Just watched this again, and am about to head out and try this in my coal forge with the quarters inside a section of 6" steel tube to try to keep the heat under control and not melt the quarters. Your video was extremely helpful!!!!
@@zjbknives Turns out my gas forge is the way to go. Coal works, but it's easier to control the heat with gas. Thanks again for the pointers, mine are coming out great!
When you're forging quarters it's pretty easy, because they're already layered with beautiful metals.. it turns out really awesome.. some other videos that I saw.
I just got done with a 13-14 layer piece. I alternated quarters and nickels. No welder. After watching this, I wanna try for the raindrop pattern. Good job man
Very nice work, just a side note, there is no moisture in your metal, H2O or moisture is a by-product of combustion as well as CO2, with the water vapor condensing on the relatively cooler metal. Once the metal heats up the moisture no longer condenses. A good indicator of temperature none the less. Nice tutorial, thanks for sharing.
Great video! You're already ahead of the game by having a real anvil to work on. I was never able to find a legit anvil, so I just ended up making my own from scrap steel and some 1.5" steel plate I found. I couldn't tell if yours is a cast iron base or if it's cast steel. If it's cast steel, you might want to take a good sharp drill bit and drill a hole at the ends of the crack that you have going up the side, and then at least weld up where you drilled. The drill holes will in a sense "terminate" the crack and help keep it from spreading further, even without welding them shut after. If you decide to do this, but don't know whether you have a cast iron, or cast steel anvil, the chips created when drilling will tell you a lot. If it makes basically a powder when drilled, It's cast iron for sure. If it makes small brittle chips, still most likely cast iron. (can't remember off the top of my head which does what, but grey cast iron, and ductile cast iron will behave in one of these two ways) If you have a good sharp bit, and you get chips that look like nice curls, and are flexible, just like what you would get from a piece of steel, then it's most likelycast steel, and can be welded just like any other piece of steel would be. Cast iron can still be welded. I don't care what anyone else says to the contrary, because I,ve done it myself, but for a repair on something that has the mass of an anvil, and just by the nature of it's purpose, is going to have to endure sharp impacts repeatedly, brazing would be the best bet. Also, If you do braze it up, you could grind it back down flush so you can see the shiny gold filled crack, and name it the "Liberty Anvil" lol. Keep up the good work man. You're on the right track with content, as well as editing. I've seen videos from creators that have been doing it much longer, that don't come off as well as your first video has. Also one last thing from a mutual hater of any flying stinging insect (honey bees excluded of course), here's a protip. If you're not around a source of ignition IE your forge lol. A can of el cheapo walmart carb cleaner will quite literally drop a psychotic, out for blood wasp or hornet, mid flight, right to the ground, and almost immediately thereafter, dead. Just don't use on bees. They only sting to defend or protect, and they make delicious honey, and polinate needed plants. Wasps on the other hand, were only created to fuck up your day, and there is no convincing me otherwise.
Yah Zane, very well done! I'm very interested in Makume Gane and cant find much content and really no good instructional information on TH-cam. You might have found your niche. I'm not kidding.
Funny. I've made some damascus by hand (which btw is a pain in the ass and very time consuming if you dont have a press) so figured this would be simple to do with softer materials but had absolutely no success and ended up wasting $10 worth of quarters. had them nice and clean, wrapped them with wire exactly like in video then proceeded to throw in forget. once I had everything up to temp I started hammering quarters and looked like they were nice and welded. tossed back in forge to get back up to temp and 1st hammer blow to them after 2nd heat cycle the quarters all blew apart. tried it twice and both time quarters just blew apart. idk wtf happened but gonna try again and if same thing happens I'm done trying to make the shit because I'm not gonna keep wasting money away that can be spent on other things. Lol
Absolutely brilliant vid.Congratulations.But I got a few questions.I'd prefer to make a bracelet.So I would need to finish with a bullet six and a half inches long by one inch wide using copper, brass,nickel and silver disks(to stay close to your pattern).Do you think this would work?.Thanking you in anticipation.
That sounds awesome! And i do believe it can work. I’ve usedwith all of those metals before in mokume, and my only hesitation is the brass, it doesn’t like to play nice with the other metals at high temps. The biggest factor in forge welding mokume is making sure the involved metals have a similar melting temperature. Other than that, have fun! Feel free to message me with any questions
Why, there wouldn't be a copper layer to make the pattern. Plus the nickel on the quarters make a good "silver" look without the price. And half the work is done for you at the mint!
When you squared it up did it delaminate? And then you just heated it up more pounded it back together? I cannot get passed the delamination it’s devastating every time I’ve gotten like billets I guess but when thrown on the ground or just tapping it it never sounds like one solid piece it drives me insane
It always delaminates when I forge it on its side, I just get it back up to forge welding temp and reset the welds. It’s a pain but you can have success in the end. Just make sure you finish off your billet by getting it to FW temp and setting the final welds on the piece. This helps make sure everything is sealed up in the end
Ive struggled with delam aswell.... ive read about omce you set the initial weld you can grind the edges off to get rid of all the knerling and it helps... have you tried that?
I wish! The reason I use quarters is that they have a copper core with a nickel coating. That’s what gives the looks of alternating layers. Nickels are one solid metal so wouldnt give the same look
@@JR-pj8pz that’s true, but they are mixed together as a homogenous metal when quarters are separated layers. Doing this with Nickels just give you a silver colored billet
saw another video of a fella with an electric crucible that does 760 c with a steel compression bracket. cool to see someone just use backyard blacksmith stuff and get a good result... at least apparently. how many delaminated billets did you go through before getting a good one?
Charlotte, NC in the house!!!! I've been a hand engraver for over three decades, and have gotten into jewelry making. Thanks for your video.
This is the best video I've seen on making mokume gane thank you you did a great job
Mercury Smoothy thank you very much! If you need any additional info please don’t hesitate to reach out.
Excellent video very straight forward
Nice. Blow torch to bring out the pattern was cool. Never seen that before.
Great first video!!!! Thanks for sharing
Awesome great video and website guys!
Thanks Zane, sounds really beautiful 👍💫🙋♀️
Just watched this again, and am about to head out and try this in my coal forge with the quarters inside a section of 6" steel tube to try to keep the heat under control and not melt the quarters. Your video was extremely helpful!!!!
Bryson Alden that’s a great idea! Glad I could help
@@zjbknives Turns out my gas forge is the way to go. Coal works, but it's easier to control the heat with gas. Thanks again for the pointers, mine are coming out great!
Great video! Very well done. A real craftsman.
When you're forging quarters it's pretty easy, because they're already layered with beautiful metals.. it turns out really awesome.. some other videos that I saw.
I just got done with a 13-14 layer piece. I alternated quarters and nickels. No welder. After watching this, I wanna try for the raindrop pattern. Good job man
great job Zane and significant other! Keep up the good work!
My daughter gave me one of your knives for Christmas. I have thoroughly enjoyed it, and your craftsmanship is evident! Keep up the good work!
Nice craftsmanship! That would make a beautiful guard.
Awesome video bro 👍 especially for your first time 👏🏻👏🏻👏🏻
Great job! Very informative
NICE!!! You're a stud
@@donpettyandthespacefakers1798 both!
This is awesome! That mokume came out looking great!
Sweet! Always love seeing your work.
That’s awesome! :)
WOW.!
Man that is a very impressive billet made out of the simplest metal everyone has.
looks gorgeous. KUDOS.
Very nice work, just a side note, there is no moisture in your metal, H2O or moisture is a by-product of combustion as well as CO2, with the water vapor condensing on the relatively cooler metal. Once the metal heats up the moisture no longer condenses. A good indicator of temperature none the less. Nice tutorial, thanks for sharing.
Congratulations on your new channel and website!
Really nice video, actually had no idea how mokume was made.
Came to win free stuff...stayed for the great ambiance.
Nice job!
This is really interesting! I love how you broke everything down so simply!
Great video! You're already ahead of the game by having a real anvil to work on. I was never able to find a legit anvil, so I just ended up making my own from scrap steel and some 1.5" steel plate I found. I couldn't tell if yours is a cast iron base or if it's cast steel. If it's cast steel, you might want to take a good sharp drill bit and drill a hole at the ends of the crack that you have going up the side, and then at least weld up where you drilled. The drill holes will in a sense "terminate" the crack and help keep it from spreading further, even without welding them shut after. If you decide to do this, but don't know whether you have a cast iron, or cast steel anvil, the chips created when drilling will tell you a lot. If it makes basically a powder when drilled, It's cast iron for sure. If it makes small brittle chips, still most likely cast iron. (can't remember off the top of my head which does what, but grey cast iron, and ductile cast iron will behave in one of these two ways) If you have a good sharp bit, and you get chips that look like nice curls, and are flexible, just like what you would get from a piece of steel, then it's most likelycast steel, and can be welded just like any other piece of steel would be. Cast iron can still be welded. I don't care what anyone else says to the contrary, because I,ve done it myself, but for a repair on something that has the mass of an anvil, and just by the nature of it's purpose, is going to have to endure sharp impacts repeatedly, brazing would be the best bet. Also, If you do braze it up, you could grind it back down flush so you can see the shiny gold filled crack, and name it the "Liberty Anvil" lol. Keep up the good work man. You're on the right track with content, as well as editing. I've seen videos from creators that have been doing it much longer, that don't come off as well as your first video has. Also one last thing from a mutual hater of any flying stinging insect (honey bees excluded of course), here's a protip. If you're not around a source of ignition IE your forge lol. A can of el cheapo walmart carb cleaner will quite literally drop a psychotic, out for blood wasp or hornet, mid flight, right to the ground, and almost immediately thereafter, dead. Just don't use on bees. They only sting to defend or protect, and they make delicious honey, and polinate needed plants. Wasps on the other hand, were only created to fuck up your day, and there is no convincing me otherwise.
The military actually used to do that for cracks in airplanes’ airframes. I don’t know if that’s still done.
Absolutely gorgeous!!! Need to try this👍🏼
Beautiful, you made it look so easy process buddy.
Yah Zane, very well done! I'm very interested in Makume Gane and cant find much content and really no good instructional information on TH-cam. You might have found your niche. I'm not kidding.
Awesome pattern 🗡️
Proud of you man! Loved the video!
Nice job Zane dude!! Can’t wait to see more of your work and how to videos.
I saw it called a rose Damascus when the pattern looks like if you're looking down at roses
This was a great help. Just made my first billet last night. Keep up the great content! 🤘🔥
Good work man. Love what you're doing!
I’m gonna start using the heat method to bring out the pattern, I really like the color it gave the copper. Thanks for the video!
Great first vid man!
Looking good bud. Nice editing, good lighting. Glad you're on here.
Nice work
Very nice video !
Woo 700th like!
I loved the editing! Video was very professional and I like the intro! :)
Don’t quench it makes it brittle prone to delamination.
What kind of wire do you use in the first steps to forge weld
See you at Blade Show ...
You look like the human version of Anonymous.
Great video
I went and learned something.. neat
Dude, I just got into seriously making knives and couldn't get a handle on Mokume, thank you. I'm using it on a dagger I made today! You got my sub
where did the two different colors come from if quarters are one metal?
They arnt. Look closely at the edge quarteres after like 1967 are copper with a nickle shell
👍 super
Are you drilling the second set of holes on the same side as the first?
Can you do the same with layers of gold and silver to make a bangle
That piece turned out great. Love the pattern. Well done. How can I buy some from you?
Thank you very much! If you’d like some, shoot me an email at zaneburch.knives@gmail.com
Really diggin it, how about some silverware? May be challenging but I think you could pull it off! Love keepin up with your work bro
Funny. I've made some damascus by hand (which btw is a pain in the ass and very time consuming if you dont have a press) so figured this would be simple to do with softer materials but had absolutely no success and ended up wasting $10 worth of quarters. had them nice and clean, wrapped them with wire exactly like in video then proceeded to throw in forget. once I had everything up to temp I started hammering quarters and looked like they were nice and welded. tossed back in forge to get back up to temp and 1st hammer blow to them after 2nd heat cycle the quarters all blew apart. tried it twice and both time quarters just blew apart. idk wtf happened but gonna try again and if same thing happens I'm done trying to make the shit because I'm not gonna keep wasting money away that can be spent on other things. Lol
What kind of wire do you wrap the quarters with
Stainless steel wire
Absolutely brilliant vid.Congratulations.But I got a few questions.I'd prefer to make a bracelet.So I would need to finish with a bullet six and a half inches long by one inch wide using copper, brass,nickel and silver disks(to stay close to your pattern).Do you think this would work?.Thanking you in anticipation.
That sounds awesome! And i do believe it can work. I’ve usedwith all of those metals before in mokume, and my only hesitation is the brass, it doesn’t like to play nice with the other metals at high temps. The biggest factor in forge welding mokume is making sure the involved metals have a similar melting temperature. Other than that, have fun! Feel free to message me with any questions
Can that be used to make a strong blade or is it just decremental?
Do one with silver quarters
Why, there wouldn't be a copper layer to make the pattern. Plus the nickel on the quarters make a good "silver" look without the price. And half the work is done for you at the mint!
Absolutely gorgeous. I've just started getting into Mokume. Is there a chance I could purchase a billet from you?
I am liking your work. We need to get together and swap ideas. I live on the nc coast about 4.5 hrs from you.,
What’s the process if you throw some 90% silver quarters in the mix
Amazing work as always, bud.
@known.texan
When you squared it up did it delaminate? And then you just heated it up more pounded it back together? I cannot get passed the delamination it’s devastating every time I’ve gotten like billets I guess but when thrown on the ground or just tapping it it never sounds like one solid piece it drives me insane
It always delaminates when I forge it on its side, I just get it back up to forge welding temp and reset the welds. It’s a pain but you can have success in the end. Just make sure you finish off your billet by getting it to FW temp and setting the final welds on the piece. This helps make sure everything is sealed up in the end
Also sorry it took me like 5 months to get back to ya brother😅
Ive struggled with delam aswell.... ive read about omce you set the initial weld you can grind the edges off to get rid of all the knerling and it helps... have you tried that?
It is best to have music and voice at the same volume.
Here from green beetle
I was gonna be so upset if the ending wasn’t there
Good idea. Get rid of the music, or at least turn it down
Ah yes, the perfect material to forge the ultimate yandere weapon has been revealed. Sugoi 💯.
Great vid! Wasn't familiar with this material or method, and it's cool seeing how this stuff happens. @sv650n03
Records self breaking the law lol
Why wouldn't you use nickels? It would be WAAAAAY cheaper
I wish! The reason I use quarters is that they have a copper core with a nickel coating. That’s what gives the looks of alternating layers. Nickels are one solid metal so wouldnt give the same look
@@zjbknives US Nickels are 25% Nickel, 75% copper ;) which is actually a stronger alloy than the quarter / dime / half dollar composition.
@@JR-pj8pz that’s true, but they are mixed together as a homogenous metal when quarters are separated layers. Doing this with Nickels just give you a silver colored billet
@@zjbknives ah. Now that makes sense!! ;)
That whistle music is awful! Otherwise good content! Thanx!
Isn't it illegal to destroy money? I'm from south Africa and its against the law here.
шляпу подари
WHY EVERYBODY ALWAYS PUTS MUSIC TOO LOUD COMPARED TO ALL THR TALKING?
SO FUCKING ANNOYING !
officially, destroying quarters is a felony....jus sayin'.
If I was being “fraudulent” while doing so then yes, but this is for artistic purposes and therefor legal
@@zjbknives money is federal property, always.
It's destruction is illegal.
Not saying I'm not gonna do it, but I'm also not gonna post it.
I have had numerous people ask me about this so I’ve done my homework:)
Federal statute 18 USC 331 is what I’m basing this off of
saw another video of a fella with an electric crucible that does 760 c with a steel compression bracket.
cool to see someone just use backyard blacksmith stuff and get a good result... at least apparently.
how many delaminated billets did you go through before getting a good one?
Nowadays I have very few failures, in the past I would get a failure every once in a while. It happens during the brazing process
What kind of wire did you bind the stack of quarters with ?
Can I ask what type of wire did you use to secure the stack?
Hey brother, I use braided steel wire! The same stuff used to hang picture frames up:)
@@zjbknives Thank you!