This can be a free mod by also taking weight out of each shoe. Cut the ends off or drill some holes and tighten the stock springs. Just make sure they are the same weight with a gram scale. Fluids make a small difference as well. Instead of atf try 0w30ND. It has to be a non detergent.
@@Toxic2T been running chopped 2 shoes for years and never had a problem. Haven’t even bent a post because with less spring tension and lighter shoes helps. Unless you cut them wrong and don’t get the weights exactly the same then this doesn’t have a negative effect
I have multiple tomos mopeds, one I use for wheelies which I have tuned a bit and one for driving to school, what you Said about weight is very true but If you have a bit more power than stock it makes it way easier, but I still run 50cc on my stuntbike and I can still wheelie it like crazy, so it’s not all power people, just practice
@@one_boi3926 I have a fast 50cc cilinder and a 15/15 mm carb (Standard it is 14/12), I also put another exhaust on it for more torque, that’s about it, suspension is all standard, and the front tooth is 26 and rear 22
Practice with a peddlebike to get a feel for the left and right balance , its the same situation with the surron / segway ebikes they are light and its diffrent when compared to a dirt bike
This winter head down to my place in Florida...gf has 1978 Tomas and I sport the 83 puch...pick them ...someone was throwing them out...got them going ...we can do wheelz for days😎
I've made 7000km with a stock bottom end and a 70cc, a 70cc isn't pushing that much to break stuff unless you rectify the head and work on the crankcase, it's safer to go with a stronger crankshaft but haven't had any problems yet so
In a different scenario if the bike is on country roads running wide open for miles, it will have a meltdown. Big side of the con rod will seize (specifically on a puch e50). I wouldn't install a 70cc for a customer without the crank, but for myself I literally did it today. I know the engine will be fine all fall and winter.
I have a moped a tomos and i have a good power because of my 70cc but when i used a 50cc i used to wheelie too because i was sitting more back but now i am sitting a litte bit more foreward it is true your body is the key to wheelies
guess i figured out what the problem with my ciao is haha, ive always has the stock seat on on which you cant really go back to shift your weight. might invest in a bench seat
I have a maxi KL with a similar setup 70cc 19,5 carb and the techno version your exhuast, but I can't get mine adjusted right, what main jet do you use? hope you can help
Please please please keep up with your channel and content bro I was so gutted when you dropped off for a minute I was so happy when a two stroke j notification popped up love you and your videos man think you should do a two stroke supermoto build
Bro I really appreciate this comment. I totally plan on keeping the content up. It was tough for me to balance TH-cam and life for a while but I’m in a better place now to create content. Money is the biggest thing holding me back for new builds but that will come with time. Thank you for sticking with me bro!
I totally understand where your coming from on the life and money front shit just gets to you at times and you’ve had your injuries too but your laugh and energy on your videos is infectious I love your content can’t wait for the next one and I think if you keep it consistent in my opinion you’d be one of the best TH-camrs out there loved the old 125 vids too man all the way from the uk. Much love brother.
On stock seat it is much harder cose you have to stand when you standing the moped on back seed. I have old moped Babetta 210 and it is really fun, but it is hard..
Is it a pitbike style engine (4speed manual or semi-automatic), if it is it accepts most pitbike engines and you can order one from china like 125 lifan, 140,150,160 yinxiang or 155 and 190 zongshen
you think i can do a wheelie on my full stock piaggio ciao that goes 27km/h (bcs of regulations) or not. I can put some better parts on it but it's not going to make the speed any better, just the acceleration i think so i have to rebuild the whole engine bcs of the speed limiter.
3:40 you don't have to make any power, I do wheelie mine with just a tomos seat and rear shocks iirc. Can't lift itself up nor with pulling the bars, but you have legs and use them to help you get the front wheel up+I don't have a rear brake so my feet stay down all the time during wheelies
For my self i like a ciagar exhaust better for wheelies it can realy safe you from looping out and if i was you i would run a 70cc with a reed valve so you will have better throtle respons
@@TwoStrokeJ Knee knocker is at least for me a lot harder, its harder to balance the bike, especially at low speeds… and if you land w the handlebar turned one way, you re done
On 4:57 you say that it doesn’t make te power for you. That is not true if you have the right setup it wil. My setup is 65cc polini 16mm bing High pressure 65cc cilinder head an exhaust like you And yellow clutch springs Al Nice dialled in and set up right It comes just up in the powerband which starts at about 15 mile per hour. (Sorry for bad English) I do not have an camera but maybe in the future so I can show it!
Tbf would totally love to had similar looking moped. What's the model ? Any others looking similar to this one ? Just asking , not sure if i could find one in Europe tho,or afford it😅.
awesome video man! i wanna do wheelies like u because i also do wheelies on a moped. i just love ur videos and would be glad if u would watch one vid of me doing wheelies on my chanel and maybe give me tips!
I think it would be possible if you had the same seat I have or similar, so you can put your weight way back over the rear wheel. I tried with a normal bicycle style seat when my bike was stock and I couldn’t really get it up. But I also had less skill so who knows
okay, thank you for your respond. i am going to try stock. i dont want 70cc, what could i do instead? i was thinking new exhaust, another carbu, change the gearing. anything else?
@@TwoStrokeJ oh okay!! Thanks for letting me know! By the way i have the org seat on mine and i find it complicated to lift the bike up, have any tips?
![[#2024MAMA] ROSÉ (로제), Bruno Mars - APT. | Mnet 241122 방송](http://i.ytimg.com/vi/dgGqD28J6aQ/mqdefault.jpg)
here in the Netherlands (europe) mopeds are like a really big thing in the bikelife scene so its cool to see you rip these things in America
Yea bro! I love it
Klopt inderdaad
Oh sheeeet meer Nederlanders 😂
Ofni pik 125cc zip broer vliegen op mn achterwiel
@@dennishazeleger7414 GEKOLONISEERD
Big Moped Vibes!!!
Summer is for minis
You can put stiffer springs on the clutches so the clutch would grip at higher rpm for better acceleration from standstill
Yea I plan on doing that eventually!
This can be a free mod by also taking weight out of each shoe. Cut the ends off or drill some holes and tighten the stock springs. Just make sure they are the same weight with a gram scale.
Fluids make a small difference as well. Instead of atf try 0w30ND. It has to be a non detergent.
I took my springs out of the clutch because it was not engaging because of compression
@@buttcheeksbuzzard8765 not the best advice tbh. it cuts down reliability by a huge margin
@@Toxic2T been running chopped 2 shoes for years and never had a problem. Haven’t even bent a post because with less spring tension and lighter shoes helps. Unless you cut them wrong and don’t get the weights exactly the same then this doesn’t have a negative effect
thx for this video, gonna use this guide to wheelie my tomos. love from the Netherlands
Awesome man! Good luck with it!
I have multiple tomos mopeds, one I use for wheelies which I have tuned a bit and one for driving to school, what you Said about weight is very true but If you have a bit more power than stock it makes it way easier, but I still run 50cc on my stuntbike and I can still wheelie it like crazy, so it’s not all power people, just practice
Oh yea don’t get me wrong more power helps a ton haha. Just trying to let everyone know you don’t need it
@@TwoStrokeJ yeah exactly, you can wheelie with not alot off power but having some power does help a lot
@@hondapower8462 what modifications have you done to your stunt tomos?
@@one_boi3926 I have a fast 50cc cilinder and a 15/15 mm carb (Standard it is 14/12), I also put another exhaust on it for more torque, that’s about it, suspension is all standard, and the front tooth is 26 and rear 22
Finally THE TUTORIAL! I have a puch maxi myself snd have been wondering how to learn thanks!
Hope it helps bro! Good luck!
Love the moped vids keep it up!
Thank you bro!
Droppin the best content always.
Means a lot bro thanks for the support
At 61, I can't wait to do this. Great video. Thumbs up.
Thanks for the feedback man!
still alive?
@@rpz yup
@@rpz💀💀💀💀
@@rpzbroooo💀💀💀
According to this channel mopeds are better than groms ❤️😂 love the vibe and the style
This is a fact
Two stroke j is back again 😭😭 thank you Jesus!!
Praise da lord!
Its easiest to learn dirtbike wheelies with a derbi senda with power pipe since it has the powerband but its not quite as aggressive so its perfect
Seems legit
Dang I wish I had a moped, this looks sick!
I coulda sworn you…. Never mind
Amazing video!!!
I can't wait till my puch maxi 2 gear is fixed so i can start doing this. It's gonna be lit!!!!
Good luck bro! Thanks!
The Dellorto 19mm is one hell of a carb. Have you tried higher rpm clutch and porting the exhaust? That would be a gamechanger for torque.
Nope, this engine build is super mild. Im gunna do one fully built some day
Practice with a peddlebike to get a feel for the left and right balance , its the same situation with the surron / segway ebikes they are light and its diffrent when compared to a dirt bike
Yea man that’s a good idea pedal bikes are similar
This winter head down to my place in Florida...gf has 1978 Tomas and I sport the 83 puch...pick them ...someone was throwing them out...got them going ...we can do wheelz for days😎
Let’s goooo!
Sick video dude ❤️
Appreciate it man!
i really want to learn how to wheelie on my moped
This video is perfect for you then bro
i have a tomos a3. its exactly the same only that it has two gears and a little more horse power but i still cant get it up
#JWAY yessirrrr
My man BREADSTICK COMING THROUGHH
@@TwoStrokeJ yessir u know i had to
I've made 7000km with a stock bottom end and a 70cc, a 70cc isn't pushing that much to break stuff unless you rectify the head and work on the crankcase, it's safer to go with a stronger crankshaft but haven't had any problems yet so
Same man! And I agree if you run a mild setup it should be good
In a different scenario if the bike is on country roads running wide open for miles, it will have a meltdown. Big side of the con rod will seize (specifically on a puch e50).
I wouldn't install a 70cc for a customer without the crank, but for myself I literally did it today. I know the engine will be fine all fall and winter.
I have a moped a tomos and i have a good power because of my 70cc but when i used a 50cc i used to wheelie too because i was sitting more back but now i am sitting a litte bit more foreward it is true your body is the key to wheelies
Exactly, more power let’s you do more but it still applies
Tomos is a fake Puch
@@KMCDM not at all its right the opposite
guess i figured out what the problem with my ciao is haha, ive always has the stock seat on on which you cant really go back to shift your weight. might invest in a bench seat
I have a maxi KL with a similar setup 70cc 19,5 carb and the techno version your exhuast, but I can't get mine adjusted right, what main jet do you use? hope you can help
I don’t remember, I think 85? It’s whatever came in the carb stock
Can you do a video of how to do tricks on a moped😃 i can wheelie but i cant do tricks
I can barely do tricks so lemme get better first haha
Yessir nice gloves my boy 🤟🏽 #HighSideLife
Thanks bro!
Aye new video. And im early with it
You a quick clicker my man
love the tutorial vids. going to use that advice on my crf50 too
been watchin ur videos for about a year or two now. finally was able to cop my own lil 50cc suzuki i cant wait to start stuntin it
Let’s gooo bro! Good luck!
Awesome.. thx for sharing/teaching.
no problem bro!
Please please please keep up with your channel and content bro I was so gutted when you dropped off for a minute I was so happy when a two stroke j notification popped up love you and your videos man think you should do a two stroke supermoto build
Bro I really appreciate this comment. I totally plan on keeping the content up. It was tough for me to balance TH-cam and life for a while but I’m in a better place now to create content. Money is the biggest thing holding me back for new builds but that will come with time. Thank you for sticking with me bro!
I totally understand where your coming from on the life and money front shit just gets to you at times and you’ve had your injuries too but your laugh and energy on your videos is infectious I love your content can’t wait for the next one and I think if you keep it consistent in my opinion you’d be one of the best TH-camrs out there loved the old 125 vids too man all the way from the uk. Much love brother.
Finally another puch video
Gotta deliver to the moped lovers
Nog een nederlander gevonden! Ik maak ook tomos video’s 👀
@@two_stroke_rider weet ik, ik volg je al tijden op insta en heb je vgm weleens gesproken in je dms hahaha
@@basvanlangerak8423 haha meen je niet! Toevallig weer 😂
@@basvanlangerak8423 dit weekend komt er waarschijnlijk een nieuwe video in een soort “two stroke j” stijl 🤪
Notification gang for the second timeee
Freaking quick draw man, amazing
killing it like always
Thanks my guy
I hope this helps me tanks for the tips!!
Good luck bro!
On stock seat it is much harder cose you have to stand when you standing the moped on back seed. I have old moped Babetta 210 and it is really fun, but it is hard..
Yea man I couldn’t do it with the stock seat that’s why I got the one I have now
I'm struggling to get the my bodyweight perfect, because I don't have a long seat like you. mine is a puch maxi k and have a small seat. got any tips?
i never saw you wheelie the yamaha dt50 you had
It’s the first bike I had, I didn’t know how to wheelie or ride at all when I owned it
So your exhaust pipe give lots of mid range power, what kinda power would some like 717squirrel exhaust on his Puch or maybe a bitubo exhaust give?
That type is gunna be top end power. Top speed will be better with those pipes
I own a Honda c90, what can I do to improve it? It has a 4-stroke engine.
Is it a pitbike style engine (4speed manual or semi-automatic), if it is it accepts most pitbike engines and you can order one from china like 125 lifan, 140,150,160 yinxiang or 155 and 190 zongshen
Just know for a manual pitbike engine you have to get a clutch lever and cable for it
I’ve been trying this on a kromag free spirit and maaan it’s heavier but I think it’s possible 😅
you think i can do a wheelie on my full stock piaggio ciao that goes 27km/h (bcs of regulations) or not. I can put some better parts on it but it's not going to make the speed any better, just the acceleration i think so i have to rebuild the whole engine bcs of the speed limiter.
3:40 you don't have to make any power, I do wheelie mine with just a tomos seat and rear shocks iirc. Can't lift itself up nor with pulling the bars, but you have legs and use them to help you get the front wheel up+I don't have a rear brake so my feet stay down all the time during wheelies
That’s what I’m talking about bro!
Hey man, could you link all the parts you have? Would help heaps with finding the parts 👍🏻
How to do a drag wheelie on a moped with foot brake without looping out?
No clue bro I’ll let you know when I figure it out
What seed are you using love it?😍
Huh???
Love it
🙌
Does this work for all bikes cuz it seems legit
For my self i like a ciagar exhaust better for wheelies it can realy safe you from looping out and if i was you i would run a 70cc with a reed valve so you will have better throtle respons
You gotta ride my tomos it makes plenty of power to power wheelie lol
They all make plenty of power to wheelie just gotta know how to use it
I already know how to whellie, now I started learning knee knocker
That’s dope man! I still suck at them need more seat time for sure
@@TwoStrokeJ Knee knocker is at least for me a lot harder, its harder to balance the bike, especially at low speeds… and if you land w the handlebar turned one way, you re done
Is this moped automatic? How on earth did you bump start it?
where did you buy your saddle?
Been wheeling my tomos with my feet down for the longest time i just can not get my feet up
Is it ok to have a 25ccm moped flexer
Ja ich hab auch eine Tomos
On 4:57 you say that it doesn’t make te power for you. That is not true if you have the right setup it wil.
My setup is
65cc polini
16mm bing
High pressure 65cc cilinder head
an exhaust like you
And yellow clutch springs
Al Nice dialled in and set up right
It comes just up in the powerband which starts at about 15 mile per hour.
(Sorry for bad English)
I do not have an camera but maybe in the future so I can show it!
Yea I know it’s possible, but for most people who ride bigger bikes it still doesn’t feel very powerful haha. That’s what I meant
@@TwoStrokeJ ah okee that’s right🙈
J please put a god damn airfilter on it. a sock and zipties atleast, you will thank yourself in the future😂
NEVER! But I understand haha I probably should but this engine isn’t very fancy anyways haha
Tbf would totally love to had similar looking moped. What's the model ? Any others looking similar to this one ? Just asking , not sure if i could find one in Europe tho,or afford it😅.
1980 Puch maxi!
Puch maxi s e50
Ty man
No problem brotha
What is the name of the background music genre
awesome video man! i wanna do wheelies like u because i also do wheelies on a moped. i just love ur videos and would be glad if u would watch one vid of me doing wheelies on my chanel and maybe give me tips!
Do you Think it’s possible with a totally stock puch maxi?
I think it would be possible if you had the same seat I have or similar, so you can put your weight way back over the rear wheel. I tried with a normal bicycle style seat when my bike was stock and I couldn’t really get it up. But I also had less skill so who knows
okay, thank you for your respond.
i am going to try stock. i dont want 70cc, what could i do instead? i was thinking new exhaust, another carbu, change the gearing. anything else?
lean forward put your weight back thats like a metaphor for life too JWAY
Precisely I think
I have foot brake on my Maxi, is it still possible to Wheelie it?
Absolutely!! I am working on installing a footbrake on mine soon. The same concept applies, just gotta use your foot rather than your hand!
@@TwoStrokeJ oh okay!! Thanks for letting me know! By the way i have the org seat on mine and i find it complicated to lift the bike up, have any tips?
what moped is that cause i would buy one
I say it in the video, it’s a 1980 Puch maxi
I want that bike.
Get one!! They are so fun
@@TwoStrokeJ i have a 1978 peugeot 103. Its on my channel. But i want a puch maxi lol also
What are the pegs you have on the back?
Just for fun stunts and stuff haha
@@TwoStrokeJ haha i got that😅 but i ment where to buy/what they called i want them to but dont know wat will fit my moped
I cant wheelie my bike bc my exhaust is to long
You got too much air than fuel you need an air filter or to adjuste it
Going to be lots of dropped bikes in the next few days lol.
Nahhhh everyone will be a pro hahaha
What gearing are you using?
Stock bro
@@TwoStrokeJ get counting those teeth 😝 stock gearing differs
What’s the max rpm with that pipe?
Not sure, I don’t have a rpm gauge
"This is the only thing I have done with engine" changes everything but the frame... oh... never mind
lmao
My friends puch maxi does 0-30 kph In 1 min so there is No way
Yes way!
Your bike is very badly tuned for a 70 cc. My 70cc takes off way faster. Its a scooter, but i dont think that makes much of a difference.
Well that’s all clutch tuning and mine is completely stock. I need to adjust some stuff to allow it to rev higher and take off faster
It’s called a poooosh
I never know bruh haha