Informative video, thank you. Do you happen to know if you can permanently disable parksense? I put a flat bed on my truck and now parksense errors are abundant!
Also i noticed using the kaodtech bypass cable, the instructions are incorrect. They say to connect the female end to the factory OBD port. My factory OBD port is female.
Sorry to hear this, you will need to contact kaod tech for issues with that harness. You should have one male end that plugs into factory obd port and then the other female end would go in place of factory one on the dash panel
It does have a male connection, just noting that kaodtech instructions are wrong...I hope. I panicked after using it, thought I blew up the computer. Kinda hesitant to try it again. I sent a message to kaodtech, waiting reply.
I have a 2019 ram laramie, recently removed air suspension and now get air suspension warning. Do you have steps on how to delete this? I was using the bypass with alfaobd and had a bad experience. When i tried to start the truck i heard some pops like a fuze blowing. The truck didnt start and eventually the battery went dead. Ever had this happen?
I have not had this experience and cant say I have removed air suspension from any truck, would actually love to have that feature. Have you checked all your fuses?
I did not, may do more on the gas engine equipped trucks more specifically ones equipped with the 5.7 but Im not sure of what it would add to the truck. I never really have had a use or need to change that.
From what it looks like based in the obdlink website they have discontinued the mx, says the LX will do what the mx did but the app developer recommends mx or mx+. Short answer at the moment is possibly but I cant say for sure as I havent used the LX.
@@teedup-81 Did you search cumminsforum under alfaobd success I think is what the thread is called? If it has been done someone on there likely has posted it.
Will this software allow to change settings for transmission type for an auto to manual swap? Basically flash the computer to make it think its a factory manual truck?
Yes and no, it will allow you to change certain parameters within the bcm but will not do anything with your ecm. You will likely need to get a tuner to make these changes for you. If your savvy on tuning recommend you look into Warp tuning and MM3 or Raceme Ultra programmers
Appreciate the video. I have new to me '17 Laramie 2500. Upgraded to 35" tires and don't need 80lb air. Low pressure light bugs me. I'm gonna buy this app. Being it's a '17 I won't need a bypass cable right?
So about the five digit factory code. Will the dealership give that info to the owner? I just bought a new 2022 Laramie 1500 4x4 with lots of ideas for upgrade, but if the dealership will not give the factory 5 digit pin it's all for naught.
I purchased and installed the factory bed lights in my 2015. The instructions said to run the wire to the #5 pin in the block under the dash, which I did. My bed lights go on when my headlights go on. Did I hit the wrong pin #5, or is that how they worked on yours?
@@MKSPerformanceOffroad No. I don't have my lights set to illuminate when I unlock my doors. When I turn my headlight switch on, my bed lights also go on. I suspect I'm in the wrong slot for the cargo light.
I just downloaded this, because I have to prepare my air suspension. One thing I did not see for an option, was saving your configuration, in case you have to revert. If you can point out where this is I'd appreciate it. I am still searching. LoL
There is not a way to physically save your last or original settings. However, you can save a copy of bcm settings to compare to should you need to revert back to those original settings. Hope this helps.
great info...been doing upgrades an using alfaobd past little while...installed overhead console and rear power slider but cant activate the switch...any ideals?
@@MKSPerformanceOffroad thanks for replying .... haven't tried activate anything yet as far as slider goes....not finding anything in obd settings that relate to rear slider... maybe listed differently like the tow mirror puddle lites... activate approach lites...
Any idea what setting to use to turn on the puddle lights on a 2011 ram 3500? I just replaced my mirrors, old ones and new ones have puddle lights but the new ones aren't working. Old ones were burnt up and corroded.
So that was my original question with the app is which setting is it to enable them. I tried the ones I thought it would be. With no luck.. The only difference between my stock mirrors and these is the new ones have the led for signal in the glass as well as on the corner. I didn't know if maybe they took the place of the puddle light.
Great video! Thanks! For a 2019 RAM 1500 Laramie if I use the Android AlfaOBD app and OBD Link MX+ do I also need a security bypass harness that you mentioned or is that only when using Windows? Sorry if I misunderstood. Thank you!
@@MKSPerformanceOffroad Yup. I got the media hub installed and change it to usb+aux. Carplay worked afterwards. Scree switched to black in reverse but just show's black. Camera still works on old uconnect. Head unit may just be bad Anyway thanks for trying to help
KTStull you will need to purchase the paid version to be able to access the truck and features. I think the free version just allows you to look at it and get familiar with it but not perform any functions.
Just ordered everything you suggested for my 22 Ram 2500 hemi,any idea if the entire 12"display has to be removed to plug bypass cable in or can it be accessed without?..& also wondering if mds can be deactivated?..your suggestion is appreciated
I have not had the opportunity to remove the display to find out. Mds is not able to be disabled with alfaobd to my knowledge. Which sgm bypass harness did you purchase?
The security gateway mod is on the left side of the knee bolster cover under the steering wheel. remove the two screws at the bottom then gently pull out it has plastic clips be carefull not to loose them you need to put back.
I purchased the bypass harness from them I have it and the mx+, do you know which to green and white connectors get swapped or do they plug into an empty spot? I did not get any instructions nor can I find any info out there. Thanks
Casey McCormick I will do a video in the next couple days on this specifically but in the mean time, pull the panel under the steering wheel that the obd 2 port is secured to. Unclip the obd port from the panel, clip the harness into that location then connect the bypas harness to the original obd port. If you look directly to the left you will see the CAN Bus block, front side is green and on the backside it is white. Plug the green and white plugs of the bypass harness into any empty slot and your done. Hope this helps.
I found a video that was my saving grace using obd link Mx Bluetooth with alpha obd on my windows 11 laptop. I installed obd wiz software to connect the obd link to alpha obd since the normal windows 11 Bluetooth connection would not work.
Hi thanks for your time. Do you know how I can unlock the speed limit on a Dodge Ram 1500 2020 via Alfa obd? Speed limit is locked on 160 mph. Thanking you all in advance.
Speed limit should be found in the ecm and normally requires a programmer to change. I have not tried to do anything of this sort with Alfaobd. You might look at hp tuners or something of that sort.
Has anyone tried changing the rear doors locks so the doors will open from the inside like a normal vehicle? With the child locks off the rear doors on these trucks won't open as most expect them to.
Depends on which one you are looking for. The kind that Kaod tech makes I have not found anywhere else but have heard others are making, then there is a cable that I have used but requires radio removal to access the sgm.
I have a 1500 ram with factory airride can you change the settings so it would stay in the ride height you select instead of it going into normal ride high after a higher speed?
I'm looking into this option as well. I'd like to install a factory brake controller. Does anyone know if this device needs to be removed if I need to take it in for a factory recall?
It does not need to be removed but you could if you suspect the dealer will hassle you over it. Not hard to remove and I have had no issues with my local dealer yet.
You CAN use AlfaOBD and a bluetooth OBD tool to unlock the brake controller features in your Ram. I just did this today on my RAM 1500 with Mopar brake controller. Enabled 4 options with AlfaOBD now I can set the gain on my dash and see it in my cluster.
Brandon Parsons it is possible with this program. I dont have a video on it but you likely can find instructions if needed here AlfaOBD r.tapatalk.com/shareLink/topic?share_fid=17770&share_tid=123982&url=https%3A%2F%2Fwww%2Eramforum%2Ecom%2Findex%2Ephp%3Fthreads%2FAlfaOBD%2E123982%2F&share_type=t&link_source=app
@mks Perfromance & Offroad, thanks for the video! I have a 22 TRX and ordered Level 2, + most upgrades. However, my dealer accidentally missed Advanced Safety Group when they submitted. All TRX models come with the sensors/electronics needed to add ACC, LKA, and ASG. I've been going back and forth with them for 2 months trying to get them to add the sales codes to my VIN. I give up so I'm going to try it on my own. HAve you completed LKA or ACC on yours? Thnaks!
I have not had to add these features, what is LKA? Looks like 2022 MY has had most options available to enable so I dont See why you couldnt enable the features you want. Thanks for the support.
@MKS Performance & Offroad watching this got me thinking, do you know if it is possible to buy a 2019 auto tailgate install in on a 14 and activate that?
Yes most definitely. Head over to an alfaobd thread like on the ramz forum or cummins forum and there are posts there that list components you will need. If you need a link just let me know. Most popular one is alfaobd success.
I just answered this same question on another video you posted the comment on. Alfaobd is a very capable tool but it is still limited in things it can perform. I have not replaced a win module on anything older like that but I know people have done it on newer 4th gen Ram trucks. I would assume there is a pin you need to get as well which you may be able to pull with alfaobd. Give it a try.
Dan the Man try going into bcm, cbc features, passive entry. Also, check out this thread www.ramforum.com/threads/how-to-add-factory-keyless-enter-n-go.134961/. That should have all the info you could want about adding it if there is something you dont have and need to add.
airell47 I havent personally used it on anything older than 2013, however, did a little google search and there are quite a few people who confirmed it works on 2006+ as these were the beginning years with CAN bus systems. Look at igotacummins.com, cumminsforum.com, and ramzforum.com.
Hey man, I have an 18 2500 g56. Curious if you could give me some insight on how to do the remote start? If I have to physically bypass the clutch or if it is in the programming? I have the new keys and will be attempting to perform this all in the coming week.
You will need to bypass the clutch which will allow the truck to start in gear and lurch forward. I looked into doing this a while ago and decided not to for safety. I personally havent attempted this so I would look at the cummins forum under alfaobd g56 remote start.
Trying to change odometer on my 2017 ram upgraded cluster from 3" to 7" , so far unsuccessful, did many attempts keeps saying procedures failure, any suggestions on why? Any help would be appreciated
@@MKSPerformanceOffroad well kinda I did the 3.5 like you suggested I went from 200,000 km to 129,000 km I didn't do the mileages conversion, where I wanted to be is 80,400 km I've tried again nothing changes any idea why it won't let change it
Sorry this is comment is about 3 years too late. When I went to the kaodtech website, the module was out of stock as well. I put in my email to be notified of when it would be in stock, and got an email the same day notifying me it was available to purchase. I'm pretty sure they are made to order.
This is only accomplished through an android or windows os. Unfortunately there isn’t anything to my knowledge utilizing ios to make changes to configurations.
Jacob Gawrys it is possible that the dealer could give you some grief if you were the cause of a self induced problem which required the dealer to reflash the ecm or bcm. Generally though, if your careful and only adjust things that are known to work like what I show in the videos they have no issue. Guys get in trouble when they dont follow step by step and freak out when something isnt expected. I do remove the bypass harness when I go to the dealer. The tool is very powerful but as long as you are careful it should not void any warranty for general adjustments (activating lights, calibrating speedo, changing splash screens etc). Hope this answers your question
MKS Performance & Offroad , Thank you for the quick response. I’m just looking to do simple things, Global Down for the front 2 windows and recalibrate the tire size. Thanks Again!!!
Alfaobd will not turn on the mirror turn signals as markers. The only way Im tracking is to buy a kit and run the wires through the door to make them come on as DRLs.
The 8.4a is nav ready but you need a tool that can pull the pin from the radio that is specific to the radio which most likely has to be done at the dealer. They charge somewhere between $5-600 to do this. Most of this is locked due to proprietary software.
@@MKSPerformanceOffroad I'm pretty sure there's an android based PIN tool I've used in the past. They exist but may not work on all builds. _____________________________________ carkeyst.com/ The CHRYSLER PIN PULLER is the cheapest, reliable and easy to use tool on today's market!Designed to pull pin codes from Chrysler, Jeep, Dodge, Ram and some Fiats, Maserati, vehicles! All major models are supported from 2005 - 2014(16). Pulls PIN out of vehicle through OBD via an ELM327 Bluetooth compatible adapter.
AN yes this tool Ive heard works, however, the pin is yours and should be provided to you at no charge. Dealerships that hassle for this are dealers I’d never go back to or recommend. If this is the last resort though then its another option.
Tyler Maloney yes I can, super simple to install as everything is in close proximity. I will show this in one of the upcoming videos involving wiring my isspro back pressure gauge.
Audio Expertz you can do diagnostics and clear codes with this software, I cant say whether it will do every code but I can tell you it will clear everything I’ve experienced so far. Are there specific ones you want to know about?
Hey man have you noticed there is a selection in AlfaOBD to disable the scr/def. I’m scared to hit it and see what happens. Curious if you could select that and get rid of def 🤣🤣
gun freak I’m aware of it but haven’t tried it. This may be an option in the ECM for chassis like Ambulances or emergency vehicles that wouldn’t use that system, however, along with that you would need the correct engine calibration to go with it. There are many things in Alfaobd that can be manipulated (turned on or off) but could cause unanticipated effects without the correct settings or equipment present. This is one of those things you have to take caution on and just make note of the change and compare to your module backups to see if it changes anything else. Hope this helps answer your question. It also may not do anything and just show as an option.
Thanks for the video 👍 I just received my ODBlink MX+ and bought the AlfaODB software. I ll try to activate automatic windows rolling and DRL’s on my 2017 Laramie. Your video will be helpful. Thanks Kind regards from France.
@@MKSPerformanceOffroad Front Fog with high beams >> works Global windows down >> works Global windows up >> doesn't work ( as for you ) Next time I'll play with DRL's ;)
Rust 4Ever global up is not able to be activated in the bcm for one reason or another. You may want to look at a taser unit which from what I read allows this feature. They are pricey though.
@@rustntrucks Up feature - nobody wants the liability of the "could happens" when little Timmy didn't get his head out of the window in time. Lil Timmy knew that the windows wouldn't go up or down since the keys were not in the ignition. He also didn't know that there was a new override feature that allowed them to roll up.
Checking your page out. Your dad delivered here N.O.A.A. (Grandview, MO)today 15Aug19. Told me to check you out. I have a 2014 dodge ram 2500 crew cab longbed 4x4 diesel 6.7L
Thanks for checking the channel out! Ill be uploading more content on a weekly basis. Focus right now is alfaobd, tuning, misc., and whatever else anyone requests we will try our best to accomodate.
I have never heard so many ”Um’s” in my life. Great videos but I just can unhear all the um’s you say. Very annoying. Maby something to take in mind for futur videos.
I think Im leaning more towards a paint match on these with black badging or potentially no badging. I didnt like the way the black looked when it was rendered.
I like my factory options I want to enable. Setting this truck up the way I wanted it and adding my touches. Nothing wrong with that, everyone likes there truck a certain way and this truck is turning out great.
Also i noticed using the kaodtech bypass cable, the instructions are incorrect. They say to connect the female end to the factory OBD port. My factory OBD port is female.
Informative video, thank you. Do you happen to know if you can permanently disable parksense? I put a flat bed on my truck and now parksense errors are abundant!
@@Torrakify should be able to disable them.
Thank you!
Also i noticed using the kaodtech bypass cable, the instructions are incorrect. They say to connect the female end to the factory OBD port. My factory OBD port is female.
Sorry to hear this, you will need to contact kaod tech for issues with that harness. You should have one male end that plugs into factory obd port and then the other female end would go in place of factory one on the dash panel
It does have a male connection, just noting that kaodtech instructions are wrong...I hope. I panicked after using it, thought I blew up the computer. Kinda hesitant to try it again. I sent a message to kaodtech, waiting reply.
I have a 2019 ram laramie, recently removed air suspension and now get air suspension warning. Do you have steps on how to delete this? I was using the bypass with alfaobd and had a bad experience. When i tried to start the truck i heard some pops like a fuze blowing. The truck didnt start and eventually the battery went dead. Ever had this happen?
I have not had this experience and cant say I have removed air suspension from any truck, would actually love to have that feature. Have you checked all your fuses?
I know this was 3 years ago, but by chance did you ever look under "sport Mode" and see what that did?
I did not, may do more on the gas engine equipped trucks more specifically ones equipped with the 5.7 but Im not sure of what it would add to the truck. I never really have had a use or need to change that.
Have you tried the sport mode change?
@@louistrainersr6581 I have not yet.
Will the obdlink LX do all the features as the mx. What is the difference. Besides the price tag. Thanks
From what it looks like based in the obdlink website they have discontinued the mx, says the LX will do what the mx did but the app developer recommends mx or mx+. Short answer at the moment is possibly but I cant say for sure as I havent used the LX.
Obd link LX will work, someone just posted it on the forum confirming
Is there a way to make it so the cargo lamps come on when door is opened?
Id have to look in Alfaobd but this is t something I have done or seen done.
@@MKSPerformanceOffroad I tried looking as well but didn’t see anything that jumped out at me…
@@teedup-81 Did you search cumminsforum under alfaobd success I think is what the thread is called? If it has been done someone on there likely has posted it.
@@MKSPerformanceOffroad I did not. Didn’t even think about it as I have a half ton gasser. I will tho!!!
@@teedup-81 in that case, check there and I think ramforumz.com
Will this software allow to change settings for transmission type for an auto to manual swap? Basically flash the computer to make it think its a factory manual truck?
Yes and no, it will allow you to change certain parameters within the bcm but will not do anything with your ecm. You will likely need to get a tuner to make these changes for you. If your savvy on tuning recommend you look into Warp tuning and MM3 or Raceme Ultra programmers
Appreciate the video. I have new to me '17 Laramie 2500. Upgraded to 35" tires and don't need 80lb air. Low pressure light bugs me. I'm gonna buy this app. Being it's a '17 I won't need a bypass cable right?
You shouldnt need it for pre 2018 trucks
You shouldnt need the bypass
I have Bluedriver OBD2, will it work?
I tried it and it will not work
Do i have to get a code from dealership for all this modifications or thats is just for the tire pressure?
@@toleratedgonur7174 you should only need the code for specific procedures like resetting of hub or programming keys.
Can I put heated seats in mine and add the bottoms to my UConnect on my radio? I drive a 15 Ram Big Horn 2500.
Yes you should be able to do both of those as long as the required hardware is installed for the circuit to function.
The windows global down/up option is this available on 2022 2500 RAM
I can't say 100% as I haven't worked on anything newer than 2019 personally. I haven't heard that it wasn't an available option to enable though.
So about the five digit factory code. Will the dealership give that info to the owner? I just bought a new 2022 Laramie 1500 4x4 with lots of ideas for upgrade, but if the dealership will not give the factory 5 digit pin it's all for naught.
They should give it out no issues. Just have to bring in your registration and an ID.
I have a Chrysler 300c 2012, How do I find out what version my body computer is?
Why do people want the windows to roll down with the fob? Never got the use case for that
Hot summers, cool down before getting in. Common program with vw vehicles as well.
What do I need to do to my truck to get that loud turbo whistle on startup like yours has in the intro?
Cold start with exhaust brake on
I have a 2012 ram 1500 will this work and if not what software/programmer I have to get for me to do this to my truck
It should work as long as its an option in your MY BCM
I purchased and installed the factory bed lights in my 2015. The instructions said to run the wire to the #5 pin in the block under the dash, which I did. My bed lights go on when my headlights go on. Did I hit the wrong pin #5, or is that how they worked on yours?
Chris Happ when you unlock doors?
@@MKSPerformanceOffroad No. I don't have my lights set to illuminate when I unlock my doors. When I turn my headlight switch on, my bed lights also go on. I suspect I'm in the wrong slot for the cargo light.
Chris Happ sounds like it. They should come on when vehicle unlocks.
On a 2018 do I need the bypass if mopar gives me the security key?
Yes unless you can push programming through the sgm. Normally this needs to be done by way of J2534 pass thru
does it work on aftermarket parking sensors ?
Yes as long as you are programming to a factory system.
I just downloaded this, because I have to prepare my air suspension. One thing I did not see for an option, was saving your configuration, in case you have to revert. If you can point out where this is I'd appreciate it. I am still searching. LoL
There is not a way to physically save your last or original settings. However, you can save a copy of bcm settings to compare to should you need to revert back to those original settings. Hope this helps.
@@MKSPerformanceOffroad thank you. It's weird because I always hear people talking about saving your configuration.
@@m3rdpwr yes that is your bcm config which is a text file that shows what is our isnt enabled.
I'm guessing that it doesn't matter if gas or diesel when it comes to changing things?
You are correct sir
Can you do all these with the Laptop Adapter and laptop version of ALPHAobd? I’m guessing so but haven’t seen that question posed.
Yes, I do both and explain it in one of my other videos
great info...been doing upgrades an using alfaobd past little while...installed overhead console and rear power slider but cant activate the switch...any ideals?
Thanks, Please post settings you have activated so far, there might be one missing or it may take it a bit to set in the bcm.
@@MKSPerformanceOffroad thanks for replying .... haven't tried activate anything yet as far as slider goes....not finding anything in obd settings that relate to rear slider... maybe listed differently like the tow mirror puddle lites... activate approach lites...
@@MKSPerformanceOffroad as far as the upper console I have activated the homelink and compass features
@@ronaldvezina1323 have you tried the search feature in the program?
Any idea what setting to use to turn on the puddle lights on a 2011 ram 3500? I just replaced my mirrors, old ones and new ones have puddle lights but the new ones aren't working. Old ones were burnt up and corroded.
If they were originally enabled they should work when new ones are installed. Are you sure you have a good connection and power to the new mirrors?
Did you get your puddle lights working?
No I did not. I need to test connectivity with a volt meter. Just have been busy the past few weeks.
Brandon Barber and you have the mirror lets enabled already for sure in bcm?
So that was my original question with the app is which setting is it to enable them. I tried the ones I thought it would be. With no luck.. The only difference between my stock mirrors and these is the new ones have the led for signal in the glass as well as on the corner. I didn't know if maybe they took the place of the puddle light.
Is there a way i can program my mirrors to close when i lock my doors ram 1500 2017
chris see unfortunately I dont believe that is an available option to program.
@@MKSPerformanceOffroad It is, I just cant remember where it is.
Great video! Thanks! For a 2019 RAM 1500 Laramie if I use the Android AlfaOBD app and OBD Link MX+ do I also need a security bypass harness that you mentioned or is that only when using Windows? Sorry if I misunderstood. Thank you!
2018+ will need the bypass cable.
I have a 2014 big horn. Tried to put a 2018 8.4 uconnect in it. Got everything to work except backup camera and steering wheel controls. Any help?
Do you have them enabled via alfaobd correctly and appropriate components installed?
@@MKSPerformanceOffroad yes they’re enable. What components?
@@gleem1751 I believe with upgraded radio the media hub is required for it to function correctly
@@MKSPerformanceOffroad Yup. I got the media hub installed and change it to usb+aux. Carplay worked afterwards. Scree switched to black in reverse but just show's black. Camera still works on old uconnect. Head unit may just be bad Anyway thanks for trying to help
obdlink mx work as well as the plus?
If Im not mistaken the plus is a little bit faster as far as communication, both will work well though
Hello. Does it work with elm327 on RAM's?
Yes, see www.alfaobd.com/
Can you use the free version of Alfaobd or do you need to use the paid version?
KTStull you will need to purchase the paid version to be able to access the truck and features. I think the free version just allows you to look at it and get familiar with it but not perform any functions.
Just ordered everything you suggested for my 22 Ram 2500 hemi,any idea if the entire 12"display has to be removed to plug bypass cable in or can it be accessed without?..& also wondering if mds can be deactivated?..your suggestion is appreciated
I have not had the opportunity to remove the display to find out. Mds is not able to be disabled with alfaobd to my knowledge. Which sgm bypass harness did you purchase?
I ordered cable from kaodtech that you suggested
The security gateway mod is on the left side of the knee bolster cover under the steering wheel. remove the two screws at the bottom then gently pull out it has plastic clips be carefull not to loose them you need to put back.
Does the alfaobd have the option to add the offroad pages to a 2018 ram power wagon?
I cant say 100% but I do remember seeing them. I personally havent done this so cant say for sure what all it will enable in regards to that
Can you disable drl? Or change it from headlight to corner marker?
Yes you should be able to change drl locations in alfaobd
I purchased the bypass harness from them I have it and the mx+, do you know which to green and white connectors get swapped or do they plug into an empty spot? I did not get any instructions nor can I find any info out there. Thanks
Casey McCormick I will do a video in the next couple days on this specifically but in the mean time, pull the panel under the steering wheel that the obd 2 port is secured to. Unclip the obd port from the panel, clip the harness into that location then connect the bypas harness to the original obd port. If you look directly to the left you will see the CAN Bus block, front side is green and on the backside it is white. Plug the green and white plugs of the bypass harness into any empty slot and your done. Hope this helps.
I made a short one....really short but hopefully it helps th-cam.com/video/A54WKP5elz0/w-d-xo.html
Can you use this device to program additional key fobs?
Yes
Can I change factory options using the Autel 12+8 adapter or do I need the Kaodtech?
12+8 will work just a little more involved
@@MKSPerformanceOffroad
Do you have a video available using the 12+8?
I found a video that was my saving grace using obd link Mx Bluetooth with alpha obd on my windows 11 laptop. I installed obd wiz software to connect the obd link to alpha obd since the normal windows 11 Bluetooth connection would not work.
Can you force fog lights to stay on with high beams?
Yes you can absolutely enable that feature. You want to disable fog light drop out
@@MKSPerformanceOffroad just did it right now. Thanks man super bright on the rebel now 👍
Hi thanks for your time.
Do you know how I can unlock the speed limit on a Dodge Ram 1500 2020 via Alfa obd?
Speed limit is locked on 160 mph.
Thanking you all in advance.
Speed limit should be found in the ecm and normally requires a programmer to change. I have not tried to do anything of this sort with Alfaobd. You might look at hp tuners or something of that sort.
@@MKSPerformanceOffroad I'll be appreciated if you could find some thing even in Hptuner.
I can get it.
Has anyone tried changing the rear doors locks so the doors will open from the inside like a normal vehicle? With the child locks off the rear doors on these trucks won't open as most expect them to.
With child locks off your rear doors should open just as the fronts do with no issue.
Is there anywhere else other then kaodtech to get this bypass?
Depends on which one you are looking for. The kind that Kaod tech makes I have not found anywhere else but have heard others are making, then there is a cable that I have used but requires radio removal to access the sgm.
can i do a remote start on a 16 ram that didnt come with it?
Yes, you should be able to add it.
What all do you need to do it? Just the fob?
I have a 1500 ram with factory airride can you change the settings so it would stay in the ride height you select instead of it going into normal ride high after a higher speed?
I added tow mirrors to my 2018 ram 2500. Would this work to make the turn signal and puddle lights work?
Ricky P yes most definitely
I'm looking into this option as well. I'd like to install a factory brake controller. Does anyone know if this device needs to be removed if I need to take it in for a factory recall?
It does not need to be removed but you could if you suspect the dealer will hassle you over it. Not hard to remove and I have had no issues with my local dealer yet.
Why don’t the back windows roll down too?
The global down feature only applies to the front windows, not sure why they didn’t design it to do all.
That’s disappointing. Still gonna have to pick up an android tab(team iPhone😂) and get alfaobd. This is a neat addition.
@@tylercampfield9818 it is fun to play with and very capable.
What kind of tablet did you use
Lenovo tab 10
If I install a factory trailer brake controller, can you use this program to activate it? Or do I still have to take it to the dealership?
You should be able to use the program to activate it.
You CAN use AlfaOBD and a bluetooth OBD tool to unlock the brake controller features in your Ram. I just did this today on my RAM 1500 with Mopar brake controller. Enabled 4 options with AlfaOBD now I can set the gain on my dash and see it in my cluster.
I want to turn my drls that are my brights off or make them my park lamps
Brandon Parsons it is possible with this program. I dont have a video on it but you likely can find instructions if needed here AlfaOBD
r.tapatalk.com/shareLink/topic?share_fid=17770&share_tid=123982&url=https%3A%2F%2Fwww%2Eramforum%2Ecom%2Findex%2Ephp%3Fthreads%2FAlfaOBD%2E123982%2F&share_type=t&link_source=app
@mks Perfromance & Offroad, thanks for the video! I have a 22 TRX and ordered Level 2, + most upgrades. However, my dealer accidentally missed Advanced Safety Group when they submitted. All TRX models come with the sensors/electronics needed to add ACC, LKA, and ASG. I've been going back and forth with them for 2 months trying to get them to add the sales codes to my VIN. I give up so I'm going to try it on my own. HAve you completed LKA or ACC on yours? Thnaks!
I have not had to add these features, what is LKA? Looks like 2022 MY has had most options available to enable so I dont See why you couldnt enable the features you want. Thanks for the support.
@MKS Performance & Offroad watching this got me thinking, do you know if it is possible to buy a 2019 auto tailgate install in on a 14 and activate that?
The only way you would be able to is if that were an option offered on a 2014 which I dont think it was. It has to be present in the bcm to enable it.
Were did you get the leather done
Leather is katzkin leather covers that I had the dealer install when I bought the truck
Can I use this program to make my truck remote start off key fob. 2013 ram express
Yes most definitely. Head over to an alfaobd thread like on the ramz forum or cummins forum and there are posts there that list components you will need. If you need a link just let me know. Most popular one is alfaobd success.
@@MKSPerformanceOffroad I have looked for a site for this info but can't find it, do you have it handy?
Can I program win module?
I just answered this same question on another video you posted the comment on. Alfaobd is a very capable tool but it is still limited in things it can perform. I have not replaced a win module on anything older like that but I know people have done it on newer 4th gen Ram trucks. I would assume there is a pin you need to get as well which you may be able to pull with alfaobd. Give it a try.
Apologies if asked already but was that stock or aftermarket leather?
It is katzkin covers that were installed when purchased and we got them through mopar so they have the factory mopar tag on them
@@MKSPerformanceOffroad they look great and are exactly what I was thinking when I do leather interior on my 2010 2500 diesel. Thanks!
Very cool and interesting. Does the AlfaOBD work with a 2009 Laramie?
yes it does!
Great video.
1. You have a link for alphaOBD app?
2. Did you ever figure out the window up option?
Window up does not work and if you search play store for alfaobd it will show up
Where would I go to add the gxm or keyless entry ability to an st with power locks?
Dan the Man do you have all the parts needed and have you checked out the procedure for it all on forums?
@@MKSPerformanceOffroad yes, I have the software and obd I'm just not sure where to go to find that option
Dan the Man try going into bcm, cbc features, passive entry. Also, check out this thread www.ramforum.com/threads/how-to-add-factory-keyless-enter-n-go.134961/. That should have all the info you could want about adding it if there is something you dont have and need to add.
Correction, try going to bcm, 2013-17 powernet, config change, vehconfig3, passive entry
I have a 2011, is it the rke option?
will that allow me to turn on factiory back up camera on the u connect radio ?
Yes depending on year and radio model.
I only own apple devices, am i just outta luck?
You can try Jscan. I have heard it works but never personally used it
can you use a android phone with app ?
Yes absolutely.
@@MKSPerformanceOffroad awesome
does this app / link work on the 2007 model rams
airell47 I havent personally used it on anything older than 2013, however, did a little google search and there are quite a few people who confirmed it works on 2006+ as these were the beginning years with CAN bus systems. Look at igotacummins.com, cumminsforum.com, and ramzforum.com.
Hey man,
I have an 18 2500 g56. Curious if you could give me some insight on how to do the remote start? If I have to physically bypass the clutch or if it is in the programming? I have the new keys and will be attempting to perform this all in the coming week.
You will need to bypass the clutch which will allow the truck to start in gear and lurch forward. I looked into doing this a while ago and decided not to for safety. I personally havent attempted this so I would look at the cummins forum under alfaobd g56 remote start.
Trying to change odometer on my 2017 ram upgraded cluster from 3" to 7" , so far unsuccessful, did many attempts keeps saying procedures failure, any suggestions on why? Any help would be appreciated
Try changing the odometer under the 3.5”
Did you get it?
@@MKSPerformanceOffroad well kinda I did the 3.5 like you suggested I went from 200,000 km to 129,000 km I didn't do the mileages conversion, where I wanted to be is 80,400 km I've tried again nothing changes any idea why it won't let change it
@@nicknay4118 is it giving you any error messages? Or it just wont take the mileage?
@@nicknay4118 try programming it in ACC rather than run, program in 3.5 option and hope that helps you out
Great video, thanks. Soooo...like everything else in the world we live in these days, cable is out of stock. Can I rent yours 😆
Sorry, I don’t rent the cable out. If you go on cummins forum you may find someone in your area local that has one to borrow or perform the changes.
@@MKSPerformanceOffroad hahaha, to funny. That's actually a great 💡 I will check that out
Sorry this is comment is about 3 years too late. When I went to the kaodtech website, the module was out of stock as well. I put in my email to be notified of when it would be in stock, and got an email the same day notifying me it was available to purchase. I'm pretty sure they are made to order.
For ios what app can i use
This is only accomplished through an android or windows os. Unfortunately there isn’t anything to my knowledge utilizing ios to make changes to configurations.
Thank you for the video. I’m sure this has been asked, but does this void any kind of warranty you may have on the truck?
Jacob Gawrys it is possible that the dealer could give you some grief if you were the cause of a self induced problem which required the dealer to reflash the ecm or bcm. Generally though, if your careful and only adjust things that are known to work like what I show in the videos they have no issue. Guys get in trouble when they dont follow step by step and freak out when something isnt expected. I do remove the bypass harness when I go to the dealer. The tool is very powerful but as long as you are careful it should not void any warranty for general adjustments (activating lights, calibrating speedo, changing splash screens etc). Hope this answers your question
MKS Performance & Offroad , Thank you for the quick response. I’m just looking to do simple things, Global Down for the front 2 windows and recalibrate the tire size. Thanks Again!!!
My RAM's cargo light doesn't turn on when I open the tailgate. Is that something i can use this app to enable?
Normal operation it should turn on with the button on dash or unlock on key fob. Does it do those functions?
@@MKSPerformanceOffroad it does do that, but im looking to make it turn on when the tailgate is opened
Your thinkpad cover seems to be having the same issues as your other truck 😂😂
can this be used on RAM 2019
Chris Thelen should work as I have heard many people using it on a 2019.
Great video Can you show us how to turn mirror lights on as markers?
Alfaobd will not turn on the mirror turn signals as markers. The only way Im tracking is to buy a kit and run the wires through the door to make them come on as DRLs.
Can you unlock navigation for the 8.4" screen. Or do you have to buy that specific radio
The 8.4a is nav ready but you need a tool that can pull the pin from the radio that is specific to the radio which most likely has to be done at the dealer. They charge somewhere between $5-600 to do this. Most of this is locked due to proprietary software.
@@MKSPerformanceOffroad I'm pretty sure there's an android based PIN tool I've used in the past. They exist but may not work on all builds.
_____________________________________
carkeyst.com/
The CHRYSLER PIN PULLER is the cheapest, reliable and easy to use tool on today's market!Designed to pull pin codes from Chrysler, Jeep, Dodge, Ram and some Fiats, Maserati, vehicles!
All major models are supported from 2005 - 2014(16).
Pulls PIN out of vehicle through OBD via an ELM327 Bluetooth compatible adapter.
AN yes this tool Ive heard works, however, the pin is yours and should be provided to you at no charge. Dealerships that hassle for this are dealers I’d never go back to or recommend. If this is the last resort though then its another option.
Great video! The only thing that could be better is your mic. Cheers
I need to get one soon.
What were some of the issues you had with the 14 Laramie?
Mold in the rear can under seats and made its way into the blower and air ducts.
Can you do a video for the by pass? It's the only thing I'm struggling with. Lol
Tyler Maloney yes I can, super simple to install as everything is in close proximity. I will show this in one of the upcoming videos involving wiring my isspro back pressure gauge.
th-cam.com/video/A54WKP5elz0/w-d-xo.html
hi , dodge ram 1500 5.7 ,2009 motor DS
Can this remove pcm codes
Audio Expertz you can do diagnostics and clear codes with this software, I cant say whether it will do every code but I can tell you it will clear everything I’ve experienced so far. Are there specific ones you want to know about?
@@MKSPerformanceOffroad well after the pcm got flash back to stock o2 sensor and battery voltage is on
Hey man have you noticed there is a selection in AlfaOBD to disable the scr/def. I’m scared to hit it and see what happens. Curious if you could select that and get rid of def 🤣🤣
gun freak I’m aware of it but haven’t tried it. This may be an option in the ECM for chassis like Ambulances or emergency vehicles that wouldn’t use that system, however, along with that you would need the correct engine calibration to go with it. There are many things in Alfaobd that can be manipulated (turned on or off) but could cause unanticipated effects without the correct settings or equipment present. This is one of those things you have to take caution on and just make note of the change and compare to your module backups to see if it changes anything else. Hope this helps answer your question. It also may not do anything and just show as an option.
Thanks for the video 👍
I just received my ODBlink MX+ and bought the AlfaODB software.
I ll try to activate automatic windows rolling and DRL’s on my 2017 Laramie.
Your video will be helpful. Thanks
Kind regards from France.
Awesome, glad it was helpful. Stay tuned, Ill be adding individual videos for each procedure. Thanks for subscribing, enjoy that Laramie!
@@MKSPerformanceOffroad
Front Fog with high beams >> works
Global windows down >> works
Global windows up >> doesn't work ( as for you )
Next time I'll play with DRL's ;)
Rust 4Ever global up is not able to be activated in the bcm for one reason or another. You may want to look at a taser unit which from what I read allows this feature. They are pricey though.
@@rustntrucks Up feature - nobody wants the liability of the "could happens" when little Timmy didn't get his head out of the window in time. Lil Timmy knew that the windows wouldn't go up or down since the keys were not in the ignition. He also didn't know that there was a new override feature that allowed them to roll up.
How do I buy this unit??
amzn.to/3ioHkcT
Checking your page out. Your dad delivered here N.O.A.A. (Grandview, MO)today 15Aug19. Told me to check you out. I have a 2014 dodge ram 2500 crew cab longbed 4x4 diesel 6.7L
Thanks for checking the channel out! Ill be uploading more content on a weekly basis. Focus right now is alfaobd, tuning, misc., and whatever else anyone requests we will try our best to accomodate.
IS THAT A MANUAL RAM!?!?
It most definitely is.
@@MKSPerformanceOffroad its beautiful
Can't hear anything
Probably the settings on the device your using to view. Sound works on my end when I play it.
@@MKSPerformanceOffroad sounds is all the way up on my device and it sounds like you ate whispering
I have never heard so many ”Um’s” in my life. Great videos but I just can unhear all the um’s you say. Very annoying. Maby something to take in mind for futur videos.
Gross don't black out grille and bumper it will look terrible
I think Im leaning more towards a paint match on these with black badging or potentially no badging. I didnt like the way the black looked when it was rendered.
leave it stock!
I like my factory options I want to enable. Setting this truck up the way I wanted it and adding my touches. Nothing wrong with that, everyone likes there truck a certain way and this truck is turning out great.
Kenneth Plunkett leave your own truck stock.
@@RL-pj8tj mine is stock and it runs just fine.
Also i noticed using the kaodtech bypass cable, the instructions are incorrect. They say to connect the female end to the factory OBD port. My factory OBD port is female.