm raises high.. stop turning and that's it... This is the correct way to tune... Stop at High rpm... And see how crisp the response is... Do it and reply..
@ I have mileage problem with my Jawa 71 model, I have loosen the horizontal air screw to the 2.5 turns, earlier the mechanic had set it to 1/2 turn but the mileage was just 20km. What is correct setting for mileage and for idling. Note: The firing should be slow and late firing, this is my requirement, how do I set it Hari Anna?
@@hariprasadkathyayani thank you kindly for getting back to me. i have it set at 1/2 turn and needle clip set in 3 rd groove from the top. in your video on setting timing advance you advise to set by lining edge of terminal connector to edge of cylinder fins approximately 12oclock to 6 oclock position. With this setting does your bike run hotter due to advance? if so would you think we may need to go up to the fourth groove to increase fuel level? Please forgive me questions. I look forward to your reply. Regards Keith
Hi Ashitosh, Tighten main screw all the way in, Do not force it be gentle until it stops then loosen it 1/2 turn. Right hand tighten left hand loosen. Check spark plug colour after riding for a few days to see colour and adjust main screw 1/4 turn or more or lesser, Should be between 1/4 turn to 3/4 turn depending on your bike. Hope this helps. I am sure Hari maybe able to explain much better than me. Regards Keith
Hi Lakshith The idle screw is on the bottom beside the main mixture screw. Tightening it will increase engine speed and loosening it will decrease engine speed.
![[TH] 2024 PMWC x EWC Group Stage Day 2 | PUBG MOBILE WORLD CUP x ESPORTS WORLD CUP](http://i.ytimg.com/vi/vwIQyCmNIBU/mqdefault.jpg)
I appreciate your time... But I. Wud make this simple.... First just heat up the engine then open the cover... Then start again turn the gas a bit... Close air screw fully...now turn a bit more gas and now just start turning anti clock wise the air screw... When the rpm raises high.. stop turning and that's it... This is the correct way to tune... Stop at High rpm... And see how crisp the response is... Do it and reply..
@ I have mileage problem with my Jawa 71 model, I have loosen the horizontal air screw to the 2.5 turns, earlier the mechanic had set it to 1/2 turn but the mileage was just 20km. What is correct setting for mileage and for idling.
Note: The firing should be slow and late firing, this is my requirement, how do I set it Hari Anna?
Hi Hari
The mixture screw is set for 1/4 turn out or 1/2 turn? Also would you have for 1969 jaws 353 250cc semi auto clutch mechanism?
Hi
1/2 turn.
Very soon I will upload auto clutch cam mechanism
@@hariprasadkathyayani thank you kindly for getting back to me. i have it set at 1/2 turn and needle clip set in 3 rd groove from the top. in your video on setting timing advance you advise to set by lining edge of terminal connector to edge of cylinder fins approximately 12oclock to 6 oclock position. With this setting does your bike run hotter due to advance? if so would you think we may need to go up to the fourth groove to increase fuel level? Please forgive me questions. I look forward to your reply. Regards Keith
@@keithmason3461
Very soon I upload all videos
Plz tell me how set main screw of carborator
Hi Ashitosh, Tighten main screw all the way in, Do not force it be gentle until it stops then loosen it 1/2 turn. Right hand tighten left hand loosen. Check spark plug colour after riding for a few days to see colour and adjust main screw 1/4 turn or more or lesser, Should be between 1/4 turn to 3/4 turn depending on your bike. Hope this helps. I am sure Hari maybe able to explain much better than me. Regards Keith
Hello friend, I have a jawa. Can you making video for exilator smooth rotation setting. Thank you.
Ok
Yezdi cl 2 me engine oil kaun sa num. Ka dalna chahiye
Gear oil castrol 20W 49 CF4. 900 mL
Patrol mixture castrol 2t , 40 mL per liter
Can I know how to set idling in yezdi roadking
Hi Lakshith The idle screw is on the bottom beside the main mixture screw. Tightening it will increase engine speed and loosening it will decrease engine speed.
How much approximate anticlock wise turn of air screw of cl2 pacco carburator
P43 or p47y
@@hariprasadkathyayani p43
Sir your voice is not clear, lot of disturbance due to noise, please explain once the bike is off
Plz tell how to set carborator fuel and air mixture
Contact me on 9908220222
@@sudarashansen9177 Ok sure
bro the audio is not clear
Ok I will upload good voice