Does your Ice Level Sensor Work? This is What it is Supposed to do
ฝัง
- เผยแพร่เมื่อ 10 ก.ย. 2024
- Call us today with you model number and we will make sure you get the right part
888-655-8569
In most cases we can get you the part the next day if ordered before 4pm central time.
---------------------------------------------------------------------------------------------------------------------------------------------------------------
OEM Emitter and Reciever- amzn.to/3dfPpeF (Orignal Replacement Part)
After Market Part- amzn.to/2XFVPxj (Way cheaper worth the risk)
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Donations are appreciated you can donate here - www.paypal.me/...
--------------------------------------------------------------------------------------------------------------------------------------------------------------
My Camera Set Up gear
Go Pro Hero 8--amzn.to/3lnXIcz
Go Pro Hero 8 w/Accessories - amzn.to/3eSLvdf
-------------------------------------------------------------------------------------------------------------------------
Stop by our Amazon store to pick up must have tools for appliance repair
www.amazon.com/shop/beardedappliancerepair
--------------------------------------------------------------------------------------------------------------------------------------------------------------
This Video will help you understand how your emitter and receiver or ice level sensor works on you Whirlpool or Kitchen Aid Refrigerator. The Light goes solid when the IR sensor is not being blocked by anything and will blink when it is being block. This video also shows you how to cycle the ice maker. You need to get power to it first and what you do is: Unplug the fridge for about 30 second and plug it back in. open the freezer door and the light will be off. If you close the light switch you will see it blinking. This tells you that the emitter and receiver is sending power to the ice maker and you can cycle it from there. Hope this helps you all out there.
The video helped to understand we may be able to do our repairs ourselves. We have a whirlpool brand ice maker in a Kenmore side by side that is now seven years old and just quit last week. So for Father’s Day I have been surfing the internet and your kind voice helps. Thanks, Sarah
Great Troubleshooting. I searched the internet over and over looking for good simple info and couldn't find crap. Your video was very helpful. I ruled out my emitter/receiver and now know I need an ice maker. Thanks again for a great video.
Why are there some negative reviews? Complaining, he just showed a very informative video, watched it twice,easy to follow and understand,so if you don't get it,HIRE SOMEONE 😂
Thank you for the video. The Multimeter demo told me what I needed to do. New Thermistor is in and running fine. Been a good week. Just replaced the Heating Element in my Samsung Dryer.. Loved to know what I saved doing it myself..
Thanks for the video and tips on resetting this type ice maker. Near as I can tell, mine some how got out of cycle and added water with cubes still in the ice mold. This resulted in an ice plug in the filler cup and water spraying inside the freezer. I removed the IM to clear the ice plug and the mold. Since no parts looked broken I put the IM back and it filled. After over 24 hours, the IM wouldn’t eject the cubes. Then I found your video and removed the IM and followed your steps to reset the IM and cleaned the sensors. It worked for me and the IM ejected the cubes and is back working. Many thanks!
I ordered the off brand ice maker sensor replacement, thanks for pointing that out!
Do I need to unplug the fridge to swap it out, or can I do this with the fridge powered on?
Have you watched this video? In the video it sounds like you know what you're talking about but it was hard to follow because the camera was all over the place. At times, it looking at top of the refrigerator. Place this video again but please be more aware what the camera is looking at. Thank you.
Once you have the cover off, measure the location of the water flow-time adjustment screw and mark that location on the cover. Then after you've finished, if it needs adjustment again, you won't have to take the whole ice maker out just to adjust the water fill time. You can cover the hole with a good quality tape or a small rubber plug if you want to.
Thank you. The oddest little piece of ice blocked one of the teeth.
Hello thank you so much for the very informative video, I did replace the water valve yesterday and the icemaker was replaced about 3 weeks ago so it's brand new, the problem is that after replace the water valve it didn't start making ice, I did what you said recalling it by using the jumper wire and it seems to work fine, it did cycle fill up water and it cleared the ice later on, then it filled up with water again but now it just ice and no second batch of ice. Any advice what else to look for? in other words only worked one full cycle once. and thank you again for the videos and thank you for helping people out
Thanks for your great videos. I'm not brave enough to jump my ice maker but the sensor info was very helpful
My red light on the right inside of the door… on the little control panel… is blinking all the time. It doesn’t go out like you mention in this tutorial video. However, the power was turned out for our area by the electric company one night. Perhaps that caused my ice maker to stop working. What do you think? I want to unplug as you did… just need to find a strong man to help me.. or several lady friends.
I have a whirlpool Ed5Fhazva03 side by side I need a replacement ice door flap and filter that's not a arm and leg
Thank you for taking the time to make the video. But I looked up the wrong kind of ice maker. Your video is very informative, For that ice maker and other ones like it
So i checked my sensor.. all good. I changed my water filter on the bottom of the fridge and thats when things stopped working. It just stopped producing ice. Now it did drop 1 tray of ice but it took 4 days to do so and it hasnt since which its been several days. There is ice frozen in the ice maker but its not dropping.
Should i jump it.. unplug it and restart it?
What should i do?
Hello I'm new here, just got a used Whirlpool ED5Fhaxva03 side-by-side and just hooked up the water and ice maker, can someone tell me how long it takes to make ice
Thank you very much .
Good video. Thanks. But,,,,,, what if the light on the right flashes when door open, solid when flapper switch on left is depressed and no 120 vac across L and N on the ice maker tray…. Where do the ice maker tray wires come from. AND I have already replaced the ice maker tray assembly. Is there a fuse coming to the tray?
I have an ice maker that I replace today in my Whirlpool, it looks just like the one in your video. I replaced it because it was leaking water all down the sides and food below. Too early to tell at this point, I am watching to see if replacing it worked or is the sensor telling it to fill and it over fills, how would I know?
Same type of refrigerator we have not making ice replaced the ice maker started to make ice again for about 5 days than it stopped again , any suggestions or ideas for the fix . Also was wondering if the red light stays on when you close the freezer door
Is there way to turn off ice maker? Pipe in back broke so I shut off water. The thing is, it keeps trying to get water. Most new ice maker can be shut off, I can't find a way?whirlpool gold model gc3shexns16 about 13 years old. Looks just like this one.
Thanks for the video Brother! Is their suppose to be a light beam where the flap is or is it just a receiver?
The status light on our fridge never blinks or lights up at all. If I do a power reset it will blink a couple times and then never again.
How did you remove the ice making unit from the holder. I can get the left side loose but not the right. Edit: have to remove the 1/4" bolt at the back on the right.
Whirlpool wrv986fdem01 unplugged then plugged back in. Optic light stays on for a few minutes then goes out. I tried test#15 red light comes on 02 code comes up I placed my hand in front of sensor and code goes to 01. It seems the sensor detects empty and full during test mode. No red light when refrigerator is running. Any help is appreciated.
What is wrong if your ice maker is only filling 5 of the seven ice cubes? Tried turning the little plastic side screw one turn..it did nothing!..:/ thx,for any help!
Great video thank you!
If the flap door on the left side of the refrigerator is pressed closed, should the red blinking light on the right side panel quit flashing? If it does not stop flashing, do I need to replace the sensor? Do I need to jump start using the your wire method?
It is a sign that the sensor is not working. First clean the 2 sensors on each side with a q tip and if it still don't work that is where I would start. Replacing the Emitter and reciever.
I decided to replace both components of the IR system. Still cannot get the short cables to plug back in to the new pieces. Any suggestions or pictures?
I have replaced the light emitter and receiver, ice maker and water valve and the ice maker is not cycling. What else can I do?
What do I do if it's making ice but not dispensing out of the door no sound nothing I have this same fridge
Turn adjustment screw clockwise to reduce water fill time.
Turn adjustment screw counter-clockwise to increase water fill time.
I have a Kitchen Aid undercounter ice make model KUIC15NRXS2. It appears the water fills up the bin and will not stop. Would you know what would cause this? Thank you!
What do you do when the red infrared sensor isn't on or blinking?
Did you ever solve your problem with red sensor light?
@@johnjustice8860 Yes I did. I ended up having to purchase a transmitter and receiver board I found on ebay. The red light now powered up but still not producing ice. I ended up discovering the receiver board wasn't working so I installed my old receiver board back in and now everything is fine. I had a hell of a time removing the transmitter board because a transistor had heated up so much that it melted the plastic around it and actually welded itself to the wall of the freezer. All seems to be back to normal now and I am greatly relieved that I don't have to replace the refrigerator. That would have been a major chore as it is in our Class A RV and I would have had to remove a side window to make the exchange. BTW: Happy New Year and be safe and stay healthy. Mike
As always I appreciate you bearded man!
I am more confused after watching this video
lol I know i threw a lot of info at you but just try to wrap your head around it lol
I Jane a freezer like that but it doesn’t make ice can you help me why like that. Thank you I
What is that right angle extension on the drill? That thing is cool.
Is the red light suppose to be blinking?
Man I have an issue with the same ice maker . I replaced the water valve and jumped the ice maker T and H ..the ice maker does cycle and I still get no water..would I need to replace the ice maker cause it probably not sending the command to fill with water..? The water line is not blocked and the inlet valve is brand new and I can get water thru the dispenser.. thanks any help please . 👍👍👍
Sounds like your ice maker to me. I see them fail where they don't send power down to the valve all the time.
@@BeardedApplianceRepair thanks that what I thought , ordered a new one ..👍👍👍
What if you don’t have a sensor light at all?
Great camera work.
I wanted to throw up.
Ok so i press the light switch and the left flapper and the red light turns off, but when i let go of the light top switch the light is steady, when i let go of the left flapper the light blinks. Is it working properly?
Yes that is how it should work.
Who ever edited this video, you have a lomg way to go.
Any suggestions to..I have the exact model and my maker won’t STOP making ice. Even in the OFF position
The will be you emitter and receiver than. Part links will be in the description of the video.
I agre
How do I remove ice maker
That's what is wrong ok water is coming out the freezer compartment and wetting the floor
My ice bin is stuck and cant get it out?
You may need an ice door kit. look at the hole the ice drop down through and look to see if that door is sticking open. That ice build up underneath the bucket is a sign of an air leak from that area.
Where did you get ur drill attachment?
Got mine at Lowes. You should be able to find them at your local hardware store though. If you can't I know you can find them on amazon.
My lord that was confusing. I got nowhere after watching this
It was very difficult to try to watch this video. The camera was all over the place, it wasn’t capturing in full frame what you were doing half the time.
Guess its all in your perspective. I saw it fine. His knowledge helped me diagnose my issue. Part is replaced and its running fine now ..A simple thank you to him would be more appropriate than complaining…
@@shawncosmos5431I think constructive criticism is being mistaken for a complaint here. I also had the same issue. Tried to follow along but it was difficult. I had to go based off what he was saying.
@@TheRachniQueen Fair enough.. Did you get yours running right?
This ice maker is a piece of Shit 💩. Too many things to go bad .
Somebody needs to teach the owner of that fridge how to pack the shelves. They just threw bags of meat on the top shelf near the ice maker?! They might as well have put them above the ice maker while the blood drips down.