It's been well over 35 years when I built something like this but I used a CD4069 hex inverter to monitor water level in a 50 gallon drum. I used pvc pipe with rivets at point to be tested for. Nice to see old school ways to solve a problem being shared. THANKS
This is impractical. This is not advisable to be employed in real water tanks. The "sensor wires" would eventually corrode because they are always soak in water and produce toxic elements in water due to electrolysis action.
Struth i run a clear hose outside my water tank and could see the level without all that work. Ran the clear hose from the tap attachment down the bottom. Simple cheap, no electicity
that's fine if you can get to the tank but this could also work for some kind of automation as well. when tank is empty fill it or when tank is full empty it.
How many times you need to climb the rooftop per day? What if the tank is on 3rd floor roof and you live on the ground floor. We don't have a permanent stair/ladder to the place where the tank is installed.
Hey, you can use 10k resistors on the base of transistors to protect the transistors in case probes are shorted, though not very necessary. You can use an opamp too instead of transistor to make the circuit compact. LM 324 is general purpose opamp. You can check datasheets for better options. You can also combine transistors and an opamp too in the kit.
I have done a successful modification in this syatem at my home. I have placed one of the sensor electrodes below the water inlet into the water tank. So, when the corresponding LED glows, it indicates that water is actually flowing into the matter tank.
I’ve got a concrete 3 meter high water tank. The way I do it is to tie a piece of string onto a float and put it in the tank, the other end of string (on the outside) tie a weight (slightly lighter than the float) as the water level goes up and down, so does the float, therefore telling you how much water is inside. Or get a stepladder and check it.
Of course I only need to look at that if the water input stop valve breaks or doesn’t work for some reason. Which has happened before, but I always knew how much water was in the tank
how long wire can be attached from tank to circut, 'cos often tank lie above the roof top and conection inside the building so it must be installed inside the buidling so its matter that how much long wire can be conected with it. please, however nice.
The list of the material you used is missing, perhaps with the link on Amazon. Furthermore, if I want to build on a 2000 liter vertical tank, what type of conductor rods should I use? Thanks for the great video.
@@RJEDITALL Thanks, can it be done for an underground tank with a height of 2 meters? Which materials should be used for drinking water, avoiding any contamination?
Great circuit !! I sow the diagram, but I was looking for Diode value, because I want to do it for my home, but I was not able to find the diode value, could you share it with me ? Appreciate your contribution and time to do this video !!
Diode number is not a critical thing here. You can use any diode that you have. Most common is IN4007. You can use OA79, 85 or 91 etc too that were used in radio. Don't use large pieces of diodes with several amps capacity, just a small one.
Hi dada ami apnar dakano sarkat tika baneache kintu amer akti poblam daka dicha .amer 20%Taka 30%,50%,80% jauer porau buzzer of hocha na .ami ki korta pari jodi aktu bola ditan tahola ami kubi upokrito hotam 🙏🙏🙏
Sab se bara masla ye ata hay k jo chez ham water tank may dalte hain wo bohat jaldi khrab ho jati hay chahe wires copper ki he kiewn na hon us ka koi hal batain bhai
power supply Voltage and Ampere , what's length of water tank and alarm circuit cable, what i do if tank at 21 floor and alarm circuit setup at ground floor , i thing its 210 ft to 250 ft its working DC or AC share Voltage and Ampere also
@@FranciscoMartinez-ik4nj Buenas tardes, ya le hemos preguntado yo, usted y varias personas, pero la respuesta es siempre la misma; En lugar de decir qué sería el diodo, le dice a la gente que revise la descripción de los artículos, que no dice qué sería. Al parecer lo hizo a propósito, falta de consideración, me gustó, pero lo borré y no me registré, otros deberían hacer lo mismo, quién sabe, tal vez ya no lo corte. Puedes comprar el IN4004 ok.
Es bueno, sólo conectar la batería cuando se quiera saber el nivel del agua en tinaco,....mientras no se necesite saber , desconectar de toda corriente y queda ok.
Good idea ❤❤
Thank u ❤️
It's been well over 35 years when I built something like this but I used a CD4069 hex inverter to monitor water level in a 50 gallon drum. I used pvc pipe with rivets at point to be tested for.
Nice to see old school ways to solve a problem being shared. THANKS
@@Quazee137 ❤️
Muito top esse projeto irmão 👊👍
Thanks for watching ❤️
This is impractical. This is not advisable to be employed in real water tanks. The "sensor wires" would eventually corrode because they are always soak in water and produce toxic elements in water due to electrolysis action.
If we solder with aluminum pieces
Work, you can use copper or aluminium bare wire
Você também pode usar uma ponta de grafite e isolar da água esta emenda com massa epoxi. 🇧🇷
I have tried so many ways. Its not working with overhead water tank. Good for water glass
@@SL-wp3ty check your transistor
a very nice video, keep inspiring, educate & share your skill with us, continue the good work with faith.
@@ElectroTechnics-g4s thanks for your valuable comment
Struth i run a clear hose outside my water tank and could see the level without all that work. Ran the clear hose from the tap attachment down the bottom. Simple cheap, no electicity
@@andymartinez767 👍
and what if you have underground tank?
that's fine if you can get to the tank but this could also work for some kind of automation as well. when tank is empty fill it or when tank is full empty it.
How many times you need to climb the rooftop per day? What if the tank is on 3rd floor roof and you live on the ground floor. We don't have a permanent stair/ladder to the place where the tank is installed.
Je suis impressionné par la minutie ,le calme ,la patience et la dextérité de ce Monsieur
Je n’ai rien de tout ça …😢
@@patricemurguet5247 thanks for visit
Muito bom esse projeto, a um tempo atrás eu também fiz esse mesmo projeto para o canal . Parabéns pelo seu projeto.
Thanks for visit ❤️
Good Design, Good Explanation, And good demostration
@@davidbana9851 thank you very much for your compliments
Sangat luar biasa dan bermanfaat .
Kami menyukai ini
@@kawol8997 thank you bro
Πολύ καλό, έψαχνα μια τέτοια κατασκευή είναι το καλητερο και πιο απλο ηλεκτρικό φλοτερ, σε ευχαριστουμε
U are most welcome ❤️
Muito bom. Faltou esquema e nome número dos componentes. 😅
Please check description
Thank you 👍🙏
@@BurRun-kt3tf you welcome
First actual decent tutorial amd excellent sodering ❤
@@octymocty132 ❤️🩹👍
How do you keep the copper wire tips from corrosion?
SUPER ❤👍👍
Thanks for watching ❤️
Perfect project. In this case for a big water tank we need electrodes in place of wires.
@@telosfd yes, you can use
Hey, you can use 10k resistors on the base of transistors to protect the transistors in case probes are shorted, though not very necessary.
You can use an opamp too instead of transistor to make the circuit compact. LM 324 is general purpose opamp. You can check datasheets for better options. You can also combine transistors and an opamp too in the kit.
Great.. basicly same level sound circuit....❤
👍
Cant wait to fit this in my Uranium enrichment plant in Iran, thank you
@@fidelcatsro6948 you are welcome
Posso usar este projeto em um tanque de gasolina
@@fazendodetudo-br yes
Aku subscribe karena aku ingin karya2 anda yg menakjubkan yg lain
@@samsulhadijuarizal7800 thank you for watching
Is this diode IN4007 or any other??
@@ad.9ine yes, 4007
I have done a successful modification in this syatem at my home.
I have placed one of the sensor electrodes below the water inlet into the water tank. So, when the corresponding LED glows, it indicates that water is actually flowing into the matter tank.
@@PKAgrawal-jm9uh good 👍
how can i can contact you? i want to ask questions
You can use your creative freedom to serve any purpose you want. A simple idea can change things drastically.
I’ve got a concrete 3 meter high water tank. The way I do it is to tie a piece of string onto a float and put it in the tank, the other end of string (on the outside) tie a weight (slightly lighter than the float) as the water level goes up and down, so does the float, therefore telling you how much water is inside. Or get a stepladder and check it.
Of course I only need to look at that if the water input stop valve breaks or doesn’t work for some reason. Which has happened before, but I always knew how much water was in the tank
You use this method with long wire
@@RJEDITALL Not wire, just a piece of string or nylon fishing line.
Is this work on a large 15 gallon tank. Which size of wires i will use for ..
@@exploringislam280 you can use any water tank, wire mm same
@RJEDITALL I have to only increase the length of wires
Thank you bro! I need this👍
Everything is so simple, and you can have as many levels as you like!
Thank you for watching ❤️
the electrical work is beautiful ❤Something by liking and sharing and subscribing can learn something ❤
@@Engineer-y3r thanks for watching ❤️
Sir regiteri kon si number wali hn
@@WaseemAbro77 bro please check all details in description, diagram link in description
Why not use a float system?
It will not show level
Diod konsa lagaya hey???
Check Diagram in description
very helpful. thank you for your knowledge... very useful... can be applied...
Thanks for watching ❤️
Nice video, thanks :)
@@RixtronixLAB you are most welcome
Diode kis value ka lagana hai
@@mmssmmss9508 4007
Super.
@@ValentinGavriliuc-z1y thank you ❤️
Home tank me use kar sakte he kya ????😊
@@Aforartist.13 ha , bro
how long wire can be attached from tank to circut, 'cos often tank lie above the roof top and conection inside the building so it must be installed inside the buidling so its matter that how much long wire can be conected with it. please, however nice.
@@MuhammadUsmanTaj you can use any longer wire
mere paas BC548 Transistor hai .kya a work karega ? plz riplay.🙏
@@ankanguria1174 no bro, you can use any NPN transistor
When used in very large tanks, will the resistance on the potentially longer green wires will be a problem?
@@cliffmathew you can use any size water tank
Is that applicable in a 1000 liters or above?
@@charlepakeo-an3409 yes
This highly risky don't do this
@@Arindam_Pramanik why
THAT GOOD AND OK LA 😮😮😮
@@khoaimo81 ❤️
Bună ziua!
Intre buzzer si ledul roșu inferior,ce valoare are rezistența?
Și cablurile de nivel sunt ceva cabluri speciale sau cabluri obișnuite?
@@sorinscreciu8258 you can use any cable, please check diagram in the description
ما هي المسافة التي تستجيب لها الدارة مثلا يبعد الخزان عن مكان وضع الدارة ٥٠ متر
You can connect any distance. Only, your cable needs to be longer
Kitna volt lagaga?
@@rabirana4883 5v
Interesante artículo 🤔😅
@@herculeskart7093 ❤️
Good Idea
@@abujobayed3966 thank u 👍
Why connect to speaker ?
You can connect direct to your water pump
@@AndrianSah-t4f not understand
The list of the material you used is missing, perhaps with the link on Amazon.
Furthermore, if I want to build on a 2000 liter vertical tank, what type of conductor rods should I use?
Thanks for the great video.
@@VincenzoScozzaro you can use any size wire, depends on your tank
@@RJEDITALL Thanks, can it be done for an underground tank with a height of 2 meters?
Which materials should be used for drinking water, avoiding any contamination?
@@VincenzoScozzaro you use copper wire without plastic copper wire
Pode ser usado em gasolina ?
@@Noobsoftcore 🤔
When water is pure ???
@@IjazAhmad-1 ❤️
Kya kya component h ye sb ke naam likhna
@@deleteconfusion7625 bro, please check description for all details in my website
Great circuit !!
I sow the diagram, but I was looking for Diode value, because I want to do it for my home, but I was not able to find the diode value, could you share it with me ?
Appreciate your contribution and time to do this video !!
@@carlosponce5514 diode 4007. Thank you
You can use any diod and also 4148 etc
Diode number is not a critical thing here. You can use any diode that you have. Most common is IN4007. You can use OA79, 85 or 91 etc too that were used in radio. Don't use large pieces of diodes with several amps capacity, just a small one.
Hi dada ami apnar dakano sarkat tika baneache kintu amer akti poblam daka dicha .amer 20%Taka 30%,50%,80% jauer porau buzzer of hocha na .ami ki korta pari jodi aktu bola ditan tahola ami kubi upokrito hotam 🙏🙏🙏
@@ayanguria2680 Bhai bhalo kare connection ta check Karo, thik hoye jabe
Excellent
@@charlessterzel6752 thank you
Why didn't you mention the value of the resistance you put in the first place?
@@TulipJack-t4j please check all details in description, diagram link in description
The description of an element that was used below the buzzer is missing, it will be a diode and how much
@@andyrio2829 yes diode, 4007
O circuito atendeu bem o esperado. 😊
@@franciscotadeudasilva870 ❤️❤️
❤❤🌷🌷
❤️❤️
Good Idea. This will avoid human intervention.
@@suhassulakhe8004 why
Need only two wires
The one at the bottom should switch on water pump and the one at the top should switch off the pump
👍
Usefull thx.❤
Thanks for watching ❤️
airnya nyetrum tak bang ?
@@bangamri_ you try, understand
may i miss where the supply is installed? without DC supply how this system can work?
@@zakiulhaq no working without dc input supply
thanks alot
@@abualharithalowaisy9831 you are welcome
Sab se bara masla ye ata hay k jo chez ham water tank may dalte hain wo bohat jaldi khrab ho jati hay chahe wires copper ki he kiewn na hon us ka koi hal batain bhai
@@imranrizvi8006 market me jo milta hai same hai, khrab nhi hoga
power supply Voltage and Ampere , what's length of water tank and alarm circuit cable, what i do if tank at 21 floor and alarm circuit setup at ground floor , i thing its 210 ft to 250 ft
its working DC or AC share Voltage and Ampere also
@@SpaceSoftSystem you can use any size water tank and wire, dc 5v 1-3A
Good afternoon. The description of the components was missing what the DIODE would be, could you please specify it to us?
@@junioricq please click diagram link in description
@@RJEDITALL I already clicked, but there is no diode reference, so I sent you a message
Buenas tardes. El número del diodo no aparece en la lista de materiales. Podría indicarme cuál es?
@@FranciscoMartinez-ik4nj Buenas tardes, ya le hemos preguntado yo, usted y varias personas, pero la respuesta es siempre la misma; En lugar de decir qué sería el diodo, le dice a la gente que revise la descripción de los artículos, que no dice qué sería. Al parecer lo hizo a propósito, falta de consideración, me gustó, pero lo borré y no me registré, otros deberían hacer lo mismo, quién sabe, tal vez ya no lo corte. Puedes comprar el IN4004 ok.
Great job.
Can plz show us the name? And the value of those components.
@@wasanthapriyashantha7035 please check diagram in the description, diagram link in description
is DC current contact to water dangerous to humans?
@@GrimReaper-rr8xh no dangerous problem, dc 5v
Can i use this for petrol tank? Please answer fast.
@@Artikaspeak I don't try, You can try, n make this
hello friend. good job.
How many meters can I place the circuit away from the water tank? if i use cat5 or cat6 cables?!!
@@3jcube3 you can use any wire, any length
Like
Thanks for visit 👍
Good
@@filmproduction1232 ❤️
ما قيمة أمبير الشاحن وهل يمكن استخدام شاحن ١٢ فولت مع تغيير قيمة المقاومة
5v mobile charger 1-2 ampere
What is that thing you connected at the buzzer. In order to use a 9v battery, which part do we need to change.
@@lrtaralte check diagram
Podria indicarme el numero del.diodo, ya que no aparece en la lista de mateeiales
@@FranciscoMartinez-ik4nj 4007
Hlo, Diode number pata nahi chal raha hai
@@jaysingh-ro8kd 4007
A float and string with weight at the other can give good indication . It will not give alarm. It becomes cumbersome if the height is like in a flat.
@@sasibhaskarakripa 🤔
Don't increase the complexity. This circuit does the job intended for the purpose.
Value of diode
@@johnacemangabat9752 4007
Hello, a description of the diode please, as the designation is not in the video, thanks
@@lm5106 4007
Very Good idea , but parts vslue????? Thank you
@@umeshkumarsah4679 please check description
How mamy voltage i can give to it for starting it can i use 9w battery
@@maggenix6324 3.7-5v dc, you can use mobile charger
For how many vots this circuit is working
@@abhijithmohan8962 5v dc
very good
@@usamaabdelaziz7387 ❤️👍
Bro welding machine banao
ok
brother using 12 V (dc ) or 5v dc
@@adapasateesh-od7wz 5v dc
What is the power supply value? Is it 12 volts or 9 volts?
@@st-iw8je 5v , you can use mobile charger 5v
it's diode IN4001 or IN4007?
@@qorispypuff 4007
@@RJEDITALLthankyou!!
Apakah ini Berlaku Untuk Solar?
You try
Well going by your thumbnail full is 125%? WTH??
@@JamesBruce32 ❤️
Hello bro, can I apply it to a large water tank, and will anything differ if I apply it?
Yes, you can use any tank
@@RJEDITALL I mean just make the wires longer is that all I need
@@maddsm66 yes
@@RJEDITALL Thank you so much
A 9V battery can be used for this thing please help ?????
@@ranganadeshan9565 yes, you add 47 Ohm resistor in input site
Can you tell me where the 47 ohm resistor is connected to please help???? @@RJEDITALL
@@ranganadeshan9565Connect 47 Ohm resistor the Input positive side , you connect 47 Ohm resistor before add your 9v battery
@@RJEDITALL Thank you ..
Value of resistance please
@@SanjoyPati-z9s all 1/4w
How can this be install in my old truck's gas tank?
@@loboxx337 same process, I don't work or not work
Plz mention value of resistances
@@mominsarker4764 please check diagram in description
Muito show
@@gersonepifanioterra1977 ❤️
Plz detail of component
@@amirmuhammad8689 check diagram in description
I would like to make the buzzer beep by connecting 555 timer in multivibrator mode, how should i add it to the circuit
@@sjoo2243 🤔
Es bueno, sólo conectar la batería cuando se quiera saber el nivel del agua en tinaco,....mientras no se necesite saber , desconectar de toda corriente y queda ok.
@@porfirioarroyo6023 👍
А динамик через диод запитан что бы если он уйдет в обрыв не было не света не звука?