Kenmore Top-Load Washer Clutch Replacement Part WP8299642
ฝัง
- เผยแพร่เมื่อ 14 ต.ค. 2024
- Buy part WP8299642 now: www.repairclin...
This video provides step-by-step repair instructions for replacing the clutch on a Kenmore Top-Load washing machine. The most common reason for replacing the clutch is if the tub will not spin or agitate.
Additional washing machine repair, troubleshooting tips, help with finding your model number and part replacement videos can be found on our website:
www.repairclini...
All of the information for this clutch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers, 5/16" socket, 9/16" socket, 1/4" socket
Buy part #S144CB now: www.repairclin...
Buy part #P204CB now: www.repairclin...
Buy part #N516CB now: www.repairclin...
Buy part #38054 now: www.repairclin...
Buy part #N140CB now: www.repairclin...
Buy part #420 now: www.repairclin...
Connect With Us!
plus.google.co...
/ repairclinic
/ repairclinic
/ repairclinic
Join our free VIP email list for discounts and money-saving tips: tinyurl.com/pnn...
Check out our blog: www.DIY.RepairC...
Don't forget to like and comment on this video, and subscribe to our channel!
![โรงเรียนดัดสันดาน นักเรียนเถื่อน..!! [โรงเรียนไดเม่]](http://i.ytimg.com/vi/vRKPeXn4Fl4/mqdefault.jpg)
Saved a fortune watching these videos to repair our washer (Whirlpool ultimate care 2 (11) ten years old). My husband who really has no hands on repair experience managed to follow them. We replaced the clutch kit search for (285753A) and the motor coupler, search for (275753) If you only need the clutch band off it search (3951993 band only) We also replaced the agitator dogs search for (80040) and looked at the door switch which we disconnected to see if that worked. Typically it was the last thing we tried which was the motor coupler! Persevere these are simple machines and not much can go wrong, mine has now had a full MOT and new replacement parts so should go for another ten years. Hope the product codes help, I spent hours Googling!! xx
This guide was great!
I would note that when sliding the transmission back in, you may need to spin the clutch around until the transmission slides the rest of the way in. It took me several minutes to figure out how to get it to go all the way in. It was stuck a half inch out until I did that.
Thank you your a life saver.
A few things not mentioned in the video:
1) Expect about 1 qt of water to drain out of the machine. Have extra towels and a mop handy.
2)Installing the circular clip on the spacer holding the clutch down: A pair of channel-locks really help in doing this. Squeeze one end of the clip and the other end with the shaft.
3) Installing the motor/clutch coupling (2 plastic pieces and rubber bushing): Seat the first piece on the shaft, and tap it into place. Then put on the rubber bushing. Then put the other plastic piece on the motor. Line up prongs, push entire motor onto bushing, and using a mallet, tap in until tightly together (easier to do when the machine is still on it's back.
4) Motor clips may be difficult; have a crowbar or breaker bar for leverage. Top clip first, then lever motor downward until bottom clip can go on. Clip on pump, THEN tilt mackine forward.
Amazing I am a 65 year old women that is pretty handy at fixing things and with this video I KNOW i can do this A great big thank you.
-I'd like to say thank you very much for this video. It truly came in handy and after watching various other videos for this problem, your video was very straightforward and the steps were extremely beneficial and easy to follow. Thanks again for this video clip. You truly saved me from purchasing a new machine. God Bless!
Why does this feel like an after-school special? Excellent detail. I've ordered the parts today and will definitely have this video on hand when I do the replacement.
This was a great video very detailed and easy to understand . The only issue I had was when I reinstalled the motor it was a bit difficult because it was very low to the floor and the motor a little heavy to hold and keep the spring clips from falling off. I put a six inch block under the frame and then was able to better see where the shaft attached and the spring clips stayed put without falling off. Piece of cake after that. I was wondering if it would be better to attach the motor while the machine was still on it's back.
He should put the motor back while it's laying down. That's how I did it, so much easily
This is so very much appreciated. Many thanks!
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Videos showing setting this type of washer on its back or side should caution that oil will slowly seep out of the gear case vent hole, so the machine should not be left in this posture for a long period of time - for example when a DIY job is interrupted by other matters. Perhaps the vent hole can be temporarily closed with tape if the worker understands where the vent hold is.
It was easy to replace. Thankyou!
thanks for the good video. my washer now works!
Excellent tutorial.
It works! Thanks so much!
Thank you so much for posting this! Saved me a lot of money.
Awesome!
how do I know if my problem is the drive coupler, clutch, or transmission? All three, from what I read online, may be the problem. The top part of the agitator spins, but the bottom won't budge. Removed both and the spindle in the tub is locked up. Did this after I manually drained the entire tub of dirty water. It filled, but there was no spin, so it was stuck in there. And when it tried to spin, I heard a grinding noise.
@@thej762000 thanks for the reply. had this fixed already, though.
Before tipping the washer back apply a wet vac to the discharge hose to remove water.
Very detailed video but OMG how in the world will one remember how to put this thing back together again! Lol.
Wondering what the name of the black rubber belt is you can see at minute 3:40...? I have a broken coupler and that rubber belt but I can't seem to find it anywhere!
Great video thanks... just a note.... next time, when putting the motor and pump back, make sure the machine is tilted and leaning against something......saves back breaking bending lol
Thank you so much! So helpful!
So it does not matter where the brake cam is positioned in relation to the clutch spring?
th-cam.com/video/andudl8IzPQ/w-d-xo.html
Where can i find the half inch square drive ? Cause i cant seem to find one and your help would be nice since im going to be fixing my washing machine and this is the one thing stopping me
A 1/2" socket extension will work. It is 1/2" square. No need for a special socket.
Is it possible I’ve damaged/bent the transmission shaft? I’ve done this several times to fix/check several issues with no problems before but this time after putting back together, the basket shakes violently during spin cycle. I checked the tensioner springs and they seem ok. I’m afraid I left the weight of the transmission on the shaft while sideways and partially pulled out. Everything else went back together and worked fine, I only had trouble pulling the transmission out and had to give it hell before I got it.
Or is it more likely I damaged the stabilizer springs?
I just changed mine and the coupler also and I just ran a load and it spun quickly and seemed to be working it smells strong like burning plastic or something so I don’t know what it could be. It didn’t smell like that before I did it, it was just spinning extremely slow and now it’s spinning fast and seems to be working again but the smell is horrible and it did squeal for a moment before it went to the spin cycle. Any suggestions?
Is the coupler properly aligned
The motor does NOT come off after removing the two bolts and clamps. There must be other screws or bolts holding it?
Has anyone tried this on a kenmore series 80?
I replaced the coupler and clutch and it still won't spin. What else should I look to address part wise?
Agitator dogs
Coupler
Or someone said there could be a sock or something stuck in the tub
That appears to be the same washer as mine. What's the model number?
How do I know is the clutch that I need to replace?
Put you washer on the spin cycle and close the lid. Let it run for a few seconds the open the lid really quick If the tub is not spinning or look like it was spinning then it is the clutch Save your self a headache and replace the motor coupler too. Hope that helps
Cannot find square drives. I'm stupid where do I find these.
Any store that sells automotive or hardware tools.
What are those plastic "cups" with a metal tool inside?
M C I believe they are used for shipping. Then a clip is pulled to release them. Not used for anything afterwards.
you didn't show the alignment of the clutch springs
Awesome video..
Thanks for the information it was my first time ever on a washing machine and i did it yeahhhh ....ty
You didn't show how to deal with the pump drain line and all the water that's still in it. To lay it flat on its back like that, the drain line must be removed and water vacuumed out -- or spilled all over the floor!?
need help changing your under wear too,,,deal with it you winey piss ant
@@billhamilton7524 Wow Bill, are you always a hostile a$$ here on YT?
@@PaulRacko2 sorry sensitive snowflake ,,they take the time to post this how to video and instead of thanks you whine about some water that may have spilled,, ,,careful you may get your hands dirty too
no part number ??
@@repairclinic thanks
@@repairclinic thanks ,,comes with two springs ,,green and blue ,,the blue one is installed ,,does it matter
thanks
@@repairclinic cool thanks
You missed the 2 screws on top side of control panel but well explained
Totally unnecessary to remove the cabinet. You only need to lay the washer on it back.
It sure helps though