Hey, is there any other advantage to use the lemo export from the hand contoller? For example communicating with a monitor about the focal distance? Because the Teradek RT System is able to show a focus parameter scale on the right side of the monitor it is connected to. Therefore the 1. AC will know where his focus is right now, without looking to the hand unit, which I think is very useful, because it reduces a lot of stress.
Great video, can you clarify however... when assigning channels, you say to place all the motors on different channels. Does that mean you must manually change them if you wish to use the hand unit for 3 motors? Also how can you have focus on one nob, zoom on the joystick and iris on the other nob? I noticed in the EZ video all motors were set and stayed on the same channel. Please advise. Thank you for the videos
The original method for syncing Motors to Controllers is as follows: Motors and Controllers must be set to the same "LORA" and Channel, for example: "H 08" "H" is "LORA" and "08" is the channel. Once all the motors and controllers are "H 08" then each motor is assigned a "motor number". You can decide the motor number per motor, 1-4. Then in the menu of the FIZ you can decide which "motor number" will be controlled by what. If your motor, assigned motor number 1, is on the focus ring of your lens then you will sync the controller knob on the FIZ to motor 1. If your motor, assigned motor number 2, is on the iris ring of your lens then you will sync the iris wheel controller to motor number 2. If your motor, assigned motor number 3, is on the zoom ring of your lens then you will sync the zoom joystick on the FIZ to motor number 3. EZ Mode uses a different protocol to sync all the motors and controllers, but the former method I've explained above still works. If you have any more detailed questions please email support@tilta.com
Here's the link for recommended batteries. www.walmart.com/ip/4-PCS-3-7v-6000mAh-18650-Rechargeable-Li-ion-Battery-Dual-Travel-Charger-USA-Stock/182643265
"Motor protection please Recal" I got these problem on my motor. Do you know what the problem is? and how to fix All of my motors are not working. Plz help!
This will happen when the voltage of the motor is not stable. It could be that there is not enough power or too much power going into the motor. This is a self-protection mode. Have you tried other ways of powering your motor?
@@TILTA Hello, which device do you suggest to give stable voltage to achieve a good motor quality? is it a bad idea connecting the motor straight to the battery?
This is not a helpful guide at all. Showing how things are already set up, not explaining what different settings are, and not showing how to change settings makes for a pretty miserable guide.
This was indeed a very QUICK guide. Now, where can we found the slow guide?
Hahaha
Hey,
is there any other advantage to use the lemo export from the hand contoller? For example communicating with a monitor about the focal distance? Because the Teradek RT System is able to show a focus parameter scale on the right side of the monitor it is connected to. Therefore the 1. AC will know where his focus is right now, without looking to the hand unit, which I think is very useful, because it reduces a lot of stress.
Great video, can you clarify however... when assigning channels, you say to place all the motors on different channels. Does that mean you must manually change them if you wish to use the hand unit for 3 motors? Also how can you have focus on one nob, zoom on the joystick and iris on the other nob?
I noticed in the EZ video all motors were set and stayed on the same channel.
Please advise.
Thank you for the videos
The original method for syncing Motors to Controllers is as follows: Motors and Controllers must be set to the same "LORA" and Channel, for example: "H 08" "H" is "LORA" and "08" is the channel. Once all the motors and controllers are "H 08" then each motor is assigned a "motor number". You can decide the motor number per motor, 1-4. Then in the menu of the FIZ you can decide which "motor number" will be controlled by what. If your motor, assigned motor number 1, is on the focus ring of your lens then you will sync the controller knob on the FIZ to motor 1. If your motor, assigned motor number 2, is on the iris ring of your lens then you will sync the iris wheel controller to motor number 2. If your motor, assigned motor number 3, is on the zoom ring of your lens then you will sync the zoom joystick on the FIZ to motor number 3. EZ Mode uses a different protocol to sync all the motors and controllers, but the former method I've explained above still works. If you have any more detailed questions please email support@tilta.com
How do you trigger the camera REC button?
You need to correct cable to connect to your camera. Then it just works like any other lanc control, but the only thing it does is R/S
How did you get the arri rosette mount on the hand unit focus puller? Isn't it just flat wood behind it?
DTChunky they sell a rosette bracket and clamp for tubing.
No batteries included is a nightmare to get them. bad Technical support.
Can you attach monitor to single control unit?
Alright, How do I setup record butten?.
Hey, where can I find that stand for the FIZ unit? Thanks in advance! Flo
Can you provide a link to buy correct batteries here? Thank You
www.sears.com/ultrafire-18650-battery-6000mah-3.7v-li-ion-rechargeable/p-A040809173?plpSellerId=winnerway2018&prdNo=1&blockNo=1&blockType=G1
The page on there website that this product is on has a link of battery that they suggest to use. I got 20 rechargeable batteries for $10!!!
Search amazon for 18650 battery
What brand of 18650 batteries are people using?
Here's the link for recommended batteries.
www.walmart.com/ip/4-PCS-3-7v-6000mAh-18650-Rechargeable-Li-ion-Battery-Dual-Travel-Charger-USA-Stock/182643265
Use the suggested batteries that’s on there website. They provide a link on the product page. They’re only $10 for 20 rechargeable 18650.
"Motor protection please Recal"
I got these problem on my motor. Do you know what the problem is? and how to fix
All of my motors are not working. Plz help!
This will happen when the voltage of the motor is not stable. It could be that there is not enough power or too much power going into the motor. This is a self-protection mode. Have you tried other ways of powering your motor?
@@TILTA Hello, which device do you suggest to give stable voltage to achieve a good motor quality? is it a bad idea connecting the motor straight to the battery?
where can I find that stand for the FIZ unit please?
That is actually just a display piece for our show demos.
Gonna be honest... this dark looking video doesnt work
why when i put calibrate the motor dont stop from working
This is not a helpful guide at all. Showing how things are already set up, not explaining what different settings are, and not showing how to change settings makes for a pretty miserable guide.
Please see our other tutorials for more specific information about different settings and instructions for setting up the system!
Way too fast. Useless, in fact.