hello. I have a question about the pz26 carburetor. By turning the screw for adjusting the mixture, i.e. turning it to the right, we set the mixture to be poorer in fuel?
Hey man, mabe you can help me. When riding in leveled straits, above 7000rpm with stable speed, i get this strange hicups... but in all other conditions, like accelerating, climbing, it works perfectly. Even works fine in the same range of RPM with the motorcycle pulling, like in climbs. I already cleaned the carb, checked the vacum system for leaks, replaced vacuum pump and nothing solves the problem... I have a sym xs125 with a pz27 carb, very basic. Anything i should try? Or anything i should have made different during cleaning?
I ordered a carburettor from eBay and they didn't send the item with the little c clip that holds the needle, so now I have 2 brand new carby but unfortunately no way to control the throttle
thanks man, more info about my carb which i can clean now and hopen i get it sorted as it runs fine but random times it dies and even when going in neutral, it just dies on me when riding.
Does the choke have to be completely open when it starts and then close when it is warm, so that it is half open? I've adjusted a lot and it only works when it's all open. when I turn it to the middle, it goes off again
Sorry I've only just seen this , if it's a cold start it's easiest to have the choke fully closed so there's no air flow but once started some bikes need it on middle for the engine to warm up then after that it should fully open so all the air can flow through if your putting it on middle and it is cutting out then its not getting enough air so will need to be fully open I hope that helped although its been 3 weeks
@@nottosuretbh7417 found it :) If someone search, it should be 14mm from the carbburetor body (from gasket surface) to the top top of the float when closed. Should be measured at the front part of the float (closest to engine side).
Decent video but why the hell put music over the top.
If you prefer it without the music I can do that for future videos just thought the video would be abit boring without some sort of background
Id much rather a narrative than music.
hello. I have a question about the pz26 carburetor. By turning the screw for adjusting the mixture, i.e. turning it to the right, we set the mixture to be poorer in fuel?
Hey man, mabe you can help me.
When riding in leveled straits, above 7000rpm with stable speed, i get this strange hicups... but in all other conditions, like accelerating, climbing, it works perfectly. Even works fine in the same range of RPM with the motorcycle pulling, like in climbs.
I already cleaned the carb, checked the vacum system for leaks, replaced vacuum pump and nothing solves the problem...
I have a sym xs125 with a pz27 carb, very basic.
Anything i should try? Or anything i should have made different during cleaning?
how to fk up an instructional video = add music
I ordered a carburettor from eBay and they didn't send the item with the little c clip that holds the needle, so now I have 2 brand new carby but unfortunately no way to control the throttle
Great video, plenty of good information. These are the carbs on alot of Chinese bikes aren't they?
Yessssss
thanks man, more info about my carb which i can clean now and hopen i get it sorted as it runs fine but random times it dies and even when going in neutral, it just dies on me when riding.
I really hope this helps man good luck with the bike 🤞
@@nottosuretbh7417 yep one problem sorted, it wont shut by its self anymore :D idle was too low
Does the choke have to be completely open when it starts and then close when it is warm, so that it is half open? I've adjusted a lot and it only works when it's all open. when I turn it to the middle, it goes off again
Sorry I've only just seen this , if it's a cold start it's easiest to have the choke fully closed so there's no air flow but once started some bikes need it on middle for the engine to warm up then after that it should fully open so all the air can flow through if your putting it on middle and it is cutting out then its not getting enough air so will need to be fully open I hope that helped although its been 3 weeks
@@nottosuretbh7417 now my bike is by the cops😅 chase with cops
I cant find the jets that go for this carb
did you ever find them having the same problem here
The music ruined it
PZ26 Can upgrade to PZ27?
Pretty sure you can but I normally upgrade to a pz32
I have a 110 will it work?
As long as the carb is the same design I shouldn't think why not hope goes well
What should be float level/height on this carb?
Sorry man I honestly don’t know been a very long time since I worked on one of these carbs I hope you find the answer somewhere
@@nottosuretbh7417 found it :) If someone search, it should be 14mm from the carbburetor body (from gasket surface) to the top top of the float when closed. Should be measured at the front part of the float (closest to engine side).
Annoying frigging music..aaahhh!
I've had a few comments about that ill keep it in mind for future thank you
buy it new for 26,00 EUR