Thank you for sharing your valuable knowledge. If you build your next project can you please do a video explaining the steps. If I only had mentors like you few years years ago I'd be far ahead by now
Does the display on each inverter show a total of power to the load or only for the specific inverter? Should the power figures be added for total power used, generated?
Thanks Dave, If you run two inverters in parallel, do the smart loads have the same operational mode or can they do different things on the different inverters. More specifically can they be set to go off at different battery SoC levels? Thanks
Great videos. You make a point that you can have many inverters on a single phase in a master slave configuration and the batteries must be on the same bus. Are you saying that all inverters in this master slave configuration can connect to one battery or should each inverter have its own battery (of the same capacity)?
Nice video, thanks for posting. Is there a forum for discussing some of the issues relating the the Sunsynk inverters? I am assisting a friend who has installed two 12kW three phase systems and we are battling with a F21 error and need advice
We have this system with Hydro feeding Master and Solar feeding Slave. However when we have drought or very low flow we are isolating the Powerspout PLT Turbines. However then the solar is barely working alone as Slave. What is the solution? We hope to add Wind too so ideally they need to be able to work independently. Phase rotation making them all Masters sounds good.
I have 2x 5kw inverters connected in parallel, working very well. I do notice the kWh recorded in mobile app is 50% lower than municipality smart meter. Any ideas?
Hello, If im running two 6K 1 ph One is connected to 2phases supplying it both with 220volts Other one is connected to 3rd phase also supplying with 220volts What are the master srttings for them? Should i sync them or just dont and they will do the job?
I see no point in that. I am installing my own here now and going with no. 1 to the left, then no. 2 middle and no.3 right hand side. Otherwize it is just a mess remembering.
In the manual - Hybrid Parity (Super) Inverter it currently says says for Sunsynk Wiring multi inverters "where more power is required it can be connected in parallel either single or 3 phase configuration. The maximum number of inverters that can be paralleled in a single phase utility grid is three (10.8kW, 16.5kW, and 26.4kW for the 3.6kW, 5.5kW, and 8.8 kW model, respectively) and the maximum number that can be paralleled in a three phase utility grid is nine (32.4kW, 49.5kW, and 79.2kW for the 3.6kW, 5.5kW, and 8.8 kW model, respectively)." In this video you mention that it is possible to parallel at least 10 inverters. Can you please clarify what the current limit is for the number of inverters than can be paralleled?
Have loved the videos... i am struggling to get some answers which i hope you can help with. I am busy installing a system at the moment. It has 2 x 8kwh, 12 410w PV Panel & 4 Pylotech Us3000. I am just looking for confirmation on the wiring. Setting up as a master and slave is easy enough but the wiring between the two inverters is where i require confirmation please. I am going to take all 12 panels into one inverter as 2 streams of 6. All 4 batteries will go into one inverter and then a parallel connection to the other inverter and the same for load and grid is this correct?
Thank you for sharing your valuable knowledge. If you build your next project can you please do a video explaining the steps. If I only had mentors like you few years years ago I'd be far ahead by now
Does the display on each inverter show a total of power to the load or only for the specific inverter? Should the power figures be added for total power used, generated?
I can see that each inverter has its won batter bank, is that correct? Or are they some how connected?
Thank you great video
Thanks Dave, If you run two inverters in parallel, do the smart loads have the same operational mode or can they do different things on the different inverters. More specifically can they be set to go off at different battery SoC levels? Thanks
Great videos. You make a point that you can have many inverters on a single phase in a master slave configuration and the batteries must be on the same bus. Are you saying that all inverters in this master slave configuration can connect to one battery or should each inverter have its own battery (of the same capacity)?
Nice video, thanks for posting. Is there a forum for discussing some of the issues relating the the Sunsynk inverters? I am assisting a friend who has installed two 12kW three phase systems and we are battling with a F21 error and need advice
Can you parallel different size inverters together?
We have this system with Hydro feeding Master and Solar feeding Slave. However when we have drought or very low flow we are isolating the Powerspout PLT Turbines. However then the solar is barely working alone as Slave. What is the solution? We hope to add Wind too so ideally they need to be able to work independently. Phase rotation making them all Masters sounds good.
Should the load / ups also be on a common bus?
I have 2x 5kw inverters connected in parallel, working very well.
I do notice the kWh recorded in mobile app is 50% lower than municipality smart meter. Any ideas?
Hello,
If im running two 6K 1 ph
One is connected to 2phases supplying it both with 220volts
Other one is connected to 3rd phase also supplying with 220volts
What are the master srttings for them? Should i sync them or just dont and they will do the job?
Thank you for making this video. What is the reason behind making the center the master? Cabling or something else?
I see no point in that. I am installing my own here now and going with no. 1 to the left, then no. 2 middle and no.3 right hand side. Otherwize it is just a mess remembering.
In the manual - Hybrid Parity (Super) Inverter it currently says says for Sunsynk Wiring multi inverters
"where more power is required it can be connected in parallel either single or 3 phase configuration. The maximum number of inverters that can be paralleled in a single phase utility grid is three (10.8kW, 16.5kW, and 26.4kW for the 3.6kW, 5.5kW, and 8.8 kW model, respectively) and the maximum number that can be paralleled in a three phase utility grid is nine (32.4kW, 49.5kW, and 79.2kW for the 3.6kW, 5.5kW, and 8.8 kW model, respectively)."
In this video you mention that it is possible to parallel at least 10 inverters. Can you please clarify what the current limit is for the number of inverters than can be paralleled?
AC couple system. How much battery capacity can be installed for each inverter?
Hello, do you use Islande mode ? Thanks
Is it possible connect in parallel Hybrid inverter with On grid inverter , using Hybrid inverter as grid supply
Have loved the videos... i am struggling to get some answers which i hope you can help with. I am busy installing a system at the moment. It has 2 x 8kwh, 12 410w PV Panel & 4 Pylotech Us3000. I am just looking for confirmation on the wiring. Setting up as a master and slave is easy enough but the wiring between the two inverters is where i require confirmation please. I am going to take all 12 panels into one inverter as 2 streams of 6. All 4 batteries will go into one inverter and then a parallel connection to the other inverter and the same for load and grid is this correct?
Damian Nelson you can call our SA help line
@@sunsynk That would be great can you give me the number?
Damian Nelson +27 (082) 504-4510 Shabir
DYNESS battery . Thanks for your video.
Why are the batteries isolated between inverters?
Otherwise you would have mains on the battery terminals, one bus shares batteries for all inverters.
where are the manuals ?
Thanks for video
🌻