Just installed the hyperflash harness today on my 2002 C5 after replacing the old bulbs with new LED's. Turn signal is back to normal and it works beautifully! Great tip and instructions. Thanks!
Great install on the car. Although I have C7's on my end - love your video's and a chance to remember a few prior C6 and C5's that I have owned. Thanks for the walk down memory lane. Hope your new role as DAD is working out. Best Chris!
I like the "Corvette Envy C5 Corvette HyperFlash Harness" and was considering buying one. It looks a lot easier than wiring every light socket with a resistor. I know the Resistors you wire in at the lights get hot enough to melt plastic. Do you know how hot will this one gets stuffed into an already packed dash that the C5 has? I would really like to NOT burn my car to the ground because a fire starts under the dash.
How you hooked up your aftermarket tail lights i order some plug and play but when I turn my turn signal on the left and right and third brake light flash
I wish you was my next door neighbor I had a stroke four years ago I can't do things like that. I like those tail lights I got LED tail lights but just the bulb I got the hyper flashing too
Hi Phil, I had a traumatic brain injury about 16 years ago and the doctors were worthless. After 5 years of no help, I met a lady who got me taking Carlsons Norwegian Salmon oil and Puritans Pride Co-Q-10. These 2 vitamins took me from barely functional to 95+% of where I was before. And if you try them and they do nothing for you, they're only vitamins, not they won't do any harm.
Thanks again for another great video Chris, I just installed LED blinkers and brake lights, hyperflashing on both ofcourse If i install this will that address all my LEDs or do i need seperate hyperflash harness for seperate LEDs (blinkers\brakelights\ect.)
Hi Chris! So once you install the hyper flash harness the taillights wont be blinking as fast or they will? I have a C5 and think I am going to do this it looks great!!! Great video.
The new resistor in the harness corrects the hyperflash caused by the LEDs. If you have LED turn signals/tail lights, then you need this. If you have stock lights, you do not need this.
Great video Chris, thanks. I like to ask you about the steering wheel cover, where can I order it from, I know that your friend turned you on to it but you didn't say from where. Thanks.
Chris, I wanted to know if you experimented with LED HEADLIGHTS on the Corvette envy ACA headlight conversion you installed? Also I saw your AZ plate., I'm in Peoria where are you?
any idea why after install I get no blinkers or hazards? when I take it out and put it back to stock all works again just with the quick flashing blinkers
Hey Chris, great informative video. What are your thoughts on Corvette Envy Halo Headlights mod? Any chance you might do that mod to your car? How is mom and baby doing?
Does anyone know if these will work with incandescent bulbs? I installed it before I swapped the bulbs and neither the directionals or emergency flashers work. When I remove the module, they both work.
Heat does this product overheat ?? just bought a syneticusa led switchback . The square thing in-between the socket and light heats up I had it hooked up for five minutes and received burn on fingers . I keep haven to switch parking light housing , due to melting problems . and sockets get black and melting everything its around I have pictures of melted light housing if you like to see ? led 's don't get hot ? thats what I heard . does the hyperflash set up overheats at all , do led lights melt parking light housing . HELP .. Thanks Corvette life .. . One more thing " air pump check valve " is there another way to fix besides taking off intake manifold. Thats alot !! just to change an air pump check valve . thanks for your time and pls stay safe ..😁
@@mycorvettelife" its the resister" that heats up .. does the "hyper flash wire harness" (heat up?) Do you know anything about Air Pump Check Valves..? I need information on the secondary air pump check valve is there another way besides going through intake manifold .😁
I would be installing front bumper LED signal lights, I got flash harness similar to what you install for your tail lights. Will this take care of front signal lights as well? Thanks
I'm sorry, I read below that it needs one hyper flash like your install for all, however, I bought Halo tail lights with built in hyperflash, I assumed this is ok too?
So do you have to replace all the lights at once? Can I replace the front signals and do the back later and still install the hyperflash harness before the back?
@@mycorvettelife I already did but the light always come back.? And the code is p1571. Before I received the code p1111 from the air sensor but I already put a new one and deleted that code.!
Hey Chris! Great video. Question for you. Are you a teacher or have a teaching background perhaps? I’ve done some mods on my C5 similar to mods you’ve done and I find your stuff really helpful! I’m just asking! Cheers!
I have no break lights on my 02 C5. Turning singles don't work either. Thought it was the hazard module but it's not. Now I'm thinking this hyper flash harness may solve the problem. Just recently got halos...
@@gloy563 dude you've probably already fixed it , but it's most likely your turn signal stock .. there are some pins that get corrosion and don't make contact .. I took my turn signal stock off, made sure all the pins made contact at the contact points and them my brake lights worked again ..
Hey Chris, just installed front drl and side marker led bulbs in my 2001 convertible. Turn signals have hyper flash, 4 way hazards do not. Where you installed the hyperflash harness is the regular turn signal flasher there? I have old school heavy duty flashers and wondered if one of those might do the trick. We used to install them when we had trucks with trailers and would get hyper flash without an hd flasher. Thanks! mike
when I ordered my LED HALO tail lights I forgot to remove the option for the Hyper flash Harness, I already had one installed, so if anyone needs one for a C5 reply and I can get this to you for the shipping cost
I just ordered new housings and Leds for the DRLS and didn’t realize I needed this until now. If you leave me a contact email or number I can give you the shipping address and arrange to PayPal you the cost when it ships.
How you hooked up your aftermarket tail lights i order some plug and play but when I turn my turn signal on the left and right and third brake light flash
I like the "Corvette Envy C5 Corvette HyperFlash Harness" and was considering buying one. It looks a lot easier than wiring every light socket with a resistor. I know the Resistors you wire in at the lights get hot enough to melt plastic. Do you know how hot will this one gets stuffed into an already packed dash that the C5 has? I would really like to NOT burn my car to the ground because a fire starts under the dash.
Works flawlessly, EXACTLY what I needed for my corner signal upgrades. BIG KUDOS to Vette Lights and Corvette Envy.
Just installed the hyperflash harness today on my 2002 C5 after replacing the old bulbs with new LED's. Turn signal is back to normal and it works beautifully! Great tip and instructions. Thanks!
I’ve seen these advertised but never knew what they were for. It just shows you can teach an old dog new tricks! Thanks Chris👍🤠🇺🇸
Just wanted to say thank you!! My son and I installed and they look great!! Our father - son project is rolling. Please keep up the great work!
Great install on the car. Although I have C7's on my end - love your video's and a chance to remember a few prior C6 and C5's that I have owned. Thanks for the walk down memory lane. Hope your new role as DAD is working out. Best Chris!
Nice video! Clear and concise. I'm installing this today. Thanks!
Nice straight forward video. Thank you Chris!
Thanks for paying it forward.
You bet!
Ive said it before. I LOVE your videos. always helpful. Hope i get to show off my C5 soon.
Thanks for the DIY video! Lower dash piece was a bit of a bitch to fit snugly back on, but got it all done in 15min 👍
I just bought the radio Flyer luminator headlights and DRl with the angel eyes now I'm putting the Hyper Flash in now great video man thank you!
Thanks Chris, I just installed this last night. Corvette Envy has them on sale right now for $39.95
I went that route when I updated my front signals to LED's - better than the alternative
You installed the harness rather than the resistors?
@@alexislobo2010 yes
So does this work with front as well or do you have to install a different harness for front lights?
@@johnhaskins4452 this works for the entire system no need to get a seperate one for front, back, left or right
Pete Vit thanks just ordered :) change out to all led next weekend
Thanks! Halos will be my next upgrade so I'll need this item.
Thanks for the help chris on my c5.. keep the great videos coming...
Awesome video
Thanks!
Thanks Chris, more good to know info for the C-5 !
Great write up as always !
That was about as easy as it gets man. Nice!!!
Worked like a champ! Thank you Chris!
Thanks video helped although mine were all 7mm not torques
GREAT VIDEO. TAKE CARE
Tail lights look good Chris.
Well done video. Thanks!
Hi nice vid.
I need this thank you
I like the "Corvette Envy C5 Corvette HyperFlash Harness" and was considering buying one. It looks a lot easier than wiring every light socket with a resistor. I know the Resistors you wire in at the lights get hot enough to melt plastic. Do you know how hot will this one gets stuffed into an already packed dash that the C5 has? I would really like to NOT burn my car to the ground because a fire starts under the dash.
How you hooked up your aftermarket tail lights i order some plug and play but when I turn my turn signal on the left and right and third brake light flash
Does this single harness work for both front & rear turn signal indicators led bulbs ? Or Two harness required in one Vehicle ?
One harness for all.
I wish you was my next door neighbor I had a stroke four years ago I can't do things like that. I like those tail lights I got LED tail lights but just the bulb I got the hyper flashing too
Hi Phil, I had a traumatic brain injury about 16 years ago and the doctors were worthless. After 5 years of no help, I met a lady who got me taking Carlsons Norwegian Salmon oil and Puritans Pride Co-Q-10. These 2 vitamins took me from barely functional to 95+% of where I was before. And if you try them and they do nothing for you, they're only vitamins, not they won't do any harm.
Thanks again for another great video Chris,
I just installed LED blinkers and brake lights, hyperflashing on both ofcourse
If i install this will that address all my LEDs or do i need seperate hyperflash harness for seperate LEDs (blinkers\brakelights\ect.)
This harness does everything you need.
I’m about to the install on the led lights on my c5. I’m doing the front and back, will that harness work for all 4 corners?
Hi Chris! So once you install the hyper flash harness the taillights wont be blinking as fast or they will? I have a C5 and think I am going to do this it looks great!!! Great video.
The new resistor in the harness corrects the hyperflash caused by the LEDs. If you have LED turn signals/tail lights, then you need this. If you have stock lights, you do not need this.
Great video Chris, thanks. I like to ask you about the steering wheel cover, where can I order it from, I know that your friend turned you on to it but you didn't say from where. Thanks.
www.etsy.com/shop/RaceGripCo
Chris, I wanted to know if you experimented with LED HEADLIGHTS on the Corvette envy ACA headlight conversion you installed? Also I saw your AZ plate., I'm in Peoria where are you?
If you're running LED's in the front and regular bulbs in the back, would this have any negative effect on the regular bulbs?
No
any idea why after install I get no blinkers or hazards? when I take it out and put it back to stock all works again just with the quick flashing blinkers
Hey Chris, great informative video. What are your thoughts on Corvette Envy Halo Headlights mod? Any chance you might do that mod to your car? How is mom and baby doing?
Are you referencing the Projector ACA Headlights? If so, stay tuned. Mom and baby are great, thanks for asking.
Does anyone know if these will work with incandescent bulbs? I installed it before I swapped the bulbs and neither the directionals or emergency flashers work. When I remove the module, they both work.
Hi Chris, have you tried to install the Mustang type blinkers on your C5?
No
Heat does this product overheat ?? just bought a syneticusa led switchback . The square thing in-between the socket and light heats up I had it hooked up for five minutes and received burn on fingers . I keep haven to switch parking light housing , due to melting problems . and sockets get black and melting everything its around I have pictures of melted light housing if you like to see ?
led 's don't get hot ? thats what I heard . does the hyperflash set up overheats at all , do led lights melt parking light housing . HELP .. Thanks Corvette life ..
. One more thing " air pump check valve " is there another way to fix besides taking off intake manifold. Thats alot !! just to change an air pump check valve . thanks for your time and pls stay safe ..😁
No. If you have wires getting hot you have a problem.
@@mycorvettelife" its the resister" that heats up .. does the "hyper flash wire harness" (heat up?)
Do you know anything about Air Pump Check Valves..? I need information on the secondary air pump check valve is there another way besides going through intake manifold .😁
Where did you get your black defuser on the back of your Vette?
C7Carbon
I would be installing front bumper LED signal lights, I got flash harness similar to what you install for your tail lights. Will this take care of front signal lights as well? Thanks
I'm sorry, I read below that it needs one hyper flash like your install for all, however, I bought Halo tail lights with built in hyperflash, I assumed this is ok too?
Yes
Does this harness solve the Hyper Flash if you only put the Switch Back LED in the front DRL and leave the stock tail lights?
Yes
So do you have to replace all the lights at once? Can I replace the front signals and do the back later and still install the hyperflash harness before the back?
You do not need to replace everything at once.
@@mycorvettelife
Thanks!
I'm looking to update my 1997 and this is the first step. Enjoy the content.
Does it have inbuilt resistors that consumes lots of energy ? Does it drain car's battery faster ?
It doesn’t consume energy.
Where did your wheels go?
Took them off. I’m doing a few projects.
Could you just bend the contact inside the cars flash cube.
No
@@mycorvettelife i did on my 2003
Still getting harness but had to try.
Hey bro question I have a corvette c5 1999 I don't know why the traction light always turns on.??
Check the codes. Probably the ECBM.
@@mycorvettelife I already did it but I don't know if to change it oh leave it like that.!!
@@joseguevara1844 Clear the codes. If the light still comes on the code will appear. What code is it showing?
@@mycorvettelife I already did but the light always come back.?
And the code is p1571. Before I received the code p1111 from the air sensor but I already put a new one and deleted that code.!
@@joseguevara1844 Try disconnecting the battery for a few minutes to reset the computer. Does your TC work?
Hey Chris! Great video. Question for you. Are you a teacher or have a teaching background perhaps? I’ve done some mods on my C5 similar to mods you’ve done and I find your stuff really helpful! I’m just asking! Cheers!
No, not a teacher.
No tells you that that unit doesn’t fix the same problem you get if you turn your emergency flashers on. That uses a separate flasher unit.😮
Does it have over heating & melting issues ?
No, this harness has been used universally for 20 years now in the C5 world.
Is this strictly for hyper flash ? Can it solve any other problems ?
Such as what?
I have no break lights on my 02 C5. Turning singles don't work either. Thought it was the hazard module but it's not. Now I'm thinking this hyper flash harness may solve the problem. Just recently got halos...
@@gloy563 dude you've probably already fixed it , but it's most likely your turn signal stock .. there are some pins that get corrosion and don't make contact .. I took my turn signal stock off, made sure all the pins made contact at the contact points and them my brake lights worked again ..
Hey Chris, just installed front drl and side marker led bulbs in my 2001 convertible. Turn signals have hyper flash, 4 way hazards do not. Where you installed the hyperflash harness is the regular turn signal flasher there? I have old school heavy duty flashers and wondered if one of those might do the trick. We used to install them when we had trucks with trailers and would get hyper flash without an hd flasher. Thanks! mike
The hyper flash harness takes care of everything.
Just ordered one from Amazon, be here Monday. Thanks for the reply and your videos.
What is the price of this harness ?
Varies depending on where you buy it.
Corvette Envy has them on sale right now for $39.95
SWEEEEET!!!
when I ordered my LED HALO tail lights I forgot to remove the option for the Hyper flash Harness, I already had one installed, so if anyone needs one for a C5 reply and I can get this to you for the shipping cost
Pete Vit I’m interested
I just ordered new housings and Leds for the DRLS and didn’t realize I needed this until now. If you leave me a contact email or number I can give you the shipping address and arrange to PayPal you the cost when it ships.
@@joepetronglo7579 no problem Joe, contact me @ cvitullo@hughes.net , I'll check what the postage will be and respond to you
First.
How you hooked up your aftermarket tail lights i order some plug and play but when I turn my turn signal on the left and right and third brake light flash
Does this work for front and back signals? In other worde is one hyperflash harness all you need for front AND back turn signals?
I like the "Corvette Envy C5 Corvette HyperFlash Harness" and was considering buying one. It looks a lot easier than wiring every light socket with a resistor. I know the Resistors you wire in at the lights get hot enough to melt plastic. Do you know how hot will this one gets stuffed into an already packed dash that the C5 has? I would really like to NOT burn my car to the ground because a fire starts under the dash.
Doesn’t get hot at all.