You sound like me! I have been trying to find a good washer for my mother. Her older LG has had 3-4 repairs in the last 2 years and now something else has broken. Its time for a new one and she wants a top loader. I am just going to get a Whirlpool.
@@itsnoahonfire I got a “used” Whirlpool (it was only from 2022) at a good used appliance store and it’s been good so far. Cost $650 for both washer and dryer but because there isn’t warranty I am a bit nervous if anything goes wrong. But so far it’s been good.
I have this exact washer. The full model number of mine is WTW4816FW3, which I'm guessing means it's the third revision of this machine. It's a good performer if one understands its little quirks, of which there are a few. Here are some tips I've learned: 1. Don't use the normal cycle for anything other than possibly a half load or less. This is the eco cycle, so it uses much less water than the others even on the auto-sense setting, and it does not allow for a deep wash, which I believe is necessary when washing full loads in this machine because of the design of the agitator which rolls the laundry through the wash water. The normal cycle also has a pitiful spray rinse, but one can negate that by selecting the extra rinse which will add a full deep rinse, but at the same lower water level as the wash. It's a good cycle for lightly soiled loads of about a half tub or less, but anything more than that, I'd use something else. 2. Piggy-backing off of the last tip, always use the deep wash option for full loads. In my opinion, the auto sensor doesn't put in enough water for full loads, especially full mixed loads because the auto sensor works on how heavy the clothes are, not how many clothes are in the drum. So, one might end up with half a tub of water to wash a full tub of clothes, which just leads to them being bunched up and thrashing back and forth against the agitator. Deep wash will give you a full tub of water so full loads can then turn over effortlessly. The agitator in this machine does a great job if it has enough water to work properly. I've seen lots of reviewers saying they have to use the bulky cycle to get enough water in the machine, but that is not so. I'd use deep wash before using bulky because bulky defaults to a low-speed spin, no bueno for heavy items. For a full tub of everyday clothes, my go-to selections are heavy duty cycle, soil level knob set to light so the agitation isn't quite as long, warm water, and deep wash. If a fast wash time is important, one can use quick wash, but I found for myself that the final spin wasn't long enough for large loads. 3. DON'T OVERLOAD! This is imperative. This machine can't handle it. One can audibly hear the motor and gears straining during an overload condition, I speak from experience. One or two times of this happening corrected me of that behavior. Loosely packed, dry clothes to the top row of holes in the tub is the most you should put in this washer. Also, as stated in the video, balancing the load correctly is important because of the hanging suspension. If the load is out of balance at all, the machine will bang the tub against the sides of the cabinet and let me tell you, that is LOUD! I guess I kinda wrote a novel, LOL, but I hope it helps others. It really is a good washer if one knows how to use it properly.
Thank you! I screenshot your tips. I just bought this model, after cancelling the order on two others I read too many bad things about. This has been quite a nightmare shopping for a new washer in this weird era of poor quality, "high efficiency", and computerized junk. I hope and pray I'm going to love this one, and that it will be a good one, it will arrive Monday. 🙏
I think you made an overall good choice. Like I said, it's not perfect, but it does get the job done well if you know how to use it correctly. Also, I'm going to tell you now it requires some patience. If you're coming from an old pre-2010 or so machine, you're probably used to cycle times clocking in at around 30-40 minutes. There are some cycles on this one, like quickwash using its default settings, that'll do this, but I'd avoid that if I were you except for small light loads. A full load with the settings that I believe give the best performance takes around an hour. For example, I was curious to know exactly how long my heaviest loads take so I timed it on a full load of towels a few days ago, set on superwash, medium soil level, hot water, one rinse with softener. The cycle clocked in at 70 minutes. People find this out and feel like no way, I'm not waiting that long, my old washer took blah blah quicker time to complete a cycle, but honestly, no washer on the market, except the LG front loaders that have the turbo wash feature or perhaps Speed Queen, are going to do an effective job in 30 minutes. They just aren't designed that way. So I guess my other piece of advice is don't hang around wondering when the cycle is going to finish. Just use my recommended settings and find something else to do while it washes. The hour will go by before you even know it. :D Good luck with it. I still like mine. If you have any questions, feel free to reply to this thread and I'll do my best to help.
@@rynerobinson903 thank you so much. I'm actually really loving this washing machine so far! I don't mind waiting a little longer for loads to wash (I live alone, so I only have have to wash for myself), and honestly, the cycles don't seem to be too long to me. My clothes are getting cleaner than they've been getting in a long time, but the cycles seem to be gentle on them. I do appreciate your tips so much, they've come in handy. I think this model was the best choice, and I got it on a great sale at Lowe's for $489. I couldn't be more pleased.❤️
I have trouble it’s not spinning clothes out they still wet after rinse it goes to wash and sits there we have to manually put on drain and spin then it will drain ,spin amend end this is second one in less than a month actually 3rd. First one would not drain and rinse properly 2nd came with a broke pan hose this one same as first is not draining and spinning properly it goes to wash we have to manually drain and spend this one will probably be going back also
Man I appreciate you sharing your knowledge and opinions on these appliances. I’m young , and about to try to get my first house soon. Appliances aren’t cheap and I don’t wanna buy a piece of junk.
This is definitely one of the best washers out there for the money. It’s one of the last washers available with the deep cleaning dual action agitator and a true full basket of water. The only other washer that will perform better is the Maytag Commercial Model MVWP586GW which is almost twice the price but definitely worth it, it even comes with a full 5 year warranty. But for the money the Whirlpool WTW4816FW is definitely a bargain. The only negative is that it is a Lowes only machine, but Lowes often has them on sale.
Still surprises me that Whirlpool has never changed the basic Top-Filter dryer design since the 1950s, beside the smaller 27" one with the Filter below the door.
My Maytags are monkey crap. On the dryer, it makes a buzz when it is done and has a crooked logo badge. The drum is off balance on the washer. There are also scratches on the dryer drum!! We bought these at the beginning of this year! Thanks a lot, Whirlpool.
We've had our Samsung washer for 7yrs they are supposed to be junk, the only things we replaced were a water inlet valve and balance rods parts come to around $60.00 and easy to replace.
Yup, I think I have settled on the Whirlpool unit as well. Mind you, here in Canada that unit is around $725 and we can not purchase Speed Queen as I can't find a dealer up here. What we now need is a hacker to design a cheap computer board for us and let's find better pumps n parts for these things too.
Had this washer about 4 years. The metal gear that turns the plastic agitator seems to have corroded and the cost of purchasing a new agitator and gear assembly was not worth repairing. Going a different route on the next one.
I have this washer and I like it fine. Mine came from Lowes and does say Whirlpool Corp of Quebec Canada. It doesn't matter to me where it was built, the US or Canada. But it does to you, you might want to ask.
Is this model required to use HE detergent? I just looked at the same model today at a local Lowes only difference is the last digit of the SN is 2 instead of 3. Not sure what difference is. I wish it was a convental washer not HE. But salespeople are leading me to believe that all the new washers are HE. I come from using a Kenmore Series 80 that died, now I have to replace it with something new. I'm a bit out of my element.
I feel like I made it out like a thief, I got a 12 yr old whirlpool from an old lady for 75 bucks and she got some new LG crap at brandsmart🙃. My LG ironically just broke and that is why I bought it.
I have this very model. The only one that is carrying it I think is Lowe’s. That’s where I got mine. I have a Maytag commercial coming this coming week. I want to have a few agitator top load washers before they go completely bye-bye.
Always had good luck with Whirlpool/Kenmore appliances. Bought a GE washer/dryer in 2016. Has been stellar past 7+ yrs. My kitchen appliances are all LG. Kind of mediocre.
For a couple fine buy the budget washers . But as a family of five they don’t hold up to us . We bought an expensive GE set then and had both boards fry at 8 months old . And guess what the warranties are not worth the paper they are written on . We now have expensive speed queens .
Story about a lady who found a computer board at $60. Meaningless. The problem: the computer boards are known for going out, the pressure swtiches as well. Of course folks should choose this over Samsung, LG, and Hotpoint. Known garbage for years, could care less if 'they're getting better'. Maytag or Whirlpool a better/safer choice and lower parts cost with more availability should issue arise. Great tips of course but exactly reasons you might want to avoid the lowest range Whirlpools, or any other brand.
I have 7 children and our washer just went out. I need something reliable and can’t afford a speed Queen. Does this only come in the smaller sizes I’ve seen online? Wondering if I’m crazy for considering getting such a small washer.
If you have a tight budget, and are willing to go for used machines, I would get a used LG front loader. I’ve used 6 different models, and they’re all great.
Whirlpool is awful. I purchased this exact model and upon install and running water the washer leaked through the drum. Almost flooded my basement. Luckily the delivery guys were still there as they took it right away and I bought an LG.
I personally prefer front loaders. We do so much laundry that I don’t think a washer like this would be big enough for us. We are a family of 4 that does about 20 loads a week. Sometimes, I think our 4.5 cu.ft Whirlpool front loader isn’t big enough.
I think that previous video with the wonderful sound of clothes actually getting clean in the Speed Queen TR7 in wash mode might be from his own laundry room. 😊 LOVE LOVE MY TR7. The problems I had with previous Maytag and LG-so glad to say goodbye to that junk.
Meh...I coughed up the cash and bought a Speed Queen. It will still be working when I'm dead of old age but it is the last washer I'll ever have to buy.
and the motors in these fail and is over engineered... why can't the industry go back to a simple direct drive system......I had a GE that only lasted 10 years and then the motor went onto a lockout mode and had to be reset, resetting the motor did not work..... and the computer board is a problem also.....I hate the new machines. I have a whirlpool from the 90's in almond and it works awesome! it has the same agitator in it also!
Unfortunately they are all junk they don’t last more than two years the electronic balancing breaks. I bought a set from the early 90’s they have been slightly refurbished and have been going for 24 years.
I would never buy this i had a similar one and only lasted 5 years i replaced it with a used old kenmore 90 series ( iwas a bit nervous it was just a waste of money) but it actually worked that thing washes like if it just came out of the store brand new and its 23 years old but not sure how far it will go from there literally no problems execpt the drain pump once needed to change but overall any used kenmore or wirlpool old school washer is good people who actually buys this washer just have money to spend every few years thats what companies do make faulty appliances so u can spend more money
![[LIVE] : ONE ลุมพินี 88 | คู่เอก "ป้อมเพชร vs อัสลามจอน"](http://i.ytimg.com/vi/1ZqTVVbMgbo/mqdefault.jpg)
I’m so overwhelmed from reading about washers and dryers for the past 30 hours I’m just gonna buy this one
Same! My head is swimming, soooo many variables and reading reviews.. I’m going with this one too
You’ll regret it sooner or later..
You sound like me! I have been trying to find a good washer for my mother. Her older LG has had 3-4 repairs in the last 2 years and now something else has broken. Its time for a new one and she wants a top loader. I am just going to get a Whirlpool.
@@itsnoahonfire I got a “used” Whirlpool (it was only from 2022) at a good used appliance store and it’s been good so far. Cost $650 for both washer and dryer but because there isn’t warranty I am a bit nervous if anything goes wrong. But so far it’s been good.
@@Ikey04-ge9gy I mean if you take good care of it, and get the one with the agitator then its decent. The dryer is almost perfect
I have this exact washer. The full model number of mine is WTW4816FW3, which I'm guessing means it's the third revision of this machine. It's a good performer if one understands its little quirks, of which there are a few. Here are some tips I've learned:
1. Don't use the normal cycle for anything other than possibly a half load or less. This is the eco cycle, so it uses much less water than the others even on the auto-sense setting, and it does not allow for a deep wash, which I believe is necessary when washing full loads in this machine because of the design of the agitator which rolls the laundry through the wash water. The normal cycle also has a pitiful spray rinse, but one can negate that by selecting the extra rinse which will add a full deep rinse, but at the same lower water level as the wash. It's a good cycle for lightly soiled loads of about a half tub or less, but anything more than that, I'd use something else.
2. Piggy-backing off of the last tip, always use the deep wash option for full loads. In my opinion, the auto sensor doesn't put in enough water for full loads, especially full mixed loads because the auto sensor works on how heavy the clothes are, not how many clothes are in the drum. So, one might end up with half a tub of water to wash a full tub of clothes, which just leads to them being bunched up and thrashing back and forth against the agitator. Deep wash will give you a full tub of water so full loads can then turn over effortlessly. The agitator in this machine does a great job if it has enough water to work properly. I've seen lots of reviewers saying they have to use the bulky cycle to get enough water in the machine, but that is not so. I'd use deep wash before using bulky because bulky defaults to a low-speed spin, no bueno for heavy items. For a full tub of everyday clothes, my go-to selections are heavy duty cycle, soil level knob set to light so the agitation isn't quite as long, warm water, and deep wash. If a fast wash time is important, one can use quick wash, but I found for myself that the final spin wasn't long enough for large loads.
3. DON'T OVERLOAD! This is imperative. This machine can't handle it. One can audibly hear the motor and gears straining during an overload condition, I speak from experience. One or two times of this happening corrected me of that behavior. Loosely packed, dry clothes to the top row of holes in the tub is the most you should put in this washer. Also, as stated in the video, balancing the load correctly is important because of the hanging suspension. If the load is out of balance at all, the machine will bang the tub against the sides of the cabinet and let me tell you, that is LOUD!
I guess I kinda wrote a novel, LOL, but I hope it helps others. It really is a good washer if one knows how to use it properly.
Thank you! I screenshot your tips. I just bought this model, after cancelling the order on two others I read too many bad things about. This has been quite a nightmare shopping for a new washer in this weird era of poor quality, "high efficiency", and computerized junk. I hope and pray I'm going to love this one, and that it will be a good one, it will arrive Monday. 🙏
I think you made an overall good choice. Like I said, it's not perfect, but it does get the job done well if you know how to use it correctly. Also, I'm going to tell you now it requires some patience. If you're coming from an old pre-2010 or so machine, you're probably used to cycle times clocking in at around 30-40 minutes. There are some cycles on this one, like quickwash using its default settings, that'll do this, but I'd avoid that if I were you except for small light loads. A full load with the settings that I believe give the best performance takes around an hour. For example, I was curious to know exactly how long my heaviest loads take so I timed it on a full load of towels a few days ago, set on superwash, medium soil level, hot water, one rinse with softener. The cycle clocked in at 70 minutes. People find this out and feel like no way, I'm not waiting that long, my old washer took blah blah quicker time to complete a cycle, but honestly, no washer on the market, except the LG front loaders that have the turbo wash feature or perhaps Speed Queen, are going to do an effective job in 30 minutes. They just aren't designed that way. So I guess my other piece of advice is don't hang around wondering when the cycle is going to finish. Just use my recommended settings and find something else to do while it washes. The hour will go by before you even know it. :D
Good luck with it. I still like mine. If you have any questions, feel free to reply to this thread and I'll do my best to help.
@@rynerobinson903 thank you so much. I'm actually really loving this washing machine so far! I don't mind waiting a little longer for loads to wash (I live alone, so I only have have to wash for myself), and honestly, the cycles don't seem to be too long to me. My clothes are getting cleaner than they've been getting in a long time, but the cycles seem to be gentle on them. I do appreciate your tips so much, they've come in handy. I think this model was the best choice, and I got it on a great sale at Lowe's for $489. I couldn't be more pleased.❤️
I have trouble it’s not spinning clothes out they still wet after rinse it goes to wash and sits there we have to manually put on drain and spin then it will drain ,spin amend end this is second one in less than a month actually 3rd. First one would not drain and rinse properly 2nd came with a broke pan hose this one same as first is not draining and spinning properly it goes to wash we have to manually drain and spend this one will probably be going back also
Many new machines won't let you manually choose the water level. I hate that. They use sensors and they aren't always accurate.
Man I appreciate you sharing your knowledge and opinions on these appliances. I’m young , and about to try to get my first house soon. Appliances aren’t cheap and I don’t wanna buy a piece of junk.
I hope it helps. Spend your money on raising great kids... not on junk!
What's the model number for the dryer
This is the set I bought for my apartment. Specifically for the dual action agitator. I’m glad I made a good choice.
This is definitely one of the best washers out there for the money. It’s one of the last washers available with the deep cleaning dual action agitator and a true full basket of water. The only other washer that will perform better is the Maytag Commercial Model MVWP586GW which is almost twice the price but definitely worth it, it even comes with a full 5 year warranty. But for the money the Whirlpool WTW4816FW is definitely a bargain. The only negative is that it is a Lowes only machine, but Lowes often has them on sale.
Thank you for taking the time to make this video. Great info, and I appreciate your support of products made in the USA.
Still surprises me that Whirlpool has never changed the basic Top-Filter dryer design since the 1950s, beside the smaller 27" one with the Filter below the door.
And it works great
My Maytags are monkey crap. On the dryer, it makes a buzz when it is done and has a crooked logo badge. The drum is off balance on the washer. There are also scratches on the dryer drum!! We bought these at the beginning of this year! Thanks a lot, Whirlpool.
We've had our Samsung washer for 7yrs they are supposed to be junk, the only things we replaced were a water inlet valve and balance rods parts come to around $60.00 and easy to replace.
I have the same dryer on 220v . The best one !!!👍👌
Yup, I think I have settled on the Whirlpool unit as well. Mind you, here in Canada that unit is around $725 and we can not purchase Speed Queen as I can't find a dealer up here. What we now need is a hacker to design a cheap computer board for us and let's find better pumps n parts for these things too.
I like Speed Queen, but I keep hearing that the TC5 doesnt get clothes that clean. It is very durable though. I leaning towards Maytag Commercial 586.
The opinions on Speed Queen vs Maytag commercial are either they are junk or they are amazing! Not sure what to believe!
Always goes wrong in the suspension roods at 2 years of use starts banging around and the actuator or bearings go out easily as well
I have this one, just died. It doesn’t agitate. It lasted 8 years.
I see a lot of the lowest price washers now have the crappy fake stainless steel tubs. I'd rather have a white one like this.
Had this washer about 4 years. The metal gear that turns the plastic agitator seems to have corroded and the cost of purchasing a new agitator and gear assembly was not worth repairing. Going a different route on the next one.
Yeah, about $120 per year investment
U should get a used kenmore 90, 80, 70, 60 or which ever series u want as long as its not newer model washers
i've had these before, they were pretty good.
I have this washer and I like it fine. Mine came from Lowes and does say Whirlpool Corp of Quebec Canada. It doesn't matter to me where it was built, the US or Canada. But it does to you, you might want to ask.
We bought one used almost 10 years ago for like 40 bucks , it finally quit a couple weeks ago so we bought a new one today , with the dryer .
Would you buy this washer & dryer refurbished for $500 together or the Whirlpool WTW4955 washer & dryer for $900 scratch-&-dent?
i have this washer and the motor had to be replaced after 13 months and now at two years and a couple months it need a circuit board😮
Is this model required to use HE detergent? I just looked at the same model today at a local Lowes only difference is the last digit of the SN is 2 instead of 3. Not sure what difference is. I wish it was a convental washer not HE. But salespeople are leading me to believe that all the new washers are HE. I come from using a Kenmore Series 80 that died, now I have to replace it with something new. I'm a bit out of my element.
I see there’s many different cubic feet sizes for these, what does that mean??
I feel like I made it out like a thief, I got a 12 yr old whirlpool from an old lady for 75 bucks and she got some new LG crap at brandsmart🙃. My LG ironically just broke and that is why I bought it.
I would prefer a used Whirlpool Direct Drive washing machine rather than the new Vertical Modular Washers.
These aren’t really that new anymore. They’ve been around 13 years now.
I have this very model. The only one that is carrying it I think is Lowe’s. That’s where I got mine. I have a Maytag commercial coming this coming week. I want to have a few agitator top load washers before they go completely bye-bye.
Always had good luck with Whirlpool/Kenmore appliances. Bought a GE washer/dryer in 2016. Has been stellar past 7+ yrs. My kitchen appliances are all LG. Kind of mediocre.
It's a washer & dryer. You're cleaning dirty clothes. Why would anyone go out & spend crazy $$$ on a set? I buy American made Whirlpool anyday.
For a couple fine buy the budget washers . But as a family of five they don’t hold up to us . We bought an expensive GE set then and had both boards fry at 8 months old . And guess what the warranties are not worth the paper they are written on . We now have expensive speed queens .
All of the machines are made to break down, speed queen is expensive yes but they are very durable and will last longer than these will
should i buy this set or GE around the same price? Im thinking ge but let me know pleas im buying today
Where I can buy speed queen washer? For home
I just purchased this and the matching electric dryer set
This or an Amana??
I went with GE
Story about a lady who found a computer board at $60. Meaningless. The problem: the computer boards are known for going out, the pressure swtiches as well.
Of course folks should choose this over Samsung, LG, and Hotpoint. Known garbage for years, could care less if 'they're getting better'.
Maytag or Whirlpool a better/safer choice and lower parts cost with more availability should issue arise.
Great tips of course but exactly reasons you might want to avoid the lowest range Whirlpools, or any other brand.
This one’s a rental house special lol, landlords just buy the cheapest new ones.
I have 7 children and our washer just went out. I need something reliable and can’t afford a speed Queen. Does this only come in the smaller sizes I’ve seen online? Wondering if I’m crazy for considering getting such a small washer.
Kenmore 80 Series
If you have a tight budget, and are willing to go for used machines, I would get a used LG front loader. I’ve used 6 different models, and they’re all great.
You can buy a Japanese style mini washer for like $250
Anything but newer model washers
Whirlpool is awful. I purchased this exact model and upon install and running water the washer leaked through the drum. Almost flooded my basement. Luckily the delivery guys were still there as they took it right away and I bought an LG.
Please make video's on BOSCH SIEMENS Front load
I Recently purchase SIEMENS 8Kg Front load WG34A20SIN/2023
Overpriced....
@@steveludwig4200
Washing machine is one time investment if you are getting quality product it’s totally worth to buy
Solid video man 👍🏻
Can I wash a king comforter?
Getting a house soon and will be getting these. But i need help for a fridge option. Any suggestions?
Yea go with the whirlpool
Thanks, Great Info..
I have this washer! Good one too!
Can a queen size comforter fit and wash well?
don't put a comforter in your washing machine, it's not worth it. Take it to the laundromat where they have bigger machines.
Thanks!
I personally prefer front loaders. We do so much laundry that I don’t think a washer like this would be big enough for us. We are a family of 4 that does about 20 loads a week. Sometimes, I think our 4.5 cu.ft Whirlpool front loader isn’t big enough.
Is this your home? No speed queen?
Not my home
I think that previous video with the wonderful sound of clothes actually getting clean in the Speed Queen TR7 in wash mode might be from his own laundry room. 😊 LOVE LOVE MY TR7. The problems I had with previous Maytag and LG-so glad to say goodbye to that junk.
Meh...I coughed up the cash and bought a Speed Queen. It will still be working when I'm dead of old age but it is the last washer I'll ever have to buy.
and the motors in these fail and is over engineered... why can't the industry go back to a simple direct drive system......I had a GE that only lasted 10 years and then the motor went onto a lockout mode and had to be reset, resetting the motor did not work..... and the computer board is a problem also.....I hate the new machines. I have a whirlpool from the 90's in almond and it works awesome! it has the same agitator in it also!
Unfortunately they are all junk they don’t last more than two years the electronic balancing breaks. I bought a set from the early 90’s they have been slightly refurbished and have been going for 24 years.
I don’t like the way these top loaders waste water. I prefer a front loader
I just bought a Hotpoint…..489$. 2024.
I would never buy this i had a similar one and only lasted 5 years i replaced it with a used old kenmore 90 series ( iwas a bit nervous it was just a waste of money) but it actually worked that thing washes like if it just came out of the store brand new and its 23 years old but not sure how far it will go from there literally no problems execpt the drain pump once needed to change but overall any used kenmore or wirlpool old school washer is good people who actually buys this washer just have money to spend every few years thats what companies do make faulty appliances so u can spend more money
None fill all the way tho
I hate those machines they are awful I would never buy them
Cassin Tunnel
I have this washer and it’s dog shit….
Hand me batao