D16 TURBO SPEED FACTORY SAVAGE CAM AND SF CAM GEAR DEGREE/INSTALL

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ม.ค. 2025

ความคิดเห็น • 27

  • @notone4029
    @notone4029 5 หลายเดือนก่อน +3

    Been a Hot minute since any new videos. Good to see you post finally. Yeah personally had BAD Luck with Skunk2 I mean Junk2 . Sounds like your old Skunk2 cam gear was sub par as well. Can’t go wrong with SpeedFactory though , BEST of the BEST !!! 👍🏻🔥🔥🔥🔥

  • @tsaintt691
    @tsaintt691 หลายเดือนก่อน +1

    Great videoI have a question what kind of chemicals I have to put to the single cam before I put it ?

    • @schmikels_garage
      @schmikels_garage  หลายเดือนก่อน

      @@tsaintt691 engine assembly lube, I used a Lucas racing assembly lube. But any assembly lube should work

  • @peterbryant3584
    @peterbryant3584 23 วันที่ผ่านมา

    Great video great explanation nice work

    • @schmikels_garage
      @schmikels_garage  23 วันที่ผ่านมา

      @@peterbryant3584 thanks a bunch!!

  • @LouieLouGarage88
    @LouieLouGarage88 5 หลายเดือนก่อน +3

    OOOO i get so excited for Schmikle videos

  • @lynnsentivany269
    @lynnsentivany269 5 หลายเดือนก่อน

    Nice to see a new video!!!!

  • @Tulski_RR1184
    @Tulski_RR1184 5 หลายเดือนก่อน +2

    🤙🤙🤙

  • @gxwsr4665
    @gxwsr4665 5 หลายเดือนก่อน +1

    I need some help with my camshaft, I took off the stock camshaft at tdc marks with the cam gear and when I try to install the street savage camshaft with the golden eagle cam gear the cam gear keeps going off tdc. Help me I’m new to this

    • @schmikels_garage
      @schmikels_garage  5 หลายเดือนก่อน

      @@gxwsr4665 what do you mean that it goes off tdc when with the golden eagle gear? The cam is installed and you go to put the gear on and the timing marks or off? If so can you just turn the cam or if that’s what is happening can you put the stock gear on with the cam already installed and are the timing marks lined up? What d series are you installing the cam into? Also if you are not using a z6 cam gear it won’t work the savage cam is a z6 so if that golden eagle gear is a Y8 gear that’s your problem.

    • @gxwsr4665
      @gxwsr4665 5 หลายเดือนก่อน

      My issue was that I was installing the street savage cam with the golden eagle cam gear on the camshaft already. And when I tried to put the rocker arm assembly on it wouldn’t sit flush and the cam gear would turn every time I try to make it sit flush, because aren’t you supposed to have the cam gear at tdc then tighten the rocker arm assembly down. Or am i doing it wrong the whole time

    • @schmikels_garage
      @schmikels_garage  5 หลายเดือนก่อน

      @@gxwsr4665 yeah that’s what ya do but it will turn when it’s tightened that’s fine just once the rocker arms are all torqued just rotate the cam to tdc it only moves a little and isn’t a big deal it won’t hurt anything when it moves

    • @schmikels_garage
      @schmikels_garage  5 หลายเดือนก่อน

      @@gxwsr4665 one other thing I just thought of that I didn’t mention is the adjusters for the valves on the rocker arms should be all the way out that will help with it turning the cam but more importantly when you are torquing it there is less cha be if snapping the cam from u even pressure

  • @frias2287
    @frias2287 5 หลายเดือนก่อน +1

    Nice 👍 👍 👍

  • @h3xd3m0n9
    @h3xd3m0n9 3 หลายเดือนก่อน

    I'm planning to get the same cam after I replace my split block lol you ever split a y8 block before ?

    • @schmikels_garage
      @schmikels_garage  3 หลายเดือนก่อน

      @@h3xd3m0n9 dang!! Nah I haven’t split a block yet. How much power did it have to split it? Deff recommend this cam it woke my engine up so much!

    • @h3xd3m0n9
      @h3xd3m0n9 3 หลายเดือนก่อน

      @@schmikels_garage I never had it on a dyno but based off fuel quantity 450 at the crank. I was using a ported y8 head and a y7 cam running it at 37psi. I honestly just think it's a block lottery or fatigue I've been running this engine for almost three years and not nice to it

    • @schmikels_garage
      @schmikels_garage  3 หลายเดือนก่อน

      @@h3xd3m0n9 that makes sense only can last so long haha, were the internals able to be reused?

    • @h3xd3m0n9
      @h3xd3m0n9 3 หลายเดือนก่อน

      @@schmikels_garage I haven't taken it apart yet but it runs fine just has coolant pouring out from front to back so I'm gonna assume so. How's the new cam feel have yo taken it for a good blast yet ? I'm hoping to take the engine apart this weekend and going to pick up the new engine today hopefully the rockers are in good shape and not groved like last ones forcing me to use the y7 guts

    • @schmikels_garage
      @schmikels_garage  3 หลายเดือนก่อน

      @@h3xd3m0n9 oh nice!! The cam deff rips it made a huge difference over the delta grind I had it early prob a 50+who gain if not more and deff help the spool a lot really glad I made the switch!! Ya know I never thought about using the y7 rocker arms if the other or worn out that’s good to know cause I have a sparey7 head I prob could have used this rockers instead if having to buy a used set haha

  • @beethao5578
    @beethao5578 5 หลายเดือนก่อน

    Bro u should build a high comp d16z6

  • @GRASSINCLASS
    @GRASSINCLASS 5 หลายเดือนก่อน

    HI SCHMIKELS dint See an email or a way to contact you ? . do you have a way ?

    • @schmikels_garage
      @schmikels_garage  5 หลายเดือนก่อน

      @@GRASSINCLASS my email is schmikelbays@gmail.com I didn’t realize I didn’t have those in my profile. Thanks for letting me know I’m going to add my email and my IG and Facebook links sometime soon.