With these escooters becoming more powerful and faster It Shud come as standard on all high powered escooters. I have one on mine and its jst so mch smoother
I was also looking into this damper. I believe the $51 is for the damper alone and the $172 is for damper + kit (all the pieces needed) to do full installation on the 10+. So its basically $172 for the 10+ damper
@@FernellyMrFerns Yes you can swap them out for air suspensions but I would probably change them for oil dampening suspension if I ever do decide to change them. They are fine for now. I had a loud creak in the front one after loosen it up a bit the noise went away. I believe the front is 125mm and back is 165mm both are common sizes for mtb suspensions. I'm holding off on the suspensions and damper as I really dont get wobble. Upgrading first to some 160mm rotors and magura mt5e brakes. I will be posting some videos soon.
Steering damper is a completely useless thing and investment! Just tighten the main screw in the middle of the handlebars and tune the rigidity of the handlebar rotation to your liking. Access to the screw is from below, so you don't have to disassemble anything!
Original VSETT Steering Damper Kit ►► s.click.aliexpress.com/e/_9IFUSz
Thank you so much for this very helpful video! My damper came with zero instructions, and without this I would have been lost. Thanks again!
Great video. Was very helpful! People should test those little screws before adding heat. Mine were very loose and had no glue so came straight out.
Good that mine doesn’t wobble. And if someday it will and will install this
Muchas gracias, me sirvió 💯 para ponerlo en mi vsett 10 plus. Thks y saludos desde Colombia 🇨🇴
Yo se lo puse a la mía y siento q me arroja hacia la izquierda y derecha. Te paso lo mismo?
👍 This channel is "dope"!
😊 Thank you
With these escooters becoming more powerful and faster It Shud come as standard on all high powered escooters. I have one on mine and its jst so mch smoother
What is the size of the two small screws you put the glue gun on?
I can't seem to find the right hex wrench. @ 1 is too small and 2 seems too big
I couldn't even get mine out. They probably used too much threadlocker on mine. I tried to heat it and the impact couldn't even get it out.
👍Thank you!
I just got my 10+R yesterday, and can't decide between a damper and exa 291r. What was your reasoning for going with the damper?
Please let me know where I can buy this kit. Cheers.
When can make vsett 9 version
you can see from the turn limit is limited
Are you meant to oil the rod at all or leave it dry?
no dampener on right side? dont like hitting motor cable. and what temperature youre heating on 1:31 ?
On AliExpress there are a few of them for the 10+ but they are different prices.. Why is there a big difference between the $172 and the $51 one?
I was also looking into this damper. I believe the $51 is for the damper alone and the $172 is for damper + kit (all the pieces needed) to do full installation on the 10+. So its basically $172 for the 10+ damper
@@escoot_nyc1651 thank you. Gonna have to get the whole set up then.
@@FernellyMrFerns Yes you can swap them out for air suspensions but I would probably change them for oil dampening suspension if I ever do decide to change them. They are fine for now. I had a loud creak in the front one after loosen it up a bit the noise went away. I believe the front is 125mm and back is 165mm both are common sizes for mtb suspensions. I'm holding off on the suspensions and damper as I really dont get wobble. Upgrading first to some 160mm rotors and magura mt5e brakes. I will be posting some videos soon.
Should u use lock nutt grease ??
@@escoot_nyc1651 ok cool
does this work for vsett 9+ can someone please help me with vsett 9+ i need a steering damper for it would this video work for it and the Product
Ahhh yea... smooooth music.
why would someone design dumper on the same side as motor cable is so that it sqeezes and rubs it when steering?
yah it should be on oposite side
It interferes with the brake cables if on the right hand side. Can add a little cable tie and it mostly sorts the motor cable out.
I also heard that an air suspension can be used to replace the stock suspension the 10+ brings.. U know if there is any truth to this?
Yes of course. Have you ever ridden a mtb
Damn dude you could have showed us where the bushings go and the washers and which screw to use. Remake this. I'm dying
Anyone knows what to do if my VSett10+ shakes at high speeds?
JUST DO AS THE VIDEO SHOWS
Steering damper is a completely useless thing and investment! Just tighten the main screw in the middle of the handlebars and tune the rigidity of the handlebar rotation to your liking. Access to the screw is from below, so you don't have to disassemble anything!
I just received my scooter. I'll try what you say before buying a damper.
Do you have a video on how to do that?
@@rbmanb video not needed. Just tighten the Allen screw from the bottom of the handlebars.
@@jkmaxfli2469 if it fixes this issue you are a genius.
The wobbles at 40-50km/h are so scary.
@@rbmanb I have driven 1400km and I have never wobbled even at a speed of 70km/h on Vsett 10+ !
@@jkmaxfli2469 I'm also thinking maybe my wheel is inflated way too much.
Please let me know where I can buy this kit. Cheers.