One flaw I found on this V8 drill is that while drilling with the shaft facing down/upwards, the oil in the engine would go in a way that some bits of the engine would not get any oil. I would suggest installing a dry sump system so that every part of the engine will get the oil regardless of what angle the engine is facing.
Very good point. I'm also curious how the drive shaft of the engine takes thrust loads rather than axial loads. Most car crankshafts are not made to take a load in that direction. I would fit thrust bearings. Overall I'm thinking that a V8 powered flex shaft machine would make more sense. Then again if it's about making sense...
I was thinking the same thing too. Lmao 🤣. Great comment. You got to it before I did. & Three days before I saw this video. Regardless great comment! 😂
I always thought that I was a good vehicle mechanic,having worked on Cars, Motorcycles, HGVs,Heavy plant,Tanks. But your skills are next level. Unbelievable skill.
I’m a mechanic and every engine I ever saw has the oil pick up on the front end where the harmonic balancer is. Front end of the oil pan. So that’s not technically true. If you lean the drill forward there’s possibly enough oil to still be getting pumped since the oil pick up is probably up front.
I spoted a few problems. 1st is you are applying thrust pressure on the crank that it wasn't designed for, that engine will not live long. 2nd, the coolant taps are on the wrong end of reservoir. When you drill downward, the taps get no coolant. Fill the tank up more, or move taps. 3rd, good for high-speed stuff but with no reduction, power is going to be lacking in a big way
@@Guns_N_Gears I mean, it would have been a lot funnier if you said it which is why i gave you the opportunity to claim it but I guess I'll take credit for the joke 🤣
It's just for display and drills some holes so it works for its purpose with no problem. It needed a centrifugal clutch with a thrust bearing and a planetary gearbox on the front to make the output run to around 1000-3000rpm with WOT.
chuck mounted directly on crank? them bearings or bushings lasted max 5min of drilling. working any longer then that, if any, it'öö soon have grenaded itself from over heating since it couldnt get any coolent whilst drilling down-right.
Great vid. I would have shown how you changed the location of cooling tank feed port from the back to around the front side so that the engine still gets coolant when the drill is vertical. I was gonna comment that you should make that exact change, when in the last minute of the video I noticed that suddenly it had changed. Always good to show problem solving FWIW.
That’s absolutely the worst thing you could do to an engine is to put it sideways or upside down. It’s supposed to remain flats when you put it upside down or different directions the oil will get into places it’s not supposed to go and it’s actually gonna damage the motor..
No more silent drilling at night, without anyone noticing! Never liked that secrecy anyways. ❤ They said, now iis the tme to switch your gasoline powered car to a fully electric vehicle, powered by rechargeable batteries. With thatt spare V8 motor collecting dust in your garage for too long, you now have finally restored balance in your part of the universe. You really did an awesome DIY job, by a real V8 gasification of your old rechargeable drill! I would lole to build one of these gadgets myself, If i only had one of those sweet small gasoline motors available to me... (Someone out there wanting to hook me up with one of those?)
These miniature engines cost thousands of dollars for some reason. Maybe you can fashion one out of a chainsaw motor instead, comes with a centrifugal clutch already, you'd theoretically only need 90 degree gears on the output, or just drill with the motor sideways!
It's nice that you used the engine for a practical application - nearly all of the other videos on these micro engines just assemble them and run them, but don't put them to work.
There is a creator on also TH-cam who works with these engines. He mills out new pullies and replaces plastic parts with metal. The flow of the pumps and cycling of the coolant are much better when he's done with it. I'm sure if you took what he does you'd get better speed and torque.
Always thought about how cool it would be to make such but with a .21 nitro RC car engine..... But this............ I really wanna see him test it, I'm sure its got endless potential! You know youre buddy's a gearhead but when he pulls out his V8 drill to work on his V8 car........ There's a poetry in that.
But again, I know you’re just doing this for video purposes and I’m not expecting this to be something perfect like a factory would do or an engineer would do. It’s nice to watch good work.
So, how hard is this on your hand? I cant imagine its very pleasant to hold for more than 10 seconds. Especially with the power of yhe torque, in the palm of your hand, but also with the vibrations.
Can't drill vertically for too long or engine will overheat, the pump started pumping air because all the liquid was on the other side of the tank. Still, very cool for a DIY project, it looks badass!
So funny how people can find something wrong with a one-of-a-kind thing. Like how they know it's supposed to last more than five minutes lmfao. This is by far the most American outside of the box shelf, shop talk kind of thing any mechanic or fab tech or shit I mean anyone really that does any type of work with their hands this is like a memorabilia type thing I would imagine but actually works to show off with once in a while obviously he you got other drills lol. Way impressive and hats off to ya most impressive indeed for sure. Keep on keeping on yo!!!!
Awesome little project! It does amuse me, however, that so many people think its more powerful than a battery drill. This is a great analogy for an electric car. Need a battery to turn a motor to start the inefficient engine that is loud, cumbersome, & more finicky to build & maintain.
It's LITERALLY, Tim Allan from "Home Improvement"! Seriously if you were in the show Tim would do his lil "HarHarHarHar" grunt when he's talking about giving a tool MORE power Haha. I absolutely Loooooove this!! Man i really wish my brain worked liks this. I mean dont get me wrong i am not incompitant. But I am not nearly as skilled with things of this nature still second guess some of my work. I am just now starting to learn how to use a tape measure properly. I was horrible with math growing up.
No drill will ever be as cool as this one.
Jokes aside, someone already made the same thing on youtube.
@@shirufin5928 Gas powered drills are pretty common. I've been using them for like twenty years.
Have fun putting it in reverse 😂
lol imagine going to work and seeing some guy with this
@@MayorMcheese12lol
Portable, light, low noise and vibration....ideal for getting into hard to reach places.
How the hell where you able to use that monkey emoji thing here on TH-cam? 🤔
the torque on that might be insane
this comment.....
mkay I guess im not the only dirty minded person here
@@SYN7H3T1C4bro 💀😭😭🐱
What obligation did you feel to word your comment like that
Everyone be showing off with their DeWalt drills, till they hear you revving Ur drill on the next floor. So sickkkk 😂
😂😂😂
wait gimme a sec i gotta fill mine up with gas
I have to fill up petrol and warm up the engine
Gotta fill up with unleaded! And warm up yeah. And create a chain.
Bro: can i use ur drill
Me: sorry it ran out of gas 😂
กกฟกก
😮 13:25
해야할일이 너무 없어보입니다..
Well I think it would be faster to refuel it rather than having to wait for a traditional electric drill to charge
O miserável e um gênio
the most american drill
🦅🇺🇲🦅🇺🇲🦅🇺🇲🦅HELL YEAH BROTHER 🦅🇺🇲🦅🇺🇲🦅🇺🇲🦅
It would have a gun fitted in it😂.
american? than it should be cheap and not working...
@@derbayer8710Your country is 💩
@@anchitpatil7542Damn straight
This has got to be one of the, if not the most, coolest power tools out there! Extremely well done sir!
Только получается не электро )
@@stp2381exactly😂👍🏼
Spacemarine chainsaw 🌚
Okay, watching you just magically materialize a drill just to fix your drill is very funny
Exactly what I was thinking! lol. The irony.
As a mechanic i need to have this. This would be a topgear special powerdrill.
I'll wait for the V12 to order 😂🤘
I'll wait until Full Self Drilling Mode and Ludacris Speed Drilling become Standard equipment.
@@trekinseattledrill plaid+
Rotary engine, like WW1 Aircraft
😂😂😂😂😂
The radial 16 with 700 horses
One flaw I found on this V8 drill is that while drilling with the shaft facing down/upwards, the oil in the engine would go in a way that some bits of the engine would not get any oil. I would suggest installing a dry sump system so that every part of the engine will get the oil regardless of what angle the engine is facing.
Very good point. I'm also curious how the drive shaft of the engine takes thrust loads rather than axial loads. Most car crankshafts are not made to take a load in that direction. I would fit thrust bearings.
Overall I'm thinking that a V8 powered flex shaft machine would make more sense.
Then again if it's about making sense...
2 stroke, no oil
I noticed he certainly didn't rev too hard probably to accommodate this issue.
Yes 2 stroke solves the oil issue as lube is in the fuel itself
@@backwoodsboyslogging261 It's a 4 stroke, according to the manufacturer's website.
@@orderofmagnitude-TPATP Nuh uh it's a 4 stroke according to the manufacturer's website.
Please please please let the Torque Test Channel review this so we can see what type of power it's putting down!!!!
Without a clutch i don't think it's safe to stress test.
It fake 😂😂 lol
@@rinasmart9130 It's not, that engine is real and other youtubers have built a similar drill.
@@jovand6606 Thanks
dont think it's more than electric
Tim "The Toolman" Taylor approves this. More Power!
Glad I'm not the only one who thought that!
Grunts three times
Very cool!
If I had one I'd want mini coolant temp and oil pressure gauges!
While your there why not add a supercharger and a turbo 🤔🤯
@@J.R.jr-pc7bo That would probably rob the useful idle power. Maybe for concrete lol :)
Mình ở việt nam . Mấy anh em cho mình hỏi cái động cơ đó bao nhiêu tiền vậy . Ở việt nam không có bán
I may be wrong but no oil in these Toyan V8 motors, like an RC model motor.
@@nhutle9127 Why no small engines in Vietnam? Vietnamese like hobbies too.
You rebel! Society is trying to go all electric, and you convert an electric drill to ICE! I like your style!
I feel like this is something you would see on the old show home improvement, the binford 3000 v8 drill
I was thinking the same thing too. Lmao 🤣. Great comment. You got to it before I did. & Three days before I saw this video. Regardless great comment! 😂
This is by and far the coolest drill I've ever seen!!!
Хочу дизельный перфоратор, делать ремонт в квартире, в 4 утра!😂
представь рожу соседа, который в 4 утра пытается тебе свет выключить на площадке а не сработало😁😁😁
@@сашоксашок-х2з🤣🤣🤣
Ахахахахахаахахха,ебать я ору
Будет ещё веселее когда твой дизельный перфоратор в разнос уйдёт. Суета на весь подъезд обеспечена😂😂😂😂😂😂😂
For those wondering. This is a Toyan Nitro 4 Stroke V8 RC car engine. IT IS NOT 2 STROKE. Uses preapplied grease when it assembled for lubrication
That's awesome that's like every V8 Gearheads ultimate drill right there
I always thought that I was a good vehicle mechanic,having worked on Cars, Motorcycles, HGVs,Heavy plant,Tanks. But your skills are next level. Unbelievable skill.
Excellent fabricator skills thinking WAY outa the box!
Box? Which Box?
Do those engines have thrust bearings. If not it might develop some problems when the crank is being pushed on while drilling.
also in the cylinder bore
Might also experience oil starvation when drilling directly downwards
@@markellii3093a two-stroke engine would be the remedy for that one 😂
I’m a mechanic and every engine I ever saw has the oil pick up on the front end where the harmonic balancer is. Front end of the oil pan. So that’s not technically true. If you lean the drill forward there’s possibly enough oil to still be getting pumped since the oil pick up is probably up front.
@@barbarianmylaststand3918 what about drilling the ceiling then?
Badass! But how are you going to have it turn direction? 🤔
Only drill no coming back
Needs a transmision😎
flip the camera upside down🤪
@@airgunningyup 🤦 why didn't I think of that 🙃😅
easy, another V8 drill that runs backwards
This is actually one video on you tube that I would have loved to hear the commentary explaining how it was done.
I spoted a few problems.
1st is you are applying thrust pressure on the crank that it wasn't designed for, that engine will not live long.
2nd, the coolant taps are on the wrong end of reservoir. When you drill downward, the taps get no coolant. Fill the tank up more, or move taps.
3rd, good for high-speed stuff but with no reduction, power is going to be lacking in a big way
So what you're saying is he should add a gearbox with a clutch and shifter? Hold on I need to shift my drill into 3rd gear
@@StephenSmith304 Did I say that? You did!
@@Guns_N_Gears I mean, it would have been a lot funnier if you said it which is why i gave you the opportunity to claim it but I guess I'll take credit for the joke 🤣
@@StephenSmith304 It was 😁 funny lol, but either way, seems a lot for a $3 dollar drill that won't last long!
It's just for display and drills some holes so it works for its purpose with no problem.
It needed a centrifugal clutch with a thrust bearing and a planetary gearbox on the front to make the output run to around 1000-3000rpm with WOT.
IF you make this with a 2 stroke engine you can make it run reverse too
it is 2 stroke and it doesnt matter if its 2 or 4 stroke what matters is the gearbox i needs to have a reverse
@2StrokeWRLD but a 2 stroke engine IF you turn it backwards when starting it will run backward without a gearbox
"Can I borrow your drill?"
"Sorry, it's in the shop getting an oil change and new plugs"
🤣
lol
Hilarious.
Interesting overkill.
Going to get massive muscles operating that thing.
Great results.
chuck mounted directly on crank? them bearings or bushings lasted max 5min of drilling. working any longer then that, if any, it'öö soon have grenaded itself from over heating since it couldnt get any coolent whilst drilling down-right.
Shut up armchair engineer let’s see you build something cool
Stop. This is just for the fun of it!
Jaw dropped. Most awesome thing I've seen today 😮
Impressionante ideia, inclusive se a broca travar não queimará o motor! haha
This is the least practical thing I've ever seen, yet the coolest fucking badass piece of equipment I've ever seen
One of the coolest projects I've ever seen lol
ive always thought offhow cool a drill hooked up to a engine would be but i never knew how someone would do it this vid is amazing
ผมเคยคิดที่จะทำแบบนี้ แต่มาเจอวีดีโอคุณทำก่อน โอเคเลย ได้ไอเดียร์การทำแล้ว ผมไม่ต้องคิดมันแล้ว ดูคุณแล้วทำตามก็พอ 😂😂😂
Hi, with the 4 stroke from fridge compressor, could you make the rotor a permanent magnet style and put winding back over for a generator?
That is insane, great job. Thanks for sharing.
You have just combined to of my most favorite things power tools and engines and made the most majestic thing I’ve ever seen well done sir well done
Man I love this
Отлично Сэр! Но теперь мы желаем дизель!)))
This feels American 😂
Drill EV ❌
Drill V8 engine normally aspirated ✅
Can I please be on your zombie team?
Wicked. Creativity replying to the people who says the co2 is killing the planet. Love your videos bro. The world needs your skills to evolve.
Great vid. I would have shown how you changed the location of cooling tank feed port from the back to around the front side so that the engine still gets coolant when the drill is vertical. I was gonna comment that you should make that exact change, when in the last minute of the video I noticed that suddenly it had changed. Always good to show problem solving FWIW.
"Hey, I need to refuel my drill"
"You what?"
I was scrolling through TH-cam trying to find something to watch and I saw this thumbnail and first thought was finally someone gets new subscriber
Gets it**
That’s absolutely the worst thing you could do to an engine is to put it sideways or upside down. It’s supposed to remain flats when you put it upside down or different directions the oil will get into places it’s not supposed to go and it’s actually gonna damage the motor..
No more silent drilling at night, without anyone noticing! Never liked that secrecy anyways.
❤
They said, now iis the tme to switch your gasoline powered car to a fully electric vehicle, powered by rechargeable batteries. With thatt spare V8 motor collecting dust in your garage for too long, you now have finally restored balance in your part of the universe.
You really did an awesome DIY job, by a real V8 gasification of your old rechargeable drill!
I would lole to build one of these gadgets myself, If i only had one of those sweet small gasoline motors available to me...
(Someone out there wanting to hook me up with one of those?)
These miniature engines cost thousands of dollars for some reason. Maybe you can fashion one out of a chainsaw motor instead, comes with a centrifugal clutch already, you'd theoretically only need 90 degree gears on the output, or just drill with the motor sideways!
I'm a simple man. When I see V8 powered hand tools I hit the like button.
It's nice that you used the engine for a practical application - nearly all of the other videos on these micro engines just assemble them and run them, but don't put them to work.
This is an extremely great innovation, it can create a new trend, I hope many people know about it❤❤
There is a creator on also TH-cam who works with these engines. He mills out new pullies and replaces plastic parts with metal. The flow of the pumps and cycling of the coolant are much better when he's done with it. I'm sure if you took what he does you'd get better speed and torque.
Who are they? I'm digging this stuff!
Using a drill to disassemble a drill is like the coolest thing I've seen today wtf
It’s exquisite,a fine piece of engineering and practicality.
Always thought about how cool it would be to make such but with a .21 nitro RC car engine..... But this............ I really wanna see him test it, I'm sure its got endless potential!
You know youre buddy's a gearhead but when he pulls out his V8 drill to work on his V8 car........ There's a poetry in that.
Co worker: yo can I use your drill?
This guy: sorry bro it needs an oil change.
But again, I know you’re just doing this for video purposes and I’m not expecting this to be something perfect like a factory would do or an engineer would do. It’s nice to watch good work.
와... 진짜 박력 넘치고 강력함이 느껴집니다. 대단한 아이디어네요 와우..
This is one of the best youve convert.. a real engine power drill
This is one of the most "Tim the tool man Taylor" things ive seen in a while.
Dad:hey son pass me that v8 5 inch drill
🤣🤣🤣
Cool, please make other house hold items with engines, e.g. TV, refrigerator, toaster, tooth brush, etc!! That will be very entertaining
Its so ridiculous and I love it. When a friend comes over you need to pull that out and say, "heres a real drill" lmao. Very cool bud
suggestion: use a "momentary" switch for your starter, that way it stops when you stop pressing it (like a regular starter)
Bro: can i use ur drill ?
Me: sorry, it went to F1 racing.
well... V8 are banned now, so...
Now that is proper cool! Some proper engineering skills to make that badass drill.
This is the kind of ridiculous that keeps me up at night, and renews my faith in my species abilities. You sir are a freak. Thankyou, God bless. :)
O M G!!!! COOLEST drill EVER i wanta have a beer with this guy!
This is a super cool concept, but wouldn’t weight Be an issue after a while. It seems like it will be to too heavy to be productive
Well what can I say ,you just bought a smile to an engineer ,well done .
The manliest thing I've ever watched in my life
Nothing screams a home improvement episode as this one!
Pretty awesome, and the exhaust blows away the shavings, too.
So, how hard is this on your hand? I cant imagine its very pleasant to hold for more than 10 seconds. Especially with the power of yhe torque, in the palm of your hand, but also with the vibrations.
I think you miss the flywheel to estabilize the rotation and increase the tork but the project is awesome
This man is too powerful... he's giving those "ls swap the world" guys too much inspiration to take the phrase literally.
Can't drill vertically for too long or engine will overheat, the pump started pumping air because all the liquid was on the other side of the tank. Still, very cool for a DIY project, it looks badass!
Maybe the most practical thing I've ever seen.
So funny how people can find something wrong with a one-of-a-kind thing. Like how they know it's supposed to last more than five minutes lmfao. This is by far the most American outside of the box shelf, shop talk kind of thing any mechanic or fab tech or shit I mean anyone really that does any type of work with their hands this is like a memorabilia type thing I would imagine but actually works to show off with once in a while obviously he you got other drills lol. Way impressive and hats off to ya most impressive indeed for sure. Keep on keeping on yo!!!!
That would be an instant classic in the Binford 2000 tool collection.
O.K. I f_cking love it !
Awesome little project! It does amuse me, however, that so many people think its more powerful than a battery drill. This is a great analogy for an electric car. Need a battery to turn a motor to start the inefficient engine that is loud, cumbersome, & more finicky to build & maintain.
Finally someone putting a model engine to use
It's LITERALLY, Tim Allan from "Home Improvement"! Seriously if you were in the show Tim would do his lil "HarHarHarHar" grunt when he's talking about giving a tool MORE power Haha. I absolutely Loooooove this!!
Man i really wish my brain worked liks this. I mean dont get me wrong i am not incompitant. But I am not nearly as skilled with things of this nature still second guess some of my work. I am just now starting to learn how to use a tape measure properly. I was horrible with math growing up.
that didnt start life as a drill but an impact wrench
You are a sick sick man and that's why we love you!
I LOVE how the exhaust is there to blow off the dust and chips!!!!!!!!!🤣🤣🤣🤣🤣🤣
0:44: YOU DIDN'T HAVE TO CUT ME OFF 🗣[Galaxy Brain Meme]
I’m pretty sure you are the only I’ve seen be able to get one those mini v8 motors to actually run proper let alone make it a drill.
very cool!!! the v8 looks cool on the drill. awesome idea !
Genius man for make the unique drill
Awesome!! Next you gotta hook it up with some forced induction and a flat plain crank!!
That would be perfect for a tool gear museum exhibit.
mmmm!!!
comodo, leggero, maneggevole, silenzioso, versatile, economico, ecologico, .......
...un attrezzo COMPLETO !
major flaw when u drill your starving the coolant causing it to over heat slightly until placed upright intake should be on other end exit is fine
i see at the end of the video you corrected that problem
I tinker with stuff a lot and have put together some crazy things but that is 100% awesome! I need it!
Only concern is you’re going to wipe out the thrust bearing on the crankshaft with all of the extra pressure
When you love the smell of gasoline but you are a machinist
I need this! Perfect for pre drilling holes in my drywall.