Just buy-it and I figured was something wrong with charging... so I look on you tube and I found your video. My boy is happy now for his birthday.Thanks man. The battery was different but I sorted how to fix-it. You’re the man.
Could have explained that you were connecting the negative to the spot marked B- on the board, for those that have a different one, but thanks a million, saved my step daughters hover board! Or at least saved me $60+ buying another battery.
Mine is different too and I tried charging in several pads but didnt keep it very long in each pad. Is there any issue if I kept that in each pad for too long? My battery wasnt charged for many months and might have lost the voltage completely. Any tip will be helpful.
I know it's been 4 years but I recently just got this issue with my hoverboard and after watching several videos your video was the most helpful and simple way to fix👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽 thank you after jumping it its now charging 😁✌🏽👍🏽
Best video on battery advice on the hole of TH-cam, I have not be able to charge my battery and have been up the fucking wall because I paid good money for these batteries, you have just fixed my problem in 5 minutes, thankyou very much you cleaver man , jfk over and out
Thankyou for taking the time, after 3 months of no use my 'zinc smart gt' only has lights on the board if i have charger plugged in, it will recalibrate but still no movement in board, i take ''green light' charger out and everything dead again, no lights no beeps. So hopefully i can kick start the battery from inside or verify that its dead forever. I have multimeter but have never used one. Now i will open board up & try. My boy would be so happy. .... EDIT.....My battery pack is different, is he putting one wire on negative and other end to a positive? or neg to neg? wire sparks and heats up but no change, BATTERY reading at 12, charger still green light. Charger isn't faulty.
My battery wouldn't charge because it was just a litter undervoltage. Battery light red and only beeping. But here is a tip: when you remove the gyro cable (next to the led cable) on one side the battery charges. When it gets to 36v then the gyro cable can be attached again. That only works if no cell has failed, but you can try it (just be around the first charges, in case anything goes wrong).
Good stuff, my battery was at 6 volts and wouldn't charge, had to short it out a few times but it finally started charging. It's now at 25 volts and climbing. Thanks
@@MrJOLLYRANCHER92 I completely disassembled all the battery, wiring all, kept photos how qnd where all connected and a layout, salvaged few dead ones and replaced a few, and soldered all back together with copper wire, Taped the whole thing, still works to this day, I know its a lot of work but it was worth it for me
My brand new hoverboard run time is around 25 minutes then it cut off power of board. At full charge it was around 41.5 V and after 25 minutes the battery voltage was only 37.8 V for cut off. Why is the voltage still so high and already there was a cut off the power? At wat voltage should the board switch off? Any suggestions?
Good this works, thanks for the information, I changed two of the batteries because they had corroded but still wouldn't charge all problems solved now and link removed.
you are a life saver. I think I ended up shorting several different spots on my board before it worked, but in the end... IT worked!!! Thank you So much!! Dunno if you still make videos or not, but you got a subscribe from me for saving me $100. Thanks again!
Hi, My battery is showing 41.2v but hoverboard still won't work. Does that mean the BMS is at fault? Is there a way to fix the bms or do I have to buy a battery? thanks
Just as I was getting annoyed that this was not working for me, and just kept seeing sparks which was a bit concerning. After 4th attempt the red light on my charger appeared solid after flashing for around 10 seconds. Once the charger light turned green, I checked with a multimeter and battery only outputs 25volts, should be 36-40?? Hoverboard still not powering up. 😕
Very well..... But I'm little bit confused ... After that if battery consumed and low warning show than we have to do that same work again or we have to do it once??? Please tell me
With charger plugged in mine lights up when I press power button without the battery. My battery is slightly different from yours. I get 18 amps from charger board.
I have same problem and I tried your solotion. Battery is charging only if I hold the short connection permanently. Do I have to pemanently solder the short connection or is there another way around? Is there any problem or danger with soldering the short connection?
Permanently soldering the connection between "P-" and "B-" would be extremely dangerous. As I understand it, when you short the 2 terminals, you are essentially bypassing the protection circuit and sending power to the batteries directly. The protection circuit is what is keeping your battery packs from overcharging and bursting into flames. It would not be wise to bypass it for more than a few seconds.
Unfortunately, this may not even if it charges at first. Mine fully charged then the battery died again. After trying to charge it again, even with shorting the connection, it won't turn red & charge, unless I hold it there 😕
My battery is different. But when i try this method i just big sparks. Its a different layout. Have you got social media i can contact you and forward a picture
Bro i don’t have the voltmeter? Is it that i have tk connect the wire with voltmeter and then with the black wire or we just have to get a wire and connect it with the black wire? Plz reply i’m rly confused
my battery is 36v and its charging so fast and its running out of battery so fast too. i tested my battery voltage and its 38v whats the problem? is it the charger?the brushed controller?or the throttle?(its an electric scooter not a hoverboard)
I have no idea why this works. I am not very "electrical" but I took my battery apart and took a wire and connected it like he said....and it worked. I don't know how long it will work, but my battery is charging now, and it wasn't before.
What should i do my board i switch on charge e board during charge is flashing amber and power is indicate red light but within 3hr power indicate light turn green but board still amber flash for about 2~3hrs... auto shut down. After i plug out switch 🔛 everything connect well on green light but when I wanna ride another side flash red with peep sounds i try it few times but charge within 3hrs done yet after 1st time charge i can't even used already
I try, but it did not work , but when I was holding the short wire there the it wil charge but it goes to green light on the charger after 30 secound. Then I turn it on it blacks oout after 2 min
What he’s doing will only work for a very short time and the battery will go dead very fast instead you need to take another battery and use it to jump your Hoverboard battery so take another battery and from the spare battery positive connection to the positive connection on your Hoverboard battery and then from the spare negative connection to the negative connection on the Hoverboard battery Take any wire from old electrical cord cable just make sure it’s insulated or you’re wearing like rubber gloves. So two separate cables with the copper exposed on each end, kinda like mini jumper cables but without the clamps. don’t use a small cable like for a phone charger, copper wire should be at least sinilar thickness as if you combined about 3 toothpicks together. Then make the connections positive to positive negative to negative from battery to battery. Do it until it shows it’s charging, red light on the charger stays on until fully charged just like it originally would. A good spare battery to use for jumping would be like any batteries used for power tools or a scooter battery would work, if you have long/thick enough cables you could use a car battery. 18650 Lithium ion batteries the completely flat side is negative the raised end is positive. Power tool battery you can just touch wire to the metal positive/negative charging connections they should be marked +/- If you cant figure out how to access positive/negative on the hoverboard battery then I wouldn’t suggest doing this without someone walking you through it.
![ลองสุ่มไอโฟน 990 โกงมั้ย? [ โกงมั้ยครับ ep.101 ] | DOM](http://i.ytimg.com/vi/bfsWe0j492k/mqdefault.jpg)
Just buy-it and I figured was something wrong with charging... so I look on you tube and I found your video. My boy is happy now for his birthday.Thanks man. The battery was different but I sorted how to fix-it. You’re the man.
Can you please say me how u short circuit ed it, bcoz mine is different too. Its says -B and -P. I'm confused 😕
Would have never thought of it.....when I excited the battery........STARTED CHARGING...THANK YOU SIR!!!!
لم اعرف الحل هل بإمكانك الشرح لي
You are a legend. Short circuiting the battery worked a treat. Was just about to give up on it. Cheers
I don't know if i was searching correctly but after 3 long months I finally found the fix for the same issue here on your video. Thank you very much.
Same
It work after even 2 years of not using it thanks a lot buddy !
You re amazing!
I wonder what label name on pad at the opposite side ? B- or B+ or …?
Could have explained that you were connecting the negative to the spot marked B- on the board, for those that have a different one, but thanks a million, saved my step daughters hover board! Or at least saved me $60+ buying another battery.
I did this and my battery is now gone forever
@@jacobr5465 Had a different problem, or you did it backwards.
@@jacobr5465 sounds like you shorted the wrong pins
@@realracerx my battery is different so I don't know which one to jump
DUDE!!!! thank you!!!! mine looked little different but i short circuited the black wire with other pads and now its charging!!! cheers brother
Mine is different too and I tried charging in several pads but didnt keep it very long in each pad. Is there any issue if I kept that in each pad for too long? My battery wasnt charged for many months and might have lost the voltage completely. Any tip will be helpful.
نفس المشكلة لاكنني لم اعرف الحل هل بإمكاك الشرح لي ؟؟
Save Money and Don't Keep Buying Battery. This was a Excellent Video... Thank You. Best Hoverboard Charging Problem Video on TH-cam!!!!!
I wonder what label name on pad at the opposite side ? B- or B+ or …?
I know it's been 4 years but I recently just got this issue with my hoverboard and after watching several videos your video was the most helpful and simple way to fix👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽 thank you after jumping it its now charging 😁✌🏽👍🏽
Best video on battery advice on the hole of TH-cam, I have not be able to charge my battery and have been up the fucking wall because I paid good money for these batteries, you have just fixed my problem in 5 minutes, thankyou very much you cleaver man , jfk over and out
Had exactly the same problem. Same battery. Fixed it as shown in your video. Thank you.
Thankyou for taking the time, after 3 months of no use my 'zinc smart gt' only has lights on the board if i have charger plugged in, it will recalibrate but still no movement in board, i take ''green light' charger out and everything dead again, no lights no beeps. So hopefully i can kick start the battery from inside or verify that its dead forever. I have multimeter but have never used one. Now i will open board up & try. My boy would be so happy. ....
EDIT.....My battery pack is different, is he putting one wire on negative and other end to a positive? or neg to neg? wire sparks and heats up but no change, BATTERY reading at 12, charger still green light. Charger isn't faulty.
You're genius, I have 10 units new never been used but all of them have this problem, your trick worked in all of them thanks man
my battery is diferent but i i looked for the place where are almost 10 volts (two big black wires) and... IT WORKS!!!! thanks a lot
You ran current from black wire to black wire
@@jessicasanders9610 LOOOOOL
THIS WORKS!! For anybody that does not understand tell me and I will help you!
Please help mee
Mines the same as on the video but when i do as said on the video it still doesn’t charge
Thank you my friend.
My battery is different inside and on voltage. My cable sparked some few times but after many tries it worked.
Hi F R...am sure my battery is jst like yours how did you proceed ?
Me too, have same case w/ u n after tries 3 time it worked again
Did you have the battery plugged into the hover board whilst carrying out the procedure?
I wonder what label name at the opposite side ? B- or B+ or …?
My battery wouldn't charge because it was just a litter undervoltage. Battery light red and only beeping. But here is a tip: when you remove the gyro cable (next to the led cable) on one side the battery charges. When it gets to 36v then the gyro cable can be attached again. That only works if no cell has failed, but you can try it (just be around the first charges, in case anything goes wrong).
It worked for me! Faulty BMS! Thank you
I wonder what label name on pad at the opposite side ? B- or B+ or …?
Thank you this really worked my son is really happy now
I wonder what label name on pad at the opposite side ? B- or B+ or …?
My battery is different, but work's.
Thank you!😱
Great explain....
Thank you very much
Cheers from Denmark 🇩🇰
Good stuff, my battery was at 6 volts and wouldn't charge, had to short it out a few times but it finally started charging. It's now at 25 volts and climbing. Thanks
Ik its been a year, I have a different type batter circuit, idk what pads to short, should I be worried shorting the wrong wires while charging?
@@itzmrdub4591 how did you make out?
@@MrJOLLYRANCHER92 I completely disassembled all the battery, wiring all, kept photos how qnd where all connected and a layout, salvaged few dead ones and replaced a few, and soldered all back together with copper wire, Taped the whole thing, still works to this day, I know its a lot of work but it was worth it for me
I charged the cells individually so it had enough for the board to pick up and self charge
My brand new hoverboard run time is around 25 minutes then it cut off power of board. At full charge it was around 41.5 V and after 25 minutes the battery voltage was only 37.8 V for cut off. Why is the voltage still so high and already there was a cut off the power?
At wat voltage should the board switch off? Any suggestions?
Good this works, thanks for the information, I changed two of the batteries because they had corroded but still wouldn't charge all problems solved now and link removed.
Thank you, this worked good so my son & I are pleased. Thanks again 👍🏻
i guess Im kinda off topic but do anybody know of a good website to stream new movies online ?
Thanks, I signed up and it seems to work :) I appreciate it!
I wonder what label name at the opposite side ? B- or B+ or …?
Very good video!!!
You explain in details a simple trouble.
Many thanks!
Great, you are a Genius!! Many thx man!!
Damn this really worked. Started charging again. Thanks.
What model is urs Samsung??
Never mind. Son used it for 1 week. Then caught on fire. SERIOUS. Do not charge in house. Repeat. Do not charge in your house.
Ohh Sugar! Has anyone else had this happen ?
I wonder what label name on pad at the opposite side ? B- or B+ or …?
I wonder what label name on pad at the opposite side ? B- or B+ or …?
Thanks man, this helped me, it's working
you are a life saver. I think I ended up shorting several different spots on my board before it worked, but in the end... IT worked!!! Thank you So much!! Dunno if you still make videos or not, but you got a subscribe from me for saving me $100. Thanks again!
I wonder what label name on pad at the opposite side ? B- or B+ or …?
Hi, My battery is showing 41.2v but hoverboard still won't work. Does that mean the BMS is at fault? Is there a way to fix the bms or do I have to buy a battery? thanks
Just as I was getting annoyed that this was not working for me, and just kept seeing sparks which was a bit concerning. After 4th attempt the red light on my charger appeared solid after flashing for around 10 seconds. Once the charger light turned green, I checked with a multimeter and battery only outputs 25volts, should be 36-40?? Hoverboard still not powering up. 😕
Can this work without a voltmeter ??
Very well..... But I'm little bit confused ... After that if battery consumed and low warning show than we have to do that same work again or we have to do it once??? Please tell me
Yeh reply man is this a one time fix.
With charger plugged in mine lights up when I press power button without the battery. My battery is slightly different from yours. I get 18 amps from charger board.
I have same problem and I tried your solotion. Battery is charging only if I hold the short connection permanently. Do I have to pemanently solder the short connection or is there another way around? Is there any problem or danger with soldering the short connection?
Pareil pour moi ça ne charge que si je laisse le fil dès que je le retire le voyant du chargeur repasse au vert 😐
Y a t-il en danger en laissant le connexion permanente?
Please have you hild the short connection permanently?
Permanently soldering the connection between "P-" and "B-" would be extremely dangerous.
As I understand it, when you short the 2 terminals, you are essentially bypassing the protection circuit and sending power to the batteries directly.
The protection circuit is what is keeping your battery packs from overcharging and bursting into flames. It would not be wise to bypass it for more than a few seconds.
thank you i fix my daughter hover 1 👍👍👍
What cable can I use to short it? Would a cut phone cable work?
Can i know the indicated power does Singapore sell as i might want learn your style fix my problem
Worked 100%!!! Thank you!
I wonder what label name at the opposite side ? B- or B+ or …?
Excellent hack, worked for me, thanks!
Unfortunately, this may not even if it charges at first. Mine fully charged then the battery died again. After trying to charge it again, even with shorting the connection, it won't turn red & charge, unless I hold it there 😕
My battery is different. But when i try this method i just big sparks. Its a different layout. Have you got social media i can contact you and forward a picture
I wonder what label name at the opposite side ? B- or B+ or …?
Just wanted to say thanks it worked
mine is 4.5 volts or so. Is it worth the try?
Thanks mate, fixed mine with the same fault.
كيف لم افهم شرحه
I did what you said now the charger is blinking red and sometimes green means there’s a loose connection or wired wrong what do I do now?
can't believe it worked!! thanks master
100% works. Thank you buddy, i love you!!!
thanks, subscribe me and share ;)
deiviskns Of course, peace and love again.😚
Muito bom ,sou brasileiro e através de sua colaboração resolvi o problema do brinquedo da minha filha ,ela está muito feliz obrigado amigo.
Bro i don’t have the voltmeter? Is it that i have tk connect the wire with voltmeter and then with the black wire or we just have to get a wire and connect it with the black wire? Plz reply i’m rly confused
Thanks for your video but can you put English Closed Captions please?
this only work if your B- and P+ shows 24V or more. Under 24V, it won't work as the cells are fully discharged.
How big is one cell in an ampere, and can I double the number equal to 10 ampere?
Nice one and thanks.. Had a different setup but just shorted out the 2 negatives and off she went! 👌👍
How you know which ones are the two negatives
What if the 36v battery at 1.34v can that be revived
Very good thank you.
Thank you so much for saving my battery!
I wonder what label name at the opposite side ? B- or B+ or …?
Mate. You are a legend !!!
👏👏👏👏👏👏
Thank you
my battery is 36v and its charging so fast and its running out of battery so fast too. i tested my battery voltage and its 38v whats the problem? is it the charger?the brushed controller?or the throttle?(its an electric scooter not a hoverboard)
I have no idea why this works. I am not very "electrical" but I took my battery apart and took a wire and connected it like he said....and it worked. I don't know how long it will work, but my battery is charging now, and it wasn't before.
still working? no fire no explosion?
Thank you. Helps a lot.
Thanks for the big help .... nice video
My friend you are an absolute legend well done on this fix 🙂🖖👍
How you know which one is the negatives
Can this work with a razor and a segway minilite?
Thank you so much for helping me
Thank you so much.......it worked..!!!👍🏻
Thank you, your video helped me a lot man.👌👌👌
I wonder what label name at the opposite side ? B- or B+ or …?
Nu, berods padėjo, Ačiū. (looks like working, Thanks)
Prasom
Thank bro my battery also working thanks alot
What should i do my board i switch on charge e board during charge is flashing amber and power is indicate red light but within 3hr power indicate light turn green but board still amber flash for about 2~3hrs... auto shut down. After i plug out switch 🔛 everything connect well on green light but when I wanna ride another side flash red with peep sounds i try it few times but charge within 3hrs done yet after 1st time charge i can't even used already
I didn’t work for me my battery is different but i tried your technique and it started to yellow lightning pls help me out
Thankss!!My battery is different but you help me a looot!!!
my battery only shows o.4 volts; Can it somehow be saved?
Thanks, i did like in the video and it started charging.
No problems more videos in 2 weeks
I luv dis guy it works man thank u I don't know how to thank u man
thanks ;)
@@deivisknsYou only reply to positive feedback but ignore the questions, not kind.
God bless you bro
Does anyone know if this totally fixes the issue, or will it stop charging in some time again
No, it'll stop charging unfortunately
Acabei de fazer seu procedimento e deu tudo certo muito obrigado
Thank you very much brother
I get an orange light but goes straight back to green once the wire is off
hello thank you very much for uploading information i need a summary of your solution in spanish por favor ya que no hablo inglés.
Necesitaa ayuda?
Do you know why that is?... its a shortcut protector for prefend a fire by a shortcut...
@deiviskn When I make connection it shows red, but when I let go it goes green again, can i fix the link ?
I try, but it did not work , but when I was holding the short wire there the it wil charge but it goes to green light on the charger after 30 secound. Then I turn it on it blacks oout after 2 min
Where can I get that red cable???
Hope someone can help me answering 🙌
still need?
@@leqsochokheli yes , i want to repair my hoverboard and I have all the stuff but the red cable still need
What he’s doing will only work for a very short time and the battery will go dead very fast instead you need to take another battery and use it to jump your Hoverboard battery so take another battery and from the spare battery positive connection to the positive connection on your Hoverboard battery and then from the spare negative connection to the negative connection on the Hoverboard battery Take any wire from old electrical cord cable just make sure it’s insulated or you’re wearing like rubber gloves. So two separate cables with the copper exposed on each end, kinda like mini jumper cables but without the clamps. don’t use a small cable like for a phone charger, copper wire should be at least sinilar thickness as if you combined about 3 toothpicks together. Then make the connections positive to positive negative to negative from battery to battery. Do it until it shows it’s charging, red light on the charger stays on until fully charged just like it originally would. A good spare battery to use for jumping would be like any batteries used for power tools or a scooter battery would work, if you have long/thick enough cables you could use a car battery. 18650 Lithium ion batteries the completely flat side is negative the raised end is positive. Power tool battery you can just touch wire to the metal positive/negative charging connections they should be marked +/- If you cant figure out how to access positive/negative on the hoverboard battery then I wouldn’t suggest doing this without someone walking you through it.
i have different bms, any help?
how did u get that many hoverboards
The best, thanks!!!!!!
Great video. Good information! Thank you!
It works really well!!! Thanks
Hello sir it works but 10 to 15 mints it will stop charging and again light yellow
Many thanks, worked brilliantly!!!
I wonder what label name at the opposite side ? B- or B+ or …?
thank you so much.my charger is warm and the light is red. waiting for full charge.
Very good
Thank you very much
Deu certo aqui no Brasil, Thanks!!!!!!