Good day ,mines is showing fully charged when the charger is plugged in ,but if you turn it on and press the pads the light indicator shows red and it makes a beeping noise
Sounds like the battery pack has had it. It’s not uncommon for one or more of the cells that make up the pack to fail then giving a false charged indication. Was it stored away not fully charged? A replacement battery pack should solve this
As far as I know the battery on mine is not a problem. My problem is that the charger doesn’t charge it. When I plug it in it the charging light isn’t on the plug or hoverboard. The charger is fine it produces the voltage. So how can I fix the hoverboard. The port itself is good too and provides voltage to the first board it plugs into but I am not sure about the connection to the rest of the board.never mind figured it out
The battery gets to dead and charger won’t read. Take a drill battery and run a jumper wire + To + and -to- then plug the charger in and disconnect the drill battery. All good after.
Take note of the + and - and desolder. Option 1. When you get the replacement battery pack you can cut the plug off the wires and solder the + and - in the correct order to the board. Option 2. You may need to purchase xt60 or xt90 plugs for attaching to the wiring for the battery pack and the board. Hope this helps.
The model name is not important. It’s the shape of the battery pack to fit into place. That shape is generally the same voltage that you would require for a hoverboard and the more mAh the longer the run time
I have a hoverboard, charger works, charging port work. When i plug port into board the right wheel seems to rock back and forth ever so slightly and it doesn’t charge. Any ideas?
Disconnect the battery pack and if you have a multimeter identify + and - on the xt connector and + and - on the charger plug. If battery pack voltage is low then you can charge it directly adapting a couple of pieces of wire. The charger light will let you know when it’s fully charged. Reconnect and if it still doesn’t work then there may be a problem with the main board
what is the type of connector to use on the hoverboard cables please? I would like to repair a broken cable without having to buy a card to have the cable. Thanks a lot
I have two batteries like this. I took out the battery, removed the sleeve and checked each cell voltage on the connector that plugs into the BMS. Most cells were very low voltage at around 1-2v. I charged each cell without the BMS plugged in and made sure each one went to 4.2v. Reseal the battery pack and then try again. My batteries charged for a short while with a red light on the charger and then the light went green.
Good day ,mines is showing fully charged when the charger is plugged in ,but if you turn it on and press the pads the light indicator shows red and it makes a beeping noise
Same with my Neice’s
Same with mine
Same with both mines
Same problem if someone find the solution the solution plz help
Sounds like the battery pack has had it.
It’s not uncommon for one or more of the cells that make up the pack to fail then giving a false charged indication.
Was it stored away not fully charged?
A replacement battery pack should solve this
This video helps me a lot. Thank you very much
Great work thank you
As far as I know the battery on mine is not a problem. My problem is that the charger doesn’t charge it. When I plug it in it the charging light isn’t on the plug or hoverboard. The charger is fine it produces the voltage. So how can I fix the hoverboard. The port itself is good too and provides voltage to the first board it plugs into but I am not sure about the connection to the rest of the board.never mind figured it out
Same
What was issue?
I think that I found why is that is because mother board died and is need to be replaced
The battery gets to dead and charger won’t read. Take a drill battery and run a jumper wire + To + and -to- then plug the charger in and disconnect the drill battery. All good after.
Great, exactly what I was looking for🎉
Does anyone know how much a new battery pack is likely to cost? Thank you
Online generally less than $€£40 and at a shop/store/retailer it would be more
What should I do if my battery is directly saudered to the board?
Take note of the + and - and desolder.
Option 1. When you get the replacement battery pack you can cut the plug off the wires and solder the + and - in the correct order to the board.
Option 2. You may need to purchase xt60 or xt90 plugs for attaching to the wiring for the battery pack and the board.
Hope this helps.
Hi Paul ,
have you made a video that show how you charged the batteries ?
I already changed the battery it’s flashing yellow still i recalibrated it already
I tried getting a new battery pack but I can't seems to find my exact battery. Can I use another model?
The model name is not important. It’s the shape of the battery pack to fit into place. That shape is generally the same voltage that you would require for a hoverboard and the more mAh the longer the run time
Hello i am new to this channel pls help me when i plug to charge my hoverboard its red and it can not be charge pls help me
I have a hoverboard, charger works, charging port work. When i plug port into board the right wheel seems to rock back and forth ever so slightly and it doesn’t charge. Any ideas?
Disconnect the battery pack and if you have a multimeter identify + and - on the xt connector and + and - on the charger plug. If battery pack voltage is low then you can charge it directly adapting a couple of pieces of wire. The charger light will let you know when it’s fully charged. Reconnect and if it still doesn’t work then there may be a problem with the main board
My battery has 35 volts but the it will not turn on without the charger plugged in
Same
Did you find the issue?
Dear frend I need link for purchase double system driver card please help
Thanks
what is the type of connector to use on the hoverboard cables please? I would like to repair a broken cable without having to buy a card to have the cable. Thanks a lot
I can't take apart my hoverboard
I cannot fix it bc it is. Hard casting
😢😢😢😢😢😢😢😢😢😢😢 sorry I don’t have that battery
mine when i plug it in, the green light just turns off, what that mean??
It means you have a short some where
I have two batteries like this. I took out the battery, removed the sleeve and checked each cell voltage on the connector that plugs into the BMS. Most cells were very low voltage at around 1-2v. I charged each cell without the BMS plugged in and made sure each one went to 4.2v. Reseal the battery pack and then try again. My batteries charged for a short while with a red light on the charger and then the light went green.