5 second to 10 hour timer delay circuit | make a timer delay circuit controller using 555 timer ic.
ฝัง
- เผยแพร่เมื่อ 3 มิ.ย. 2020
- 5 second to 10 hour timer delay circuit | make a timer delay circuit controller using 555 timer ic.
FB Page: 110941940578...
If you have enjoyed This video then please like, comment and don't forget to subscribe.
Thank you for watching.
Welcome to my channel "MonoTech Master"
#Timer_delay_circuit
#555_timer_ic_project - วิทยาศาสตร์และเทคโนโลยี
Agar 3 minute ka time delay kre to 3 min. Ke bad on hoga fir 3 min. Kr bad off hota hai.?
Change the capacitor valu
Great job. Acha agar hamey is circuit ko 12 volt supply pr use krna ho to ham is circuit main kia changing Karni? Kon SI cheez change Karni Hogi ya value change Karni Hogi? really must plz
Thanks?
V.god.veery.simple
Thanks
Just what I was looking for. Thanks
You welcome
বাংলাদেশ এর ভাইদের জন্য কমেন্ট টা রাখে গেলাম ❤️
হ্যা ভাই এটা আসলেই কাজ করে আমি নিজে ট্রাই করে দেখছি । আপনি ও ট্রাই করে দেখতে পারেন💕
অনেক অনেক ধন্যবাদ ভাইজান♥️
আপনাকে ও অসংখ্য ধন্যবাদ ভাই 🥰💕
❤️❤️
It was a beautiful work, you talked about a 10-hour delay in the description of the clip, please tell me how you will reach this delay in the connection. Thank you very much.
Change your capacitor.
Which capistor we can use ?
555 is good for about 10 minutes and delay timer more 10 minutes is very telorance . with capacitor more than 470uf make not good timer
@@user-jp4lr6lv1l what type of capacitor would you recommend for a one hour delay?
Can you tell me why you shorted the variable resistance and ground of the pot
Very slowly rotate variable resistor
If I were to use a 5V TTL Logic Or IC or a CMOS Logic Or IC Output as Input to the Electrolytic Capacitor (+) Input with the Capacitor's (-) to the Resistor and Pins 2 and 6 INSTEAD of a Momentary Power On Switch to Pin 8 and the Capacitor (+) as wired, then tie Pin 8 to Vcc instead, would an Or IC Output Hi (5V/12V) trigger the 555 Delayed Pin 3 On Timing and keep it On until the Or Output goes Lo (Ground), which (I hope) would turn the 555 Pin 3 Hi Off/Lo (Ground)? Is this another way the 555 can be Triggered and Turned Off? And would that Low (Ground) fully discharge the Electrolytic Capacitor quickly in a safe way, making the circuit and 555 fully ready for the next Or Hi Input with no reduced timing from a partially charged Capacitor? I don't yet know the Voltage used by the device for the lights/LEDs which I will use as Or Inputs, but a 555 works with between 4.5V to 15V, ao this circuit should work fine for my application, but I may have to use a CMOS Logic Or IC instead of TTL. Thanks
Most welcome
@@MonoTechMaster You did not answer my question. Can the 555 be Triggered for the Delayed On with an Or IC Hi this way and will the Or IC Low reset the 555 Pin 3 to Low by discharging the Capacitor fully and safely with the 555 always connected to Vcc Power on Pin 8 and Ground on Pin 1 while the device to be timed is turned On? Voltage and Ground will be obtained from the device to be Timed, either 5V or 12V.
I tried with C 100uf and R50k, the light stays on and doesn't turn off, the voltage is 12 volts, what's wrong?
No
@@MonoTechMaster no? soo?
Dear Mono Tech Master,
Nice circuit. What is the maximum output wattage ?
Regards Paul - Malta Europe
thanks
5w
@@MonoTechMaster sir i want the paper diagram of this circuit. Could you please provide me this?
People asking where you going he always reply what he eat yesterday 😂
Thanks
Does it loop endlessly
Sir.. it is very much interesting to do
What is the maximum delay time
And it can survive long time..or not
yes
thank you
Perfect output , Great to share your idea here , Thank you
most welcome sir.
can i use IN 4007 diod for relay coil??(555 ic between pin 1 and 3 )
Can try.
Thank you.
Nice one. Good work
Thank you so much.
Dear. Great project. Is it possible to decrease the time to 2 or 3 seconds? Thank you very much
yes posible.
thanks
Hello brother.
Ye Jo circuit aap NY banaya hy isska maximum delay time kia hy?
Yani potential meter ko full open Karne ke baad nimium time kittna Hoga?
Move to Potentiometer
Good job, pls, Can I use 12V Battery for this circuit?
Yes
Can I use this delay timer circuit to the stabilizer for refrigerator.??
yes.
thank you.
Can the timer run with 12v same as the relay? for example to turn on a 12v fan. thank you
try to it Thank you
The max r and c are 10M and 470u. So max delay is 1.5 h
Plice try to it.
Thank you.
Please, must it be a push bottom switch, can the switch be connected together for a long time?
ok sir next time.
thank you.
If i want 5sec delay fixed. Then what amount of resistor should use?
1k
That is a very tough 555! no limit resistor on the LED or protection diode across relay coil.
Yes.
You used a 6 volt relay. Power is 9 volts. If I give a power of 5 or 6 volts, will the relay work?
If I want to design the circuit for an hour time delay, what do I have to change - capacitor or resistor? And what would be the changed rating?
If you want to reduce the time, you need to change the value of the capacitor.
T=R*C
Bro thank you so much bro
You welcome
Mono how to posible positive wire only connect push switch. Annd circuit will work properly?? Mai bhi bhi confuse hu k begair positive supply k relay work kaise kiya??
Yes
Cau give us formula about delay before the led on? Tx u sir
Thankyou sir
welcome sir.❤️
Thanks sir.Very useful for me.
#2:00 when LED light on , how long it take to light off?
Thanks.
You can turn on the potentiometer and set the time as you wish. Thank you sir
@@MonoTechMaster Thanks sir
Welcome sir place subscribe my channel
@@MonoTechMaster done sir
❤️
Dear mono tech can i use this on stabilizer?
Yes
Can we fix this without switch kindly suggest i need 3 sec on dealy timer and supply will be there continue connnet
yes sir.change your capacitor value.
Excellent project. How could we get the schematic?
Yes❤️❤️
If you watch the video properly, you can make it like this
Can we use 500 uf capictor or less for decrease time for 3 sec
Try to it.
Excuse me, if I want it to be 10 minutes max, what should I do?
please Rotate the potentiometer.
Put the potentiometer on a board, then put a knob on it and a physical barrier that it cannot pass, or get a potentiometer with less ohms.
From where I can purchase it?
Dear: Great project. Can the time be less than 5 seconds? Thank you
ok flow my channel
Yes it can, just change the cap and resistor values
Thanks you !
Hello bro
Agar iss circuit main 12 volt ki relay lagani ho to kia Laga saktey hen?
If I want use 12 volt relay in this circuit how it possible?
Propar connection
Kya 9v battery ki jagah 12vdc supply de kakte he
yes, max 12v for ic.
Sir kya ye set time pr auto on off bhi hoga
yes sir
May I download the video to watch it at my own pace? I already hit the thumb up :)
Ok sir
Circuit starts after 5sec and then off after 5 sec...I want switch to start after 10 hrs and off after 10 min then after that again start after 10 hrs again for 10 min is this possible? How can we do this??
next poroject.
Iwant on my motor 8 clock upto 9 there after should off one hour,, is it possible in it
It is possible to use a timer instead of a reel, which I have little idea about.
Thank you
How to 5-10 second on and 2 hours off regular plese make a circuit .
Sir i need 10 sec fix which component need to change and what value
Change your capacitor valu.
Is it off automatic or manually off
Automatic
On Ka h ya off Ka bhi ho inbuilt cercat
Automatic on off circuit
I want 6min delay time so which components value use please tell me sir
I haven't checked it out properly but I'll upload a video for you later.
Thank you sir.
कितने मिनट तक सेट कर सकते हो सर ईससे
Thanks
I want to know 10 minutes interval may light on hona and light on stand by 1minute what can i do
yes next project make it.
In the photo you show it connecting to a monitor, how is that done? Thanks
yes sir.
Thank you
@@MonoTechMaster can you tell me how to connect it to a monitor?
@@IH1940HAY use relay
Nice work!!!
Thanks bro
What is off time
5sec late
After 1 minute when the light is being switched on, then how long the light can stay on, is it for unilimtted
Yes
@@MonoTechMaster it will turn off after another 1 minute or after the power source is cut off?
is it dangerous using Relay on 220V? I feel some scared.
There is no fear of being able to use a relay on a 220 volt line. However, you have to use a high ampere relay.
It's okay, just connect the relay correctly - don't confuse the live pins with the coil pins - and for extra protection against coil back EMF add a 1N4001 diode in parallel with the coil, in a way that the 1N4001 doesn't short circuit the 555 output (with the diode stripe connected to pin 3 of 555, if pin 1 is also used for output).
Having added that, I doubt this lonely 555 timer will get to 1 hour, let alone 10 hours.
Also, 220v grid requires half the amperes of 110v grid, for the same power: P=I*U (example 220W=1A*220V while 220W=2A*110V)
Hello, I have a question: is it possible for him to be ignorant of her more than 10 hours approximately 72 hours
How can that be?
yes posible
@@MonoTechMaster Okay thanks, but would you recommend that I change the capacitor
What type of switch is that
Potentiometer
What type of switch Please (Push to on or Direct on type)
Try to it.
Its possible do 1second on, 1 second off loop 12v from this? how?
Yes possible sir.
@@MonoTechMaster What I have to modify?
You can turn the potentiometer and set the time as you wish
Nice video. Will a smaller capacitor reduce the time the light stays on? What value capacitor will I use if I only want the light to stay on for a half a second?
Thank you
Yes sir.
Thank you
جيد احسنت
Thanks
The key you are using is push or on-off?
try to it.
thank you sir.
on off
It is basically ON delay timer. I want reverse function i.e. OFF delay timer.
ok thank you sir
Alright man I’ve got you a link to an easy video of an off delay timer: (th-cam.com/video/ZHsUC4fYw8c/w-d-xo.html)
You have two simple solutions:
1) use a relay with 5 pins instead of 4, and choose the normally closed (NC) pin for your project
OR
2) use pin 3 of 555 and the current source positive (+) as output
Please tell me how much volt of Riley
6 Volt Riley sir.
Thank you.
Ac current se chalne wala banno
Thanks
what is voleum
10k potentiometer
bhai kia yai circuit 10 hr tk delay kr sakta hai?????
kus nahi bhai.
Thank you.
Hello, when I want the time to get longer, you advise me to change the capacitor or resistor
Doesn’t reply. Anyway dude you have to change both the capacitor and resistor values to increase the time delay.
@Idris Callan You are absolutely right, nobody gives a shit!
@@teku3985change the resistance value
FIGR ME PRCHHAIN AA RHI HAI SIR
Thanks
hello can you do in 555 timer 5 sec off 2 sec on?
Yes
Ohhh that would be a great help. Thats what i want to know also
Wow
Thanks bro
I need 5 min time delay. Can u plz suggest me anything.
You can do this by turning the 100k potentiometer used in the circuit in 5 minutes.
thank you.
Hello. How can I calculate the specific resistance for a certain time? I need a 5.5 hours timer
yes sir.
thank you
for 5.5 hour you will need 4700uf capacitor and 4 Mega ohm resistor(or you can use 4x1M Ohm resistor in series)
for easy calculation, use this calculator,
www.allaboutcircuits.com/tools/555-timer-monostable-circuit/
@@vu4991 can I reverse the function? Say I want it to run for an hour then have it turned off after? Thanks!
@@snobergarden131 yes, you can connect to Normally open connection of relay to do that.
Can I use 12v adapter instead of 9v battery
Can you reverse the operation so that the light stays ON for x amount of time instead of a delay?
yes sir.
Thank you
सर मन चाहे time पर अन अफ होता रहे एक सर्किट बनायिय प्लिज
yes sir thank you.
how to set it for few hours? you didn't show that
On next time
Thanks Bhai please provide. Circuit diagram
welcome bhai.
@@MonoTechMaster please provide circuit diagram .. bhai
Good
Thank you sir
How do you make off timer?
Yes
Kinldy provide the paper connection diagram of this circuit?
yes.
thank you
@@MonoTechMaster then please give me
Draw schematic diagram is better .
Thanks
Thank you so much
Time delay is ok but i want bulb on fir 1minute what can i do
yes sir❤️
Is it really possible to get 10 hrs with this?
No sir but try to it.
how i can fix on 2hrs without voleum 100k and make it repetition
yes sir.
what is the max delay time
Sorry sir I can't say the right thing you can check
It's in the range of single digit minutes, and it varies with every power up
How can it work for 3 hr timer
yes
@@MonoTechMaster what YES. Are you joking. Explain him, how can it work for 3 hours.
use this calculator,
www.allaboutcircuits.com/tools/555-timer-monostable-circuit/
1.1*R*C
Kyuki capacitor me only 0 to 5mint tak hi power rhti hai
charge your capacitor value.
Thank you.
I want 240v cut off timer video.cutoff range 5 hours
Move your potentiometer
I want to do the exact opposite.. Once it's triggered I want to add timer to auto reset
Sorry sir, I didn't understand your word properly. Please explain a little more.
Thank you.
@@MonoTechMaster uh.. As you showed.. When you press button. Led turns on in the given timer ryt. I want to turn of the LED with timer. Not turn on
Depending on the time of making such a project, I will try to make such a project in future.
Thank you.
thinks
Welcome
Bon schéma
❤️❤️
Where is your circuit diagram?
ok next time
thanks
ভাই এই সার্কিটে লাইটের + -- এক করলে লাল হয় না কেন ।কি করলে লাল হবে ।বলতে পারবেন কি????????
dakta hobe via
@@MonoTechMaster please please vai aktu dakhan .
how do i get 12 hours
?
Use Variable potentiometer.
Automatic on off ni hota
yes sir.
But with 100k potentiometer, it will not give 10 hours.
Thanks
Yes ; you are right .
So what do you advise now, what potentiometer capaicity can be used for 10 hrs? 6 hrs....
plzz plzz plzz replay 🙏🙏🙏
Inbox plzz
how to turn off after 1 minut
You can turn the potentiometer and set the time as you wish
Excelente para una bomba xd
thank you