Rampworx Buyers Guide: SCS Scooter Compression Tutorial

แชร์
ฝัง
  • เผยแพร่เมื่อ 16 ธ.ค. 2024

ความคิดเห็น • 31

  • @binlorry
    @binlorry 9 ปีที่แล้ว +3

    thanks! I've watched so many videos on this and none have helped! after I watched this one I understand!

  • @alexkierontylernathanmitch5111
    @alexkierontylernathanmitch5111 9 ปีที่แล้ว +1

    Very helpful, thank you!

  • @tomfinglass4078
    @tomfinglass4078 9 ปีที่แล้ว +1

    I've got a problem with my scs I'm using drone majesty v2 forks a grit scs and district hic bars i have taken the slit off and the back of my clamp is not parallel at the back where the bolts are this is causing creaking its not a problem with my headset idk whether to buy new bars or a scs help please!

  • @bowie5668
    @bowie5668 7 ปีที่แล้ว +1

    Would I need a headset spacer with an envy kos v3 deck and a root air fork?

  • @foottheadd
    @foottheadd 6 ปีที่แล้ว +1

    when i buy forks it says hic or scs works but scs forks are skinnier so im confused if they will work for scs

  • @michealchecavich3708
    @michealchecavich3708 9 ปีที่แล้ว +3

    2 questions.
    1. do you need the topcap? and will it change the the speed of which it spins?
    2. how do i make mine spin faster?

    • @rapidbluur5149
      @rapidbluur5149 9 ปีที่แล้ว

      micheal checavich Hi to answer your questions, yes you will need a top cap as it helps protect your headset bearings for from dust etc which will also increase the life of your bearings.
      To make your headset spin faster you could try tighting it as tight as possible and then loosing the bolt a little bit to make sure your compression spins good but also is solid, you could also try re-greasing the bearings if they are fairly old as the grease will eventually go away or if the headset bearings are new they should be able to spin smoothly and fast with the compression fairly tight.

    • @michealchecavich3708
      @michealchecavich3708 9 ปีที่แล้ว

      thanks so much

  • @funnytroublemakers9627
    @funnytroublemakers9627 8 ปีที่แล้ว +1

    I don't have a slip in my bars can I just get a new. Clamp cause I tighten them and they come off help please 👍

  • @harrisonevans131
    @harrisonevans131 7 ปีที่แล้ว +2

    Do tilt arc scs clamps work well with drone majesty v2 forks

  • @sampoh9483
    @sampoh9483 7 ปีที่แล้ว +1

    so do i need headset spacer if i am going to use UrbanArtt Evo LeBaron fork and urbanartt trail deck and District HT-Series SCS??

    • @ravishiki
      @ravishiki 7 ปีที่แล้ว

      Sampo Hurskainen i should buy one in case you need it

  • @agingergamer183
    @agingergamer183 9 ปีที่แล้ว +2

    you guys forgot to do tutorial on hic compression

  • @adama9601
    @adama9601 4 ปีที่แล้ว

    If I put a headset spacer on my scooter would it make my bar taller and what would happen if I put allot of spacers on it, would my compression be really loose or would it be fine

    • @reidmichels5575
      @reidmichels5575 4 ปีที่แล้ว

      The point of the spacer it to allow the scs clamp to fit with a longer fork. You usually won't need a lot of spacers for it to work.

    • @reidmichels5575
      @reidmichels5575 4 ปีที่แล้ว

      And no, it doesn't make your bars taller

  • @jeremiahs4862
    @jeremiahs4862 8 ปีที่แล้ว

    Can you use SCS forks with a regular double clamp from tilt (non SCS)?

  • @vaggexmp1995
    @vaggexmp1995 9 ปีที่แล้ว +1

    i dont ave a 10mm specer can i use two of 5

    • @ree83ce
      @ree83ce 9 ปีที่แล้ว

      I suppose so. I'm no expert but try it and if your scooter explodes, you may have a problem...

    • @vaggexmp1995
      @vaggexmp1995 9 ปีที่แล้ว

      hhahaha ok i'll try it

  • @noah-fd8ei
    @noah-fd8ei 7 ปีที่แล้ว

    My scs bolt I would tighten it and it wouldn't tighten anymore and its not fully in the forks

    • @kingacew2755
      @kingacew2755 7 ปีที่แล้ว

      TH-cam Manager u need some headset spacers

  • @jacefordyce3148
    @jacefordyce3148 3 ปีที่แล้ว

    How can the slit be removed

    • @ryanjames6610
      @ryanjames6610 2 ปีที่แล้ว

      Either with a bar adapter or cutting the bar down

  • @limitless9909
    @limitless9909 8 ปีที่แล้ว

    so if it has a slit i cant use my bars with scs

    • @axfnu
      @axfnu 8 ปีที่แล้ว

      +Mr.Ayy Lmao no, but it may work with hic, you can, however change your bars into scs by going to your local scooter shop and ask them top cut the slit.

    • @limitless9909
      @limitless9909 8 ปีที่แล้ว

      +BlueEnderGaming :3 thx

  • @debbiewatson6139
    @debbiewatson6139 9 ปีที่แล้ว +1

    Hi