Albert my brother, Quad, new radio, Interstellar, Leaf, tennis. How much more cool can you pack in a video? I don't even have a complete quad yet. I almost ordered a build just like your Martian ii build, but have chosen a little different parts here and there. Between you Joshua Bardwell, and Darke Peake, I feel like I have a great start on the whats and hows. Thanks! PS I tend to watch your videos at 1.5-2x speed and the piano piece sounds amazing at 1.5.
SBUS and iBUS are both serial UART protocols... One major difference is that SBUS is an inverted signal while iBUS is not. Otherwise fairly similar and both are much faster than PPM.
Hi Albert, for some reason I'm having trouble getting this radio to work with both my tarot130 and my TBS Powercube. Have you heard of this happening to anyone or have encountered this yourself?
Can not get an arm switch to show in beta flight, not sure what I’m doing wrong I followed along with your video, but still won’t arm, everything else works pid, all other settings are good, but won’t light up an arm switch in modes on beta flight, I think it might be a mapping issue but I’ve tried to rename channels, still know luck. Any friendly advice would be greatly appreciated. Thanks for all the great videos.
It's not that complicated. As explained in the video, you set a channel to a switch and it should show up in Betaflight configurator. If that isn't working for you, I don't know what the problem would be unless I had all the equipment in front of me to diagnose it.
Price is a bit high for a joypad style Flysky compatible transmitter , range is more important to me, ill see if i can grab a review sample as its not worth throwing money at something that falters.
ok i have followed you as far as i can but when i go to the receiver tab nothing moves at all, i have it set to serial base and then to ibus and i have the same on the receiver set to the same as yours in not on a URAT 1,2 or 3 this is the wizzard and its on a IO1, how and why, please help
Hello. I have a problem with failsafe. Done everything like you did,but nothing happens when turning off Evo tx. I looked in betaflight receiver tab and after i turn off Evo tx ,the values just stays in last position.I have failsafe stage 2 enabled. Any ideas? Thanks in advance
Hey guys, I'm new to drones and I can't get FC to recognize my stick movements. Betaflight 3.1 is set to RX/SBUS and turnigy controller set to PWM/SBUS. Controller seems to bind to the drone, but not getting any power to motors. Betaflight does not recognize my stick movrment. pls help!!!
Ah, I don't know anything about how to setup pixhawk, sorry. If you watched the other video, just setup one of the channels on any of the switches and you have to configure that channel for arming in the pixhawk. I just don't know how to do that for that FC.
This was a good video. Could you make a video on how to install this RX to your FC. I currently have s spektum radio that I'm get rid of for this new evolution it would be very helpful to have step by step video. Thanks for your help
There are hundreds of different FC's out there. So you would need to know where your connection to a UART is on your particular board. All you have to do is connect the signal (SBUS) pin to the RX of that UART port. Then connect 5V and GND anywhere on your FC, the source of the power doesn't matter.
hi albert i wonder if you can me!! im going sell my frsky taranis and ive just order a turnigy evolution but my shuriken 250 is set up for my taranis which is the best receiver and is there any videos how to do it!! Tink UK
Are you asking which is the best receiver for the Shuriken 250? It already comes with the XSR receiver built-in... are you asking what Flysky receiver to replace it with?
Albert, Great video! Considering switching from Taranis to Evolution. Should I get the FS-A8S to solder inside my QX90 F3 Board or should I just get the Banggood iRange 6CH Flysky Receiver? pros/cons? Also, isn't having no trim buttons make flying a complete pain? Say I'm flying my QX90 inside with horizon/auto level mode and it's drifting. I would think trimming on the touch screen while controlling sticks would be disastrous or almost impossible. Currently I have to trim almost every time I fly the QX90. The no trim buttons seems terrible, can you correct my thinking on why it's not?
If the iRangeX Flysky receiver is the one I tested earlier and had failsafe crashes, I would not get that one. If there's another one out there, then I have no experience with it so can't say if it's good or not. I have about 10 of the A8S receivers and so far all are working OK for me. However, be aware some people are having issues with that receiver so there might be some bugs to be worked out. YMMV. I don't use the trim buttons on my Taranis and don't need them. Most people probably should not use them in my opinion. It's fine for airplanes but not useful for multirotors with a flight controller. I recommend trimming the flight controller using Cleanflight stick commands instead. Search google for this, you'll see a lot of tutorials on it. This is the only way I will trim and also set level point on the accelerometer and the gyro. Once you do this, you'll find the quad won't drift anymore. Using these proper techniques the trim buttons have no purpose for multirotors and I for one am glad they are getting rid of that kind of airplane stuff that's not needed for multirotors.
One more question on the trims. Do you think the sub-trim feature could allow the evolution to be used as a decent fixed wing flyer? Assuming you can take 1 or two flights to dial in sub-trims and then have a straight flying craft. Is it naive to think this is possible?
thanks for the video. I have question. I followed your steps for setting up failsafe but it doesn't seem to work. when I turn off the tx the motors continue to spin. is there something else that's not covered in your video? thanks again!
Albert Kim I found the problem. I'm using an f303 XRacer v2.1 flight controller running BetaFlight 3.01 and to fix the issue I had to use sbus instead of ibus. Strange but now failsafe works!! thanks again for all you efforts! cheers
Hi Could you please advise, Have changed back and forth from sbus to ibus and output from ppm to pwm ,still cant get the stick movement on betaflight all the switches respond. What am i missing. Thanks
Wow, could be so many things. I don't even know where to start. Perhaps the most likely case is that you are connecting the signal from the receiver to an inverted pad on the FC. You might want to try a different UART and pad that will be uninverted.
@@AlbertKimTV I will let you know, its strange as I say , all switches work , and you can see movement on the tx when the sticks move, the slides on channels move but not on \Betaflight
There's some more information needed here. What kind of flight controller? What kind of receiver? Did you check that it is actually bound? Did you try IBUS instead of SBUS? Usually IBUS works better. Is your flight controller configured properly for serial receivers and you have the correct protocol selected?
I have some videos on my channel... here are a couple to get you started. th-cam.com/video/81cqZanWa3Y/w-d-xo.html th-cam.com/video/iLsSUNhTTnQ/w-d-xo.html
They are basically the same type of signal, just SBUS is inverted... inverted means that in a normal signal like iBUS, when the signal is low, SBUS is high (the opposite or inverted). That's the best way I can explain it. Beyond that, it's technical stuff I don't know about or care to know about. You would use one or the other depending on what equipment you had and that would determine what is "best" or most appropriate to use. For FlySky receivers I recommend using iBUS since it's the native protocol on that receiver. You can also use it on flight controllers that don't support inverting the signal on UART like the old Naze32 F1 boards. The newer F3 board support signal inversion in hardware.
Albert Kim so say I use a kakute f3 flight controller with the turnigy evolution then ibus should be fine? Also if I fly with other people that are using sbus, will ibus interfere with them?
Hi Albert, I just setup this radio last night and Im gettinh some nasty midstick jitter on all 4 channels. Wondering if I did something wrong. And btw 1520 is like futaba midstick, I left it as is.
Don't use SBUS, use IBUS instead. No jitter and no need to adjust center and end points. I will have a video about this in the near future. I just discovered this.
Fantastic, answered lots of my questions. Is the S-BUS inverted like FrSky receivers? I'm connecting to naze32 rev5, which I don't think accepts inverted sbus, so I'm hoping not. And I'm really curious to see how often you reach for your taranis instead. Obviously in a different league, but how often are those extra features worth there weight?
Albert, Can you tell if the TGY i6s firmware update will work on the Evolution as well? I would really like to see an extended menu with rates and throttle curve features like on my Flysky i6. Thanks
Actually it does not. I tried to connect it and the updater doesn't recognize it. We'll have to wait for Hobbyking to bring out the updater. FYI, if you're a multirotor pilot, I recommend you adjust rates and throttle curve in the flight controller. If you're trying to use this with a fixed wing plane, this radio is not designed for that and I don't even think they will include any fixed wing features in a future firmware update.
Albert Kim I am using it for multirotor models,and I have heard the arguments of adjusting rates, etc through the FC software. But I like to be able to adjust things out in the field as i get used to a new model. It surprises me that the firmware isn't recognized, since the TGY i6s otherwise seems so similar
i can't get the télémetry to work, i have connected the main bat to b-det and set the rx voltage but still show low voltage on fully charge lipo. thanks
hi albert , the failsafe on my turnigy evolution /i6C dont work , any ideas? i have set all ok , fail safe set to drop , Ibus working but my fail safe dont work (with previous fylsky receivers fail safe work ok)
very informative video XD the flight footage looks really good on the mobius you had... which one is it and which settings do you use? (on mSetup.exe) i bought one and the video quality seems bad...
I think it was set to cloudy but I don't like that. Check that you have the latest version of the firmware. I think I also turned saturation down a little.
You need a receiver that can do the Flysky 2A protocol. More recent models can use this. For example the Eachine Aurora 90 with the Flysky receiver can fly with this - goo.gl/l4KJwt
h I see. yea i'm new at this and it got confusing with all the different controller and receivers. I got the Evolution and just ordered a couple Flysky FS-A8S for inductrix blade I have and the Eachine Turbine QX70. I think I can get it to fit in the qx70 but don't know about the blade. can't find the aurora 90 anywhere that is not on back order LOL just my luck. thanks for the help. love your channel !
The one that comes with it. It has also worked with the taranis on this FC. I have even turned on Air mode and turned the evo off and air mode just keeps going. Also Is there a way to turn of the up switch warning when turning it on?
Yes, Turnigy is a rebrand and they use the FlySky protocol. I can bind the 2A FlySky receivers with this radio and can also bind the Turnigy receiver with my FlySky FS-i6S.
I never said it was a copy of a FlySky. HobbyKing worked with FlySky to develop the Evolution. It's a Turnigy product for now. At some point the exclusivity contract will expire and FlySky will release their own version. The same thing happened with the i6S. This is totally normal for the industry.
Albert my brother, Quad, new radio, Interstellar, Leaf, tennis. How much more cool can you pack in a video? I don't even have a complete quad yet. I almost ordered a build just like your Martian ii build, but have chosen a little different parts here and there. Between you Joshua Bardwell, and Darke Peake, I feel like I have a great start on the whats and hows. Thanks! PS I tend to watch your videos at 1.5-2x speed and the piano piece sounds amazing at 1.5.
+Gary Crowell Interesting... how do you play it back at 1.5x?
The settings gear in the bottom right corner of the youtube screen.
Awesome.... thanks!
What's the difference between sbus and ibus?? Please answer
SBUS and iBUS are both serial UART protocols... One major difference is that SBUS is an inverted signal while iBUS is not. Otherwise fairly similar and both are much faster than PPM.
Hi Albert, So far so good! For someone like myself with very little knowledge of these RC Tx/Rx systems this video is soooOOOO helpful. Thank you!!
+John Graboski thanks for watching!
excellent video!.....
Hi Albert, for some reason I'm having trouble getting this radio to work with both my tarot130 and my TBS Powercube. Have you heard of this happening to anyone or have encountered this yourself?
+Light-on-Fuel FPV sorry, first time I've heard that.
Can not get an arm switch to show in beta flight, not sure what I’m doing wrong I followed along with your video, but still won’t arm, everything else works pid, all other settings are good, but won’t light up an arm switch in modes on beta flight, I think it might be a mapping issue but I’ve tried to rename channels, still know luck.
Any friendly advice would be greatly appreciated.
Thanks for all the great videos.
It's not that complicated. As explained in the video, you set a channel to a switch and it should show up in Betaflight configurator. If that isn't working for you, I don't know what the problem would be unless I had all the equipment in front of me to diagnose it.
Price is a bit high for a joypad style Flysky compatible transmitter , range is more important to me, ill see if i can grab a review sample as its not worth throwing money at something that falters.
thank u so much!
ok i have followed you as far as i can but when i go to the receiver tab nothing moves at all, i have it set to serial base and then to ibus and i have the same on the receiver set to the same as yours in not on a URAT 1,2 or 3 this is the wizzard and its on a IO1, how and why, please help
Did you check to make sure the receiver was in iBUS mode and not SBUS?
Please do a video on how to install the reciever into a riot 250r pro pleeeeaaaasssseeee
i don't have that model but if someone wants to send me one, I'd be happy to make such a video...
Albert Kim do you want me to send you a picture of the fc and you show arrows where the wires go
Hello.
I have a problem with failsafe. Done everything like you did,but nothing happens when turning off Evo tx.
I looked in betaflight receiver tab and after i turn off Evo tx ,the values just stays in last position.I have failsafe stage 2 enabled. Any ideas?
Thanks in advance
which receiver? what protocol? PPM? SBUS? IBUS?
rx is tgy-ia6c on ibus
Did you use switch arming like in my video? Then you can set the arm channel failsafe value in the transmitter.
Albert Kim yes , i did. Ok i will try that.
Hey guys, I'm new to drones and I can't get FC to recognize my stick movements. Betaflight 3.1 is set to RX/SBUS and turnigy controller set to PWM/SBUS. Controller seems to bind to the drone, but not getting any power to motors. Betaflight does not recognize my stick movrment. pls help!!!
James Choi did you find the solution, Same problem here
i came from your other video; i use mission planner for my pixhawk autopilot. so this will not be good for me or does it have nothing to do that.
Ah, I don't know anything about how to setup pixhawk, sorry. If you watched the other video, just setup one of the channels on any of the switches and you have to configure that channel for arming in the pixhawk. I just don't know how to do that for that FC.
This was a good video. Could you make a video on how to install this RX to your FC. I currently have s spektum radio that I'm get rid of for this new evolution it would be very helpful to have step by step video. Thanks for your help
There are hundreds of different FC's out there. So you would need to know where your connection to a UART is on your particular board. All you have to do is connect the signal (SBUS) pin to the RX of that UART port. Then connect 5V and GND anywhere on your FC, the source of the power doesn't matter.
Can u use the flysky fs-iA6 6 channel reciever with this transmitter
thanks that was very informative for a nub like me!
hi albert i wonder if you can me!! im going sell my frsky taranis and ive just order a turnigy evolution but my shuriken 250 is set up for my taranis which is the best receiver and is there any videos how to do it!! Tink UK
Are you asking which is the best receiver for the Shuriken 250? It already comes with the XSR receiver built-in... are you asking what Flysky receiver to replace it with?
Albert, Great video! Considering switching from Taranis to Evolution.
Should I get the FS-A8S to solder inside my QX90 F3 Board or should I just get the Banggood iRange 6CH Flysky Receiver? pros/cons?
Also, isn't having no trim buttons make flying a complete pain? Say I'm flying my QX90 inside with horizon/auto level mode and it's drifting. I would think trimming on the touch screen while controlling sticks would be disastrous or almost impossible. Currently I have to trim almost every time I fly the QX90. The no trim buttons seems terrible, can you correct my thinking on why it's not?
If the iRangeX Flysky receiver is the one I tested earlier and had failsafe crashes, I would not get that one. If there's another one out there, then I have no experience with it so can't say if it's good or not. I have about 10 of the A8S receivers and so far all are working OK for me. However, be aware some people are having issues with that receiver so there might be some bugs to be worked out. YMMV.
I don't use the trim buttons on my Taranis and don't need them. Most people probably should not use them in my opinion. It's fine for airplanes but not useful for multirotors with a flight controller. I recommend trimming the flight controller using Cleanflight stick commands instead. Search google for this, you'll see a lot of tutorials on it. This is the only way I will trim and also set level point on the accelerometer and the gyro. Once you do this, you'll find the quad won't drift anymore. Using these proper techniques the trim buttons have no purpose for multirotors and I for one am glad they are getting rid of that kind of airplane stuff that's not needed for multirotors.
One more question on the trims. Do you think the sub-trim feature could allow the evolution to be used as a decent fixed wing flyer? Assuming you can take 1 or two flights to dial in sub-trims and then have a straight flying craft. Is it naive to think this is possible?
+Luke Hawthorne Possible but not recommended as this would be very tedious. Also if the trims change later you will need to retrim again
thanks for the video. I have question. I followed your steps for setting up failsafe but it doesn't seem to work. when I turn off the tx the motors continue to spin. is there something else that's not covered in your video?
thanks again!
I would need more info about your setup. What receiver are you using? Cleanflight or Betaflight?
Albert Kim
I found the problem. I'm using an f303 XRacer v2.1 flight controller running BetaFlight 3.01 and to fix the issue I had to use sbus instead of ibus. Strange but now failsafe works!!
thanks again for all you efforts!
cheers
Hi
Could you please advise, Have changed back and forth from sbus to ibus and output from ppm to pwm ,still cant get the stick movement on betaflight all the switches respond. What am i missing. Thanks
Wow, could be so many things. I don't even know where to start. Perhaps the most likely case is that you are connecting the signal from the receiver to an inverted pad on the FC. You might want to try a different UART and pad that will be uninverted.
@@AlbertKimTV I will let you know, its strange as I say , all switches work , and you can see movement on the tx when the sticks move, the slides on channels move but not on \Betaflight
I changed my output mode to "S Bus" and my sticks are still not responding. Any suggestions?
There's some more information needed here. What kind of flight controller? What kind of receiver? Did you check that it is actually bound? Did you try IBUS instead of SBUS? Usually IBUS works better. Is your flight controller configured properly for serial receivers and you have the correct protocol selected?
can you show how to splice the wires for this receiver? I have a Diatone crusader gt 2 175 that I need to install it on..
So i just got my turnigy evolution in the mail, still waiting for my x220 wizard. How do i get betaflight,
I have some videos on my channel... here are a couple to get you started.
th-cam.com/video/81cqZanWa3Y/w-d-xo.html
th-cam.com/video/iLsSUNhTTnQ/w-d-xo.html
Jordon Cox I'm getting the same setup :) eachine wizard x220 and turnigy evo :)
what makes you choose uart1 or uart2 for serial rx. I saw uart2 used in another video. I dont understand what that port is.
Sometimes UART1 is taken by the USB port depending on what board you have.
Would this radio be compatible with any of the new RTF micro "tiny" models?
+Christian Cardona If the FlySky versions transmit in 2A mode then yes. Unfortunately I don't have one to test to confirm
What do u mean by inverted signal? Is sbus generally better than ibus
They are basically the same type of signal, just SBUS is inverted... inverted means that in a normal signal like iBUS, when the signal is low, SBUS is high (the opposite or inverted). That's the best way I can explain it. Beyond that, it's technical stuff I don't know about or care to know about. You would use one or the other depending on what equipment you had and that would determine what is "best" or most appropriate to use. For FlySky receivers I recommend using iBUS since it's the native protocol on that receiver. You can also use it on flight controllers that don't support inverting the signal on UART like the old Naze32 F1 boards. The newer F3 board support signal inversion in hardware.
Albert Kim so say I use a kakute f3 flight controller with the turnigy evolution then ibus should be fine? Also if I fly with other people that are using sbus, will ibus interfere with them?
+Jackaroo21 sbus and ibus won't interfere. I dont know about the Kakute. It probably supports ibus but you should check with the manufacturer
Albert Kim ok Thankyou. Do you just check on the website of the dealer? I will look around Thankyou lots mate!
any idea will this work with the old flysky ppm / pwm receivers, as i have loads of those already...?
Evolution only works with the new 2A (2nd gen protocol). I suspect it won't work with the older receivers. Sorry! 😭
have you built a 2nd gen unit Albert?? .... i cant seem to get the 2 to bind :( need some tips... no one has done a video yet...
Hi Albert, I just setup this radio last night and Im gettinh some nasty midstick jitter on all 4 channels. Wondering if I did something wrong. And btw 1520 is like futaba midstick, I left it as is.
Don't use SBUS, use IBUS instead. No jitter and no need to adjust center and end points. I will have a video about this in the near future. I just discovered this.
Awesome thanks 😄
can you show how your zmr is hooked up to the receiver
Fantastic, answered lots of my questions.
Is the S-BUS inverted like FrSky receivers?
I'm connecting to naze32 rev5, which I don't think accepts inverted sbus, so I'm hoping not.
And I'm really curious to see how often you reach for your taranis instead. Obviously in a different league, but how often are those extra features worth there weight?
I don't think it will work with a Naze32 Rev5. I used an F3 board and it was working.
Albert,
Can you tell if the TGY i6s firmware update will work on the Evolution as well? I would really like to see an extended menu with rates and throttle curve features like on my Flysky i6. Thanks
Actually it does not. I tried to connect it and the updater doesn't recognize it. We'll have to wait for Hobbyking to bring out the updater. FYI, if you're a multirotor pilot, I recommend you adjust rates and throttle curve in the flight controller. If you're trying to use this with a fixed wing plane, this radio is not designed for that and I don't even think they will include any fixed wing features in a future firmware update.
Albert Kim
I am using it for multirotor models,and I have heard the arguments of adjusting rates, etc through the FC software. But I like to be able to adjust things out in the field as i get used to a new model. It surprises me that the firmware isn't recognized, since the TGY i6s otherwise seems so similar
damn no trims! would have been the icing on the cake, could have used it for some park flyers as well :(
The bind cable usually goes on signal and ground so in this case sbus/gnd
It's not needed for binding. Plus, if you use the supplied bind plug as you have suggested, how do you power on the receiver? LOL
i can't get the télémetry to work, i have connected the main bat to b-det and set the rx voltage but still show low voltage on fully charge lipo. thanks
Assuming all your connections are good, you may have a faulty receiver. Have you tried another one?
i'm all set ! it works just fine. tks
Looks like there's still stick twitch even with this...So far the only transmitters I've seen that have had zero twitch are Spektrum :(
I've switched it over to IBUS and there's no twitching.
What's the difference between IBUS and SBUS? O_o
They're both digital protocols. IBUS is proprietary for FlySky radios.
which charger can I use to charge the battery of this control ?
Any USB charger like one for a smartphone will be OK.
hi albert , the failsafe on my turnigy evolution /i6C dont work , any ideas? i have set all ok , fail safe set to drop , Ibus working but my fail safe dont work (with previous fylsky receivers fail safe work ok)
+TheMascaras33 someone else in the comments had the same issue. He set his throttle to go below 900ms PWM value to get it to work.
with endpoints i can only go to 900ms , i set the safefail with that value but dont work .
Hmmm, not sure what's up. Mine is working and I don't have to do anything. Are you using cleanflight? betaflight? what versions?
What is the best receiver for the Turnigy Evolution?
+Passion Agar & Troll comments lol m9 get either iA6C or X6B
Anybody use this with FPV Freerider on Mac yet?
works great
which one do you prefer? between evolution and i6s?
The Evolution.
very informative video XD
the flight footage looks really good on the mobius you had...
which one is it and which settings do you use? (on mSetup.exe) i bought one and the video quality seems bad...
I think it was set to cloudy but I don't like that. Check that you have the latest version of the firmware. I think I also turned saturation down a little.
What FC do you use
I have a bunch of different ones. Omnibus F3, SPracing F3, Xracer303 V2, etc, etc.
ok thx
what can you fly with this? never see this listed when I look to buy a quad?
You need a receiver that can do the Flysky 2A protocol. More recent models can use this. For example the Eachine Aurora 90 with the Flysky receiver can fly with this - goo.gl/l4KJwt
h I see. yea i'm new at this and it got confusing with all the different controller and receivers. I got the Evolution and just ordered a couple Flysky FS-A8S for inductrix blade I have and the Eachine Turbine QX70. I think I can get it to fit in the qx70 but don't know about the blade. can't find the aurora 90 anywhere that is not on back order LOL just my luck. thanks for the help. love your channel !
just got my qx70 yesterday and it says on the box DSM2/DSMX did they send me the wrong one and can I still put the Flysky FS-A8S on it? thanks
thanks helped alot
RSSI low signal alarm?
I will look into that and the battery monitoring on a video about the receiver.
Did you ever end up figuring out how to get RSSI?
Can you use the evolution for simulators?
Yes, you just plug it into the USB port and it will be detected as a USB controller.
The zmr was my first quad 7yrs ago
Congrats
Hey how do I get the Servo test screen? Tnx
Hmmm, I don't think this firmware has that...
I am having a issue getting failsafe to work. My betaflight setting are the same as yours and I followed your instruction on the Evolution
what receiver are you using?
The one that comes with it. It has also worked with the taranis on this FC. I have even turned on Air mode and turned the evo off and air mode just keeps going. Also Is there a way to turn of the up switch warning when turning it on?
did you find the soluton? im having same problem (failsafe dont work)
no....
Turns out I got a Bad one and now have to wait 2-3 weeks for a replacement. Also the right gimbal is not registering
yes whick one for the turnigy evolution
I think the X6B will be the one most likely to fit however, I don't have the Shuriken anymore to test if it will fit in there or not.
Thanks i see when come mate. Your are great a lot of happy thanks again
Great review, thank you.
First
First
Love the looks great video!
Excellent in depth review. Really like the lil tx. Thanks
+MasterRC_sTudenT thanks!
No telemetry?
I'll have a video out tomorrow explaining what's up
It is not Flysky, It is Turnigy!
Yes, Turnigy is a rebrand and they use the FlySky protocol. I can bind the 2A FlySky receivers with this radio and can also bind the Turnigy receiver with my FlySky FS-i6S.
If that is true, why there isn't Flysky evolution (or what ever). My question is how do you know that tgy is copy of flysky? What if it is opposite?
I never said it was a copy of a FlySky. HobbyKing worked with FlySky to develop the Evolution. It's a Turnigy product for now. At some point the exclusivity contract will expire and FlySky will release their own version. The same thing happened with the i6S. This is totally normal for the industry.