ฝัง
- เผยแพร่เมื่อ 20 ส.ค. 2024
- Donate me on Patreon. Anything will be appreciated!!
/ ezmeck In the last part of gixxer 150 rebuid there are some key facts that has been discussed in this video, valve lapping, valve seal check, how to fit valves with no special tools, how to match ignition timing, where to use rtv sealant and where not to and a lot more. watch till the end.
Valve job guide video
• Valve Grinding, Lappin...
PEASE SUBSCRIBE TO MY CHANNEL AND PRESS THE BELL ICON TO STAY NOTIFIED.
IF YOU ENJOYED WATCHING THE VIDEO THEN LIKE COMMENT AND SHARE THIS VIDEO. THANK YOU!
FOLLOW ME ON FACEBOOK
/ rajib.sarkar.39
FOLLOW ME ON INSTAGRAM
/ ezmeck.yt
Sir gadi pickup nhi le raha h even after full throttle dene k baad bhi..clutch plates bhi change kr chuka hu fir bhi same issue h.. Abhi bhi
Tnxxxxxx brooooio
Bhai company to bola exhaust 0.10 se 0.16 rakho. To ap ku lagia 0.8
I'm having a Gixxer 155 2019 naked model, I want to add the fairing of the SF model can you tell me whether this can be done without any Welding work or not? Also can u make a fairing re-assembly video? 🙏
No welding is must.
@@EzMeck where do I need the welding to be done please can you guide me
@@vader9985 you have to get another sf with fairing removed, only then the exact measurements can be found. I cannot explain that here, some svc do that, as they have the provisions to get the exact measurements.
@@EzMeck ok I'll go and ask around in the service center
Intek .05Mm
Exhusht. 08mm
is it possiple to convert my gixxer 150 fi 2018 into 4valve set up?
May be, but I am not aware of that.
Hi bro,
Can you mention which mm gap is good for inlet and outlet tapped
in service center they have configured for 0.04mm and 0.16mm
but i feel power loss on top speed
Can you suggest the mm for tapped please.
0.04 mm is very less, its better to have a loose valve than a overly tight valve, the engine may stall in low rpm, or in sudden deceleration. Set the intake @0.08mm and exhaust for 0.16mm. the permissible range for intake is .04-.08mm and that for exhaust is .12-.16. so if they set .04 then the exhaust must be set at .12 and vice versa. Otherwise the volumetric efficiency will not be good and the performance will be compromised.
@@EzMeck thanks bro that helps 😊
@@EzMeck
Hi bro,
In this video you kept 0.05mm for inlet and 0.08mm for outlet is that good valve clearance for good mileage and performance?
Or you suggest any other valve clearance for inlet and outlet?
Because these service centers are not doing properly
So am going to do it with private expert mechanic
so please suggest your setting for inlet and outlet in this video is enough for good performance?
@@gkcheetah7542 set intake @.08 exhaust @.16, because its always better to have a loose valve than a tighter valve. If you hear noise the reduce that by .02mm.
@@EzMeck OK bro thank you
👍👍👍👍👍👍
Sir what are the clearance of intake and exhaust.thanks
Gixxer 155 intake 0.06mm exhaust 0.12mm
Oil is burning on my gixxer. But there is no smoke. Is it valve seal complaint, or pistion and cylinder comllaint ?
It might be in the initial stage of bad rings, it is smoking in high rpm for sure. If it smokes in idle rpm its valve seals.
@@EzMeck ok
@@EzMeck how can we overcome it
Sir honda trigger par video bnayo
Zarur try karunga.
@@EzMeck sir please 🙏 video banao
vai mera gixxer sf head mai oil leakage aaraha hai ...solution keya karu or engine light malfunction on ho geya hai keya usika baje se ei ho raha hai..pls help me.. and i m from purulia wb no one special mechanic in our local for suzuki
Replace the head gasket
@@EzMeck ThnQ bro
@@EzMecksir best sealent paste for this problem
Where r u from bro from India, I want to repair my bike 🔥
I am from west bengal.
Good day sir. May I ask if it can be fixed if the rocker arm housing has some scratches caused by friction?
Yes by adding some washers it can be fixed.
Oil level is going down after some kms. Is it burning of oil?
It may be blow by also, either way piston rings are shot.
@@EzMeck how to identify it that is it from piston rings
Best way to check is to do a compression test. Otherwise u have to take everything apart then examine.
@@EzMeck how can we do a compression test ?
Can you sell me this cylinder head compleat with WITH CAMSHAFT & ALL PARTS INCLUDING VALVE COVER, used parts are ok as long as i can rebuild? Im in the USA.
Dm me on instagram
@@EzMeck i dm you on IG about this head and buying one and sending to California?
@@EzMeck are you going to answer me on IG and sell me a gixxer head?
Sir seat ka lapping kitne baar kar sakte he maximum?? Koi limit he kya sir? Mera 3 baar lapping ho chuka he gixxer ka head valve seat.please reply
Lapping means sanding, so agar somehow Aisa koi scratch ajata hai jise hum lapping paste se grind karke Nehi hata sakte tav seat Ko cut karni Hoti hai. Har ek engine head ki valve seat ki ek angle Hoti hai, us angle me lathe machine me cut karne se valve seat firse reuse Kar sakte hai.
@@EzMeck okay sir
Why my gixxer doesn't start in single self after parking it? I have to take 4 self to start it after leaving it for 15,20 mins.
No problem with cold start up.
Is it a carbureted one or a fuel injected one?
In cold condition it starts right away in single self. Also in very hot condition right after stopping the bike , it starts right away. Only problem when I start it after 15 mins. Why is this strange problem in my gixxer??? Any idea?