wish I had tried this w my 2019 Prius yesterday! I have gigantic suction cups to take ole skool iMac glass off! I ended up buying a trim toolset & must have taken me an hour. the clear panel on RX350 is clearly gonna be so much easier when it comes time!
Thanks for showing how to change the interior lights. I did all the interior except the trunk. All three lights in the trunk used Festoon Bulbs. And if anyone has an issue removing the two front under the dash. It is easier to remove the cover (4 clips on the front passenger side and 1 clip & 2 screws on the driver side). For the 4 puddle doors lights. I used the Lexus logo. Remove the original and plug the new one in place.
Great video - love the troubleshooting. Before finding your video I was struggling to get that front dome cover off. I can see it's no easy task! Thanks for your patience - sorry about the burnt thumb.
Perfect video. I just got a 2010 IS350C and want to change the bulbs to led but I am always afraid I am going to break something. After watching your video I am fairly confident I can do it. Thanks.
Thanks for the vid. The hardest bulb to put in was indeed the rear dome (besides taking the cover off), especially positioning the one bulb into that perpendicular opening; fortunate I didn't have to pull down the assembly just took a lot of cursing and bulb dropping until I was able to put it in with pliers. I found out that if you hit the light off button on the headliner, those footwell lights would turn off so I don't know why you subject yourself to pain, unless its a 2013 and up RX thing only. The passenger well bulb was burned out anyway, so it was worth it to replace them both.
Thanks, video was helpful finding how to replace a bulb. Anyway just like at home inside my car i prefer warm white light so replacing to cold white LEDs for me not so good idea :) By the way for DOMES i have used wide knife - worked fine, do not use screwdriver you will damage plastic.
Ya it's a personal preference. For me the light is only something I need when it's dark outside, and I want to be able to see inside. So the LED light really helps me.
Did mine a few months ago and it made a huge difference !!!!!! You might want to get the Lexus Logo leds for your doors it shines the logo on the ground. The only ones I didn’t get to were the footwell lights. Thanks
Thank you for the video and recommendations. I have an RX-450H, and I used your suggestions to remove most bulbs. I still need to figure out how to change the door bulbs, as the wedge tool I have cannot get into the edges. I'll keep at it. Thanks again!!
To keep the lights from staying on and prevent burning yourself, open the doors and use a Phillips head screwdriver to push in the latch on each door. Just remember to pull the door handles before trying to close them.
I just finished upgrading all the interior led lights and I figured out a way to get the rear passenger dome light installed without having to remove the housing. The trick is to slide the led bulb head first into the groove kind of like changing out batteries for a tv remote since the led head area has some clearance room to slide in from an angle and once you have the bulb pushed in, you should be able to have the entire led inside the compartment and you can use a small pair of tweezer to guide the connector side in and once it’s in the groove, you can just use your hands and push it gently in. Also the plastic prying tool that comes with the led bulbs are a bit too thick. I would recommend to use a guitar pick or a jimmy tool. Makes opening all the plastic covers a breeze and comes off on the first time each time and you won’t have to worry about scratching any of the plastic trim pieces or break any plastic tabs on the cover
My shifter illimination went out so I was searching for videos and came across this one. Nice job! I think I will do the same. One thought, pulling the proper fuses(idk which ones) would make this less painful.
Great video, I recently purchased a 2010 Lexus rx350 and I would like to know if you have a video of changing the dull drl light to brighter ones? Thanks also where to buy?.
Thank you for taking the time to make this video, very detailed and complete. Got me laughing also, you changed 9 bulbs and burned yourself about 16 times. lol
Hey, thanks a lot for sharing this video, I noticed that you didn't replace the lights on the left and right sides of the trunk, did you? They also have switches, so would they be the same model as the light on the trunk lid?
Hi, sorry it took me so long to look in the trunk, you are right! Those are different specific lightbulbs that I purposefully didn't replace because I never use them.
Hey! Wanted to ask. Are your lights still functional after this long? Just worried I gotta pop all these out within a year due to flickering or something
great videos!...are these LEDs dimmable like the incandescent lamps that get removed?... I'm about to do the rear shocks in my 2010...I'm hearing a clunking noise when I go over even a small bump...wondering if there's a bolt loose in the right rear shock assembly, or if the shock ( could be original at 167k miles) is simply giving zero resistance...thoughts? Thanks!
Hi, sorry for the late reply I was out of the country. Your bushings could be worn out, or the shock bolt could be loose, check your lug nuts also, or the shock could just be bad. With that many miles, and it's so simple and pretty cheap to replace, it likely would make a noticeable difference in performance and maybe fix the noise as well. Regarding the LED's yes I believe they are all dimming as they should be I just never paid attention to it.
I feel ya but it won't be so warm when u discover yr incandescent lights drained yr battery on top of a mountain! 😅 this literally happened to me in a Prius less than 4 yrs old & just finished swapping to LEDs before my next trip. Im sure the warm color is exactly why they stick w incandescent bulbs esp on the visor vanity mirror (I debated leaving those esp on the front passenger side!)
bet they just included it in the earlier ones to stand out from other kits. it admittedly a nice touch. I just invested in a $6 trim tool kit which worked great.
a trick i learned from another video to remove bulbs is to wrap the bulb in painter's tape to create a tab to pull on. i used masking tape which worked great.
Hey i have an RX 350 2010 and am wondering if there is a way to bluetooth the phone for music through the stereo.As it stands it will only Bluetooth phone calls...any adapters around that would do this ...cheers thankyou for your great vlogs!!
The visor lights (vanity light bulbs) are called FESTOON bulbs, Depending on the make and model of your car, their sizes ranges from 31mm to 42mm. Thanks for the upload!
FWIW, the 31mm festoon bulbs needed are a but too long but will work. You must bend the fixture ends that the bulb goes into some to accommodate the added length.
lol don't change the bulb if it's hot. . Use an old debit or credit card and slide along one side of the done light and it pops right out. Just wiggle the bulb afterwards.
bought the same brand of leds and did this over the weekend. thanks so much from another RX350 owner in North Carolina.
Awesome!
I replaced the 4 puddle door lights with LEDs with lense showing the Lexus logo. Everything else I did just like you showed. Thank you for the video.
Glad it helped
A great way to remove some dome lights and covers is using a suction cup that you would find with a phone repair kit. Usually works like a champ.
Good tip!
wish I had tried this w my 2019 Prius yesterday! I have gigantic suction cups to take ole skool iMac glass off! I ended up buying a trim toolset & must have taken me an hour. the clear panel on RX350 is clearly gonna be so much easier when it comes time!
This almost never works
Thanks for showing how to change the interior lights. I did all the interior except the trunk. All three lights in the trunk used Festoon Bulbs. And if anyone has an issue removing the two front under the dash. It is easier to remove the cover (4 clips on the front passenger side and 1 clip & 2 screws on the driver side).
For the 4 puddle doors lights. I used the Lexus logo. Remove the original and plug the new one in place.
Nice job!
Great video - love the troubleshooting. Before finding your video I was struggling to get that front dome cover off. I can see it's no easy task! Thanks for your patience - sorry about the burnt thumb.
LOL no problem, I'm glad it was helpful!
Perfect video. I just got a 2010 IS350C and want to change the bulbs to led but I am always afraid I am going to break something. After watching your video I am fairly confident I can do it. Thanks.
Awesome, good luck
Thanks for the vid. The hardest bulb to put in was indeed the rear dome (besides taking the cover off), especially positioning the one bulb into that perpendicular opening; fortunate I didn't have to pull down the assembly just took a lot of cursing and bulb dropping until I was able to put it in with pliers.
I found out that if you hit the light off button on the headliner, those footwell lights would turn off so I don't know why you subject yourself to pain, unless its a 2013 and up RX thing only. The passenger well bulb was burned out anyway, so it was worth it to replace them both.
Nice job! Ya that dome was definitely the hardest one
Thanks, video was helpful finding how to replace a bulb. Anyway just like at home inside my car i prefer warm white light so replacing to cold white LEDs for me not so good idea :) By the way for DOMES i have used wide knife - worked fine, do not use screwdriver you will damage plastic.
Ya it's a personal preference. For me the light is only something I need when it's dark outside, and I want to be able to see inside. So the LED light really helps me.
Did mine a few months ago and it made a huge difference !!!!!! You might want to get the Lexus Logo leds for your doors it shines the logo on the ground. The only ones I didn’t get to were the footwell lights. Thanks
I didn't know they had lights that shine a logo, that's cool but I bet you have to replace the plastic too
Hey CC is there anyway I can send you an Email ?
Don’t forget to shoot me your email CC Thanks
@@tbates860 You can email me at ermishes@gmail.com
I did 4 doors, 2 front foot wells, 2 front dome lights, and 2 visor lights. Thanks for the video.
Nice work!
Thank you for the video and recommendations. I have an RX-450H, and I used your suggestions to remove most bulbs. I still need to figure out how to change the door bulbs, as the wedge tool I have cannot get into the edges. I'll keep at it. Thanks again!!
Glad to help, good luck!
To keep the lights from staying on and prevent burning yourself, open the doors and use a Phillips head screwdriver to push in the latch on each door. Just remember to pull the door handles before trying to close them.
Burning myself makes for better videos
@@CarolinaCowboys lol
I just finished upgrading all the interior led lights and I figured out a way to get the rear passenger dome light installed without having to remove the housing. The trick is to slide the led bulb head first into the groove kind of like changing out batteries for a tv remote since the led head area has some clearance room to slide in from an angle and once you have the bulb pushed in, you should be able to have the entire led inside the compartment and you can use a small pair of tweezer to guide the connector side in and once it’s in the groove, you can just use your hands and push it gently in. Also the plastic prying tool that comes with the led bulbs are a bit too thick. I would recommend to use a guitar pick or a jimmy tool. Makes opening all the plastic covers a breeze and comes off on the first time each time and you won’t have to worry about scratching any of the plastic trim pieces or break any plastic tabs on the cover
nice job!
wondering if the slim, flat T10 bulb might be easier?
My shifter illimination went out so I was searching for videos and came across this one. Nice job! I think I will do the same. One thought, pulling the proper fuses(idk which ones) would make this less painful.
Or use gloves :-)
how are these led bulbs working out for you? too many of these types of cheap leds die out too fast
Ya you never know, but all my bulbs are still working good.
You will feel the difference the LEDs and housing are cool to the touch. And at night you can see everything. The DOMES were the toughest for me.
I'm surprised how bright these things are! I'm going to do the backup lights next
Great video, I recently purchased a 2010 Lexus rx350 and I would like to know if you have a video of changing the dull drl light to brighter ones? Thanks also where to buy?.
Hi, that's a great idea, I will look into it and make a video on that, stay tuned!
@@CarolinaCowboys back lift door solutions also, mine keeps closing after it fully open it beeps then comes down? Thanks again
@@tyreelockhart4879 check here th-cam.com/play/PLXKlNXcI_kmN2ufAx5mGTB1O5XqTcwiHZ.html&si=97Zd2nh7PfIfSdrO
Great and clear instruction. Thank you
You are welcome!
Great video, just what I needed!
Glad it helped!
Thank you for taking the time to make this video, very detailed and complete.
Got me laughing also, you changed 9 bulbs and burned yourself about 16 times. lol
LOL, yes they kept getting me
Hey, thanks a lot for sharing this video, I noticed that you didn't replace the lights on the left and right sides of the trunk, did you? They also have switches, so would they be the same model as the light on the trunk lid?
Hi, sorry it took me so long to look in the trunk, you are right! Those are different specific lightbulbs that I purposefully didn't replace because I never use them.
Thank you, helped me to deal with rear seat light, was tuff one.
Glad it helped!
Hey! Wanted to ask. Are your lights still functional after this long? Just worried I gotta pop all these out within a year due to flickering or something
Yep they're all still working!
you the man , thank you , I will be ordering the kit now
Awesome
Thanks for the awesome walk through. Will use your knowledge to do the same to mine. Appreciate this
Glad it was helpful!
great videos!...are these LEDs dimmable like the incandescent lamps that get removed?... I'm about to do the rear shocks in my 2010...I'm hearing a clunking noise when I go over even a small bump...wondering if there's a bolt loose in the right rear shock assembly, or if the shock ( could be original at 167k miles) is simply giving zero resistance...thoughts? Thanks!
Hi, sorry for the late reply I was out of the country. Your bushings could be worn out, or the shock bolt could be loose, check your lug nuts also, or the shock could just be bad. With that many miles, and it's so simple and pretty cheap to replace, it likely would make a noticeable difference in performance and maybe fix the noise as well.
Regarding the LED's yes I believe they are all dimming as they should be I just never paid attention to it.
Have you also done the license plate lights? Presume these are the same as the interior lights.
I've never thought about that! You might have found the mysterious 10th bulb!
Nice! To eliminate the pain I would disconnect the battery and have functional cool fingers to make the job easier.
I think I must like pain because I always forget to do it
I find the warmth from halogen bulbs nicer for interior lights
Ya it's a personal preference. I'm happy with these LED's
I feel ya but it won't be so warm when u discover yr incandescent lights drained yr battery on top of a mountain! 😅
this literally happened to me in a Prius less than 4 yrs old & just finished swapping to LEDs before my next trip.
Im sure the warm color is exactly why they stick w incandescent bulbs esp on the visor vanity mirror (I debated leaving those esp on the front passenger side!)
Bought the same brand lights but no tool inside
Strange
bet they just included it in the earlier ones to stand out from other kits. it admittedly a nice touch. I just invested in a $6 trim tool kit which worked great.
Does the 2015 model have the same light housing?
The 2010-2015 should be the same
This Video helped me out a lot, Thanks.
Awesome!
Subbed! Do the LED lights still fade on when opening the door?
Awesome! Yes all the fading still works, and looks even better with the LED's
Will this work for 2004 Lexus ES330?
It should be the same, but don't quote me on that!
Honestly thank you everyone wants to put strips, NO I want bulbs
Did you change the outside mirror lights?
Oh wow I didn't realize there were lights in the mirrors?
a trick i learned from another video to remove bulbs is to wrap the bulb in painter's tape to create a tab to pull on. i used masking tape which worked great.
Great tip!
For the Way Back lights, measure the length of the bulb, source from DiodeDynamics. Same for the light on the trunk lid.
Ya I just forgot about those lights
Hey i have an RX 350 2010 and am wondering if there is a way to bluetooth the phone for music through the stereo.As it stands it will only Bluetooth phone calls...any adapters around that would do this ...cheers thankyou for your great vlogs!!
Yes there is a way and it actually took me a long time to figure it out. I will make a video for it, thanks for the idea!
@@CarolinaCowboys Great !! LOOK FORWARD TO IT.
There is, it actually took me a long time as well you have to register the phone as a portable player but as the boss said he's gonna do a video
@@KBlessLiving I recently posted the video th-cam.com/video/KXCp4uWDZ6E/w-d-xo.html
@@KBlessLiving cheers thanks
Thanks for this video! It was of great help. To easily pull the bulbs, I put a piece of masking tape on the bulbs and that will give enough grip.
Good idea!
Hi, could u let me know what kind of led is this KIT? There are many options on this Yorkin website. Thx!
Hi, I put the link in the description!
Very helpful 👍 . Thank you
Glad to help!
Can you show how to replace the license plate bulb?
Yes definitely!
In the front Dom lights one of the light housings slipped into the back any idea on how to remove the whole housing so I can retrieve it?
Which dome light, the front or the rear?
Great video
Thanks!
Did you remember the glove box?
Uhh, is there one in the glove box?
10 plus one more on the tailgate and the front one on the roof have 2 bulbs total of 12
Your right!
There is a light in the visor when you slide the mirror
Your right!
How do you replace the bulb?
Just pull it straight out of the socket and the new one pops right back in
Great vid 👍🏾
Thanks!
The visor lights (vanity light bulbs) are called FESTOON bulbs, Depending on the make and model of your car, their sizes ranges from 31mm to 42mm. Thanks for the upload!
and yeah, the festoon bulbs also comes in SMD or LED.
Good to know!
FWIW, the 31mm festoon bulbs needed are a but too long but will work.
You must bend the fixture ends that the bulb goes into some to accommodate the added length.
Don’t forget the one in the inside of the tailgate door.
Are you referring to another light that I didn't show at 19:00?
10th bulb is on the lift gate
Your right!
Thanks! this video helped me alot on my install after following all of your steps. The Yorkim lights work great, too!
nice job!
lol don't change the bulb if it's hot. . Use an old debit or credit card and slide along one side of the done light and it pops right out. Just wiggle the bulb afterwards.
Nice! Yes my videos sometimes show what not to do. :-)
grateful for your share. Just finished upgrading mine.
Nice!
You missed vanity mirror lights
Oh ya I did find those after the video! I noticed it uses a weird bulb tho
they are prolly better left incandescent - looking in the mirror you'll look less ghostly 👻
i laughed when you counted three in the trunk which need different type of led…should read or search before dig in.
LOL you will probably laugh at more of my videos then because that's how I record them
You forgot the glove box
Is there a light in there?
Those lights they melt on the back , you can get the flat ones solid. Als oh yeaho you forgot the visors mirrors lights.
Thanks!
@Lucas T which flat ones? Do you got a link to the flat ones?
wow the missed count is going up fast! like to know what the new grand total is!
Arm rest has a light
Arm rest? where?
Maybe you should just close the door and the bulb won’t be hot. You’re as bright as a bulb
Thanks for the encouragement, I knew there was a reason I left the bloopers in!