It works! Got my unlocked speed on the M365 Pro up to 31km, but since my payload is 75kg it slightly dipped around 29-30km lol, plus it does consume slightly more battery life as well since its not locked to 25km/hr now.
hi this is exactly the same with mine at the moment but i am a little confused. under "change current in sport mode" there is sport max current which is set at 40000 mA (although can be adjusted) and sport max battery current which is set at 20000. I fear for my battery so i dont have it damaged, should i leave these parameters the same or adjusted?
@@thelonealpha17 I just followed the guide but I adjusted the speed of Eco to 18km/hr, and Sports mode up to 35km/hr now hehe! Draw back is the battery life may drain a little unless you use cruise control.
Well, this is a good way to get the performance you want out of your scooter but you also run the risk of ruining your scooter big time because it wasnt built to accommodate these types of modifications. Modifying them will also void the warranty if the scooter has one. If you want a high performance scooter, it’s best to just spend the extra money and buy one that already comes with fast speeds. Fast high end scooters are typically 3200watts and over and cost anywhere from $1,000-$5,000. You get what you pay for. Being cheap and shortcutting by modifying a cheap M365 scooter to go faster won’t do anything for you but leave you with a broke scooter eventually. Modifying a cheap slow scooter to go fast is just not a wise thing to do. The engineers that built the scooter gave it the specs that it has for many reasons.
in some ways i agree but again, if you are only changing the settings slightly, then it should not be a big issue other then your distance will be less then the original settings. The settings from the factory install is super safe and set to a standard that is basically guaranteed not to cause any problems. having the scooter gain 5 more kmt on the top speed should not do much to the motor or battery but if you change the acceleration which is where the most pressure on the motor + battery is, then it can have a serious effect and might end up ruining your battery or fry up your motherboard on the scooter. I am hoping to get a m365 Pro soon and I will surely be flashing the firmware to give the speed mode a max of 30 kmt + i will also increase the accelleration from the stock, maybe to 47.500,- instead of the stock 52.000, it is a minimal change and finally, instead of lowering the speed where the motor is supposed to kick in, i would change that from 5 kmt to maybe 7 or 8 so there will be less stress on the pull :)
If you set the setting of the max engine current lower than stock 55A, you've decreased the engine power. If you want to increase the power, you need to increase the amperage. If you set it too high, the scooter will go into limp mode and will not accelerate. Try changing it back to stock sport mode 55A and you will see it goes faster, reaching max speed of 33kmh. Let me know when you try it.
I have tried different options. This one offers the best balance: acceleration, speed, battery, braking. If you want to see, have a look at my videos as I have one testing the maximum possible speed...35kmph
Amazing. I have 1.6.0 stock version and will give it a try.. would be nice to know about the other values of the cfw configurator! One problem here, for the pro version, in this page, you can’t change motor power constant anymore...
I have subscribed. Thank you for the video. I've seen on other videos that before hacking the scooter with a custom firmware, you need to install another BLE (Bluetooth software) or the scooter will be bricked. I have the BLE 1.10 and would need to have 0.9.0 Do you know if it's correct? Thank you
No problems so far. Temperature is ok, maximum 48 degrees C. Max speed is 29-30kmph, one full battery lasts for approx 31km (vs 36 before). The acceleration is much better now and I can climb more inclined slopes now.
@@MonkeyUK. how i did it was get the 365GO app then went to uldate firmware them st 11% i closed down the app then did the firmware again and the used the 11k firmware then i went to the speed settings then clicked i think 45kph but only thing is the button wont turn on the light or change speed mode that needs to be done all on phone
Hi, I have a xiomi 365 pro.. I have version 1.6.8 I can't find the way to make the firmware. Do you know how to do it? The firmware in internet are 1.5.5 or 1.3.8. Tell me know. Thanks
In all honesty, they should sell these speed limit free, or else raise it to 19mph, the ridiculous 15.5 is stupid. Every scooter rider should be made to do an online safety course, where they receive a certificate that qualifies them to use a E scooter, I have seen some real idiots speeding on scooters 🛴 in very busy pedestrian areas. When in a very busy location, speed should be held to 5/9 mph.
@@SilverHunkClover it goes on 32 khm speed normaly on this hack and 37 down hill, i have been using it in Icelandic weather and roads. Without the hack it takes me 30 min to go to work. With the hack it is 20 min.
@@recanything did you lose any acceleration? I've seen some people (different video) say that it's has more top speed now but takes longer to get to top speed. With one comment saying that he struggles more now with a steep hill that it could go up before... Have you notice any difference, good or bad, with acceleration?
@@Until_It_Is_Done well...if you don't want to lose power, you have to play with the power constant. I have it at 43000 and I have the same power as before.
@@ReeceorRF oj okay, its complicated...i have a legal german 20 kmh m365 clone with licence plate and i transplanted the technics into from original m365 to drive faster as 20 kmh ^^ xD
5 months and not a single problem so far...it works like in the 1st day. I noticed that when the battery level goes below 50%, the max speed goes from 30kmph to 26-27 kmph.
I have a clone M365 from AliExpress it connects only whit this app called “Youfs” Can anyone suggest any of those hacks that can help me increasing the speed on my scooter using this app ? Thank you so much in advance for any useful advices 😎
What version do you have on your scooter? If it's 1.6.6...it's not working. If you have older version, try to restart the scooter and make sure you don't have other app connected to it. Also, activate wifi and location on your phone.
0:51 who cares what you will have. you downgrade it LOL.and then its not latest LOL.and come day when you upgrade latest.downgrade not work.until someone hack it again LOL. might be long time if hacer has allreadt what he like LOL
It works! Got my unlocked speed on the M365 Pro up to 31km, but since my payload is 75kg it slightly dipped around 29-30km lol, plus it does consume slightly more battery life as well since its not locked to 25km/hr now.
hi this is exactly the same with mine at the moment but i am a little confused. under "change current in sport mode" there is sport max current which is set at 40000 mA (although can be adjusted) and sport max battery current which is set at 20000. I fear for my battery so i dont have it damaged, should i leave these parameters the same or adjusted?
@@thelonealpha17 I just followed the guide but I adjusted the speed of Eco to 18km/hr, and Sports mode up to 35km/hr now hehe! Draw back is the battery life may drain a little unless you use cruise control.
I have v 1.6 but this hack works for me, thank you
Well, this is a good way to get the performance you want out of your scooter but you also run the risk of ruining your scooter big time because it wasnt built to accommodate these types of modifications. Modifying them will also void the warranty if the scooter has one. If you want a high performance scooter, it’s best to just spend the extra money and buy one that already comes with fast speeds. Fast high end scooters are typically 3200watts and over and cost anywhere from $1,000-$5,000. You get what you pay for. Being cheap and shortcutting by modifying a cheap M365 scooter to go faster won’t do anything for you but leave you with a broke scooter eventually. Modifying a cheap slow scooter to go fast is just not a wise thing to do. The engineers that built the scooter gave it the specs that it has for many reasons.
in some ways i agree but again, if you are only changing the settings slightly, then it should not be a big issue other then your distance will be less then the original settings. The settings from the factory install is super safe and set to a standard that is basically guaranteed not to cause any problems. having the scooter gain 5 more kmt on the top speed should not do much to the motor or battery but if you change the acceleration which is where the most pressure on the motor + battery is, then it can have a serious effect and might end up ruining your battery or fry up your motherboard on the scooter. I am hoping to get a m365 Pro soon and I will surely be flashing the firmware to give the speed mode a max of 30 kmt + i will also increase the accelleration from the stock, maybe to 47.500,- instead of the stock 52.000, it is a minimal change and finally, instead of lowering the speed where the motor is supposed to kick in, i would change that from 5 kmt to maybe 7 or 8 so there will be less stress on the pull :)
I will upgrade it to 35km but i will use it sensible
Worked for me👍
I have version 1.7.1
If you set the setting of the max engine current lower than stock 55A, you've decreased the engine power. If you want to increase the power, you need to increase the amperage. If you set it too high, the scooter will go into limp mode and will not accelerate. Try changing it back to stock sport mode 55A and you will see it goes faster, reaching max speed of 33kmh. Let me know when you try it.
I have tried different options. This one offers the best balance: acceleration, speed, battery, braking. If you want to see, have a look at my videos as I have one testing the maximum possible speed...35kmph
Dude u r King, the best tutorial ive found to flash the shit out of your scooter 🙏🏽
Amazing. I have 1.6.0 stock version and will give it a try.. would be nice to know about the other values of the cfw configurator!
One problem here, for the pro version, in this page, you can’t change motor power constant anymore...
Yep...
The Motor Power Constant not showing and only V1.5.5 and V1.5.2 in software version tab ?
"Cruise control delay is 5 kilometers per hour" xDDD
lol
Faster sure, less distance certainly
It's logic lol
Make it slower then and get more range 👍🏼
Did work 👍🏽
Where did you buy the kids handlebar mounts? Thinking of buying the same setup for my school runs 🏫
www.banggood.com/buy/xiaomi-m365-handlebar.html
Dude PLS help me, i need to know how i get my old Firmware Back?
There's a new hack
I have subscribed. Thank you for the video. I've seen on other videos that before hacking the scooter with a custom firmware, you need to install another BLE (Bluetooth software) or the scooter will be bricked. I have the BLE 1.10 and would need to have 0.9.0
Do you know if it's correct?
Thank you
I try to upgrade my xiomi 365 to 1.5.2 firmware and it doesn't work can u pls help me to put it back on version 151 pls..
Hi, would this work on a “HAPPYRUN M365 pro”? Many thanks
So, how is it now with full battery, how fast does it go and are there any problems?
No problems so far. Temperature is ok, maximum 48 degrees C. Max speed is 29-30kmph, one full battery lasts for approx 31km (vs 36 before). The acceleration is much better now and I can climb more inclined slopes now.
I am on version 1.6.1 as you were, but there is not a version 1.6.1 to choose from on the page. What should I do? Any ideas?
Choose 1.6.0. It's working. This is what I did
@@recanything What if you only have 1.5.5 option in the dropdown? Have they redacted the others?
Why dose it ask the access camera and Location
Hello guys i have pure air pro scooter how i do this on my scooter?
I just bought a new scooter, and now they are shipping them with version 1.6.6
You can still downgrade. Got main downgraded to 1.5.5. though you need to flash the BLE90
Grey Wings wait are they actually?
Got my one to go 28mph from the 19mph top speed how so i get it to go faster
What speed did u put in I am 8n mph .
He sed +2 or somethink
But 30kph +2 is not the speed you got n8ce please help
@@MonkeyUK. how i did it was get the 365GO app then went to uldate firmware them st 11% i closed down the app then did the firmware again and the used the 11k firmware then i went to the speed settings then clicked i think 45kph but only thing is the button wont turn on the light or change speed mode that needs to be done all on phone
The version you choose is not the version you have installed on your scooter, but the firmware version you want to put on!
Of course...because on my scooter I had 1.6.1 and the software only knows 1.6.0. But it works!
@@recanything On the 1.6.1 you can install 1.5.2 , 1.5.5 or 1.6.0. You can choose the version of cfw you prefer
thanks
Does this work with the normal m365?
Hi, I have a xiomi 365 pro.. I have version 1.6.8 I can't find the way to make the firmware. Do you know how to do it? The firmware in internet are 1.5.5 or 1.3.8.
Tell me know.
Thanks
Did you find a way mate?
@@MarreLirre hi folk.. No nothing!.
Can you help me?
@@ettorecarucci9744 My best bet is this video, not sure if it works with 1.6.8, try ask around there
watch?v=nlhz8XJFMYg
@@MarreLirre thanks man
@@ettorecarucci9744 No problem, good luck! Tell me if it works, I've not tried yet, I have 1.6.0, but a lot of people seem happy in the comments
In all honesty, they should sell these speed limit free, or else raise it to 19mph, the ridiculous 15.5 is stupid. Every scooter rider should be made to do an online safety course, where they receive a certificate that qualifies them to use a E scooter, I have seen some real idiots speeding on scooters 🛴 in very busy pedestrian areas. When in a very busy location, speed should be held to 5/9 mph.
Anyone know how to dertrictiom off zipper 800
If it doesn't work downgrade your Bluetooth (BLE) to 072 first through the downgrade app and u should be able to flash it from there
This is for the non pro version of the m365 btw
How do I do that?
After the firmware my headlight is not working
Does it work even with 1.7.1 firmware...?
Yes you have to downgrade your bms
Ble
Takes 20 mins to flash them install gonka 155
this hack also goes for a normal scooter like normal m365 not m365 pro
mine is 1.5.6 what should i do
There is a better hack you can use to increase the speed. And the top speed 33 km/h works only with full battery to 60%
What is that hack
@@SilverHunkClover it goes on 32 khm speed normaly on this hack and 37 down hill, i have been using it in Icelandic weather and roads. Without the hack it takes me 30 min to go to work. With the hack it is 20 min.
I cant cant the version..what do I have to do
How about 1.5.4 it works?
Can't even pair the scooter to my phone.
That's the end of that then.
Anyone got a hacksaw or angle grinder?
Does it works with iphone.??
M
M
Mq
Nope
Can you use iPhone....??
How much range decreased after this modification?
I lost about 20% of battery.
@@recanything Thank you. That's useful to know!
@@recanything did you lose any acceleration? I've seen some people (different video) say that it's has more top speed now but takes longer to get to top speed. With one comment saying that he struggles more now with a steep hill that it could go up before... Have you notice any difference, good or bad, with acceleration?
@@Until_It_Is_Done well...if you don't want to lose power, you have to play with the power constant. I have it at 43000 and I have the same power as before.
@@recanything good to know, thanks! Might give it a shot, just some negative comments worry me..
and the test ???
Not work on 1.6.6
😂
1.6.6 it is not supported by the DownG app currently. The only way to do it now it's to change the controller....
@@recanything but can i modify it in future?
@@null-xv3eq only if the guys developing the DownG app will manage to hack the new security imposed by 1.6.6....don't know
Motor Power Constant is not shown anymore. I guess they have removed cause there is a risk of damage of the engine. Cheers from Manila
m365DownG app can not check version of my scooter, I have 1.6.6 version..
Is there any other way to downgrade it ??? Please anyone?
The app was updated, you can now use it to downgrade the BLE and then you can flash custom firmware.
Mine went 35kn from the shop
the best firmware is the oem xiaomi
9:29 dont use mi home if you hack it LOL its useless app you never need use it
If i restore to factory settings after this.....Does the warranty be acitve again? if i need or the warranty be lost for good if i do the hack?
the stupidity of some people that unfortunately share the same timeframe and planetary body is beyond worrisome.
Hello I have version 0171.Can I do it?
Yes you can, not this way tho. Did you do it already?
Hello,
If I want scooter to go 35km/h, will that damage my motor?
Thanks
you cant go 35 kmh. maybe you can drive 29 if youre good^^
Mine goes 33km/h😂
@@ReeceorRF mine goes just 27 kmh but iam fat LOL
Bergwacht yhh im very light that’s probably why , what version do u have ive got the mi m365 pro
@@ReeceorRF oj okay, its complicated...i have a legal german 20 kmh m365 clone with licence plate and i transplanted the technics into from original m365 to drive faster as 20 kmh ^^ xD
You didn't check if you had 2 fuses or 1
All pro have 2 fuse 😁
@@leito9802 oh nice! I want to buy one but it doesn't fit inside my budget 😕
@bare nekid I'm 13 bruh 😂
Why does it not work on 1.6.0
It says [1] sent retry and then it fails
Try multiple times. It should work.
REC Anything still doesn’t work i dont know why.
Same thing here. I tried it multiple times but it won't work.
Did u find any answer ? Also not working here on 1.6.0
same here, does anybody know?
Can you update after usage ? No problem ?
5 months and not a single problem so far...it works like in the 1st day. I noticed that when the battery level goes below 50%, the max speed goes from 30kmph to 26-27 kmph.
@@recanything your m365 is from v1.6.1 than flash using 1.6.0 right ?
12:07 dont upgrade you not need. there will be no magic things only thing you get is anti hack updates lol
for my 1.6.0 = sent retry, sent retry, sent retry, sent retry, sent retry, sent retry, sent retry, sent retry, ...
Try multiple times. It will work. Make sure you have both wifi and gps active on phone. Try restarting the scooter.
@@recanything i have WiFi on what is gps?
@@blurys744 location
ok..😄 I did it 🎇🎆🍻. go to:
th-cam.com/video/nlhz8XJFMYg/w-d-xo.html
I try 10 Times and not working i have location and WiFi on
All ya doing is over heating the battery capacity to get more out put an till the battery blows uo
I have a clone M365 from AliExpress it connects only whit this app called “Youfs”
Can anyone suggest any of those hacks that can help me increasing the speed on my scooter using this app ?
Thank you so much in advance for any useful advices 😎
In the The manual it says “KV986” I believe it’s the model name
When I try to check version it says: asking scooter version. And stays like this. What can I do
Hit the button once again
@@recanything I tried before, but doesn't works.
What version do you have on your scooter? If it's 1.6.6...it's not working. If you have older version, try to restart the scooter and make sure you don't have other app connected to it. Also, activate wifi and location on your phone.
@@recanything men I have the 1.6.6 version😭 With pro model it's possible to downgrade?
Don't know...try searching on the internet...
not work
Doesn’t work for my 1.6.0... „sent retry“
Downgrade to 1.55 ;) I did that from 1.6.2
@@Bushcrawler how?
same for me "sent retry"
I choose russian version of website, it has 1.6 and i have 1.6. but still damn "sent retry"
-.-
?
في عرب 🤡 💔💔
😂😂😂😂😂🙂😭😭😭😭😭
32❌
Dateto✅
(Joke)
0:51 who cares what you will have. you downgrade it LOL.and then its not latest LOL.and come day when you upgrade latest.downgrade not work.until someone hack it again LOL. might be long time if hacer has allreadt what he like LOL