1967 Porsche 911 Video 38 Installing Tunnel Lines
ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- In this Video we will be setting up the first components to the shell
Beginning with tunnel lines, cables and wiring harness
Welcome to our new Super Store!
www.amazon.com...
#porsche #porscherestoartion #porsche911 #restoration
Beautiful work.
Thanks Dan!
Love the attention to detail. Good job.
Thanks Goose!
Another great video Mike! I’m resisting the temptation to jump forward in the series of videos...
Hello Tom thanks
Go for it! you can always look back and see the progress.
A new one coming this weekend!
Cheers and keep safe!!
Beautiful Mike; the car is an absolute credit to you and your workmanship.
Thanks Brett
Slow and steady..I think anyone can do it=)
Thank you so much for making this series! It has been an inspiration to repair, maintain and restore my '68 912. Although I'm light years from your skills and knowledge, it has been an invaluable source of detailed step by step procedures not found anywhere else. Thanks and greetings from Chile!
Hello Javier
Wow! Chile!! It’s been a pleasure sharing this special car. I’m so glad the series is helpful and hopeful get some of those older Porsches back in running order😀
I wish you the best of luck on your restoration and thank you for the kind words
Cheers!
Those before and after shots...amazing.
Hey Patric
Yes its crazy one can come from the other
Ciao Mike (from Italy), what a piece of art! Your attention up to the tiniest detail is so inspiring! I can't wait for your next video...
Hi Giovanni
Thank you for the sincere compliment =)
Next one in the works!
Fantastic. Shrink wrap I wish I had thought of that!
Hi Gary
That tunnel can get crowed for sure!
Hey Mike, the tunnel is very tricky. I know a lot of guys that have done fuel lines insitu! I rewired my whole front end. I used network cable sheathing to keep it all together while routing it. Green shrink wrap would be much better because it's already a little slick. You're going to have a better than new 911 in the end. Keep up the great work; you're a real artist.
amazing transformation!
Thanks Greg! Its finally coming together
I love this car!!!
Hey Mooney
Yes me too=)!
Another great video Mike, the car is stunning and as I work on my 66, this is a great reference!
This hopefully will be a good source to draw from for the earl cars
Manuals are nice but video sure makes it easier
Mike M - question for you where did you source your heater orange silicone hoses?
Hello matlecomte
They are Porsche genuine..material is a fiberglass fabric with dye color coating
They are quite ridged compared to the original which had more wire winding for bending.
I think the silicon after market type might be a good option for flexibility although I have not seen
those up close.
Good luck!
Thank you for the video. Every time, I am amazed by the attention to the detail. Probably the best restoration project I ever followed :-)
Hi Youssef
Thank you for the nice comment and you are very welcome=)
Hopefully might be of some use for you someday
Thanks Mike, really helpful video. Especially as my car came to me already striped down. Your car looks fantastic as usual.
Hi Andrew Thanks Im glad it can be of good use..Should help to makes sense of thing especially if you don't have enough teardown pictures
Good luck on your resto!
Fantastic
Thanks John!
Big steps Mike! Getting there :)
Hey Feeesh!
Yes she's on the way!
Shows me just how little I know. Thx.
Hi Jeff
I think you know more than you might realize
I didn't know much about Porsche before starting this project
Great stuff as usual!
Thanks John
She's finally coming together
Nice work and thanks
You're Welcome Steve!
Your videos are as outstanding as helpful. Thanks a lot Mike, you are my restoration hero! Regards from Fredrik Klass, a proud Porsche 912 from 1966 owner.
p.s. your restorated Porsche will be more well made than it ever was as newly produced from factory. Ever want to sell it?
Thanks fredrik I really appreciate your enthusiasm.
These old classic Porsches are such awesome cars..
As for selling it..its not really something I entertain maybe someday when I'm old and running out of steam or not able to drive anymore. Although If I wasn't able to drive anymore it would still look nice in my living room as a conversation piece=)
@@MikesRestorations Thought so :-) Have you seen my question regarding fuel gauge red light?
Hello Mike, thank you so much for your excellent videos. They have been invaluable for me during my restoration process of a 65 912. A question: Is the speedometer cable and brake line held by the same hold-down tabs? I am a bit confused atm :-)
Hello Palo Alto Thank you im glad they can be of some help.
I have reviewed the video footage and also gone back through some photos and as best I can see
and they do share the same hold down tabs near the hand brake location.
Most of the lines as they run through the tunnel kind of settle in to what needs to happen.
Also cars may be different on what's available through the tunnel.
One other point I should bring up after reviewing the video is the accelerator rod that runs down the tunnel
does get bushings installed the holding tabs.
I show them in another video but don't recall off hand which one that was.
My car did not have them but they were a factory installed items. A viewer brought to my attention!
Good luck!
@@MikesRestorations, thank you so much for the detailed response!
Hi Mike, I'm watching every video with great interest. Trying to get all the details. Did I miss a video of the general wiring harness of this fine automobile? I can see you have some wiring harness going on in the engine bay with the next video, but I can already see some wires (and heat tubes) in this video. What did I miss? I hate to miss some of your detailed work. They way you work is a great inspiration, for all restoration projects thanks
Hello Thomas
Thank you=) yes there are several harnesses on the car I will be going over in greater detail. In Video 38 it was just pulling the main harness into location but not much for hookups as of yet.
There is also a harness in the headliner installation video definitely
worth checking out. The headliner harness is tough!!!
As the series continues I will cover all hookups..little bits are revealed during ongoing segments as the timing require.
Lots of video to watch but I hope not to have to many gray areas..
If you have a any particular question I will try my best to answer
Feel free to reach out!
great to see your 901 again in the Vegas sun Please can you tell us people what's goin' on with the Motor and trans'? great work Mike can't wait for the next :))
Hi Richard
Motor and trans will be last work done on the restoration.
Detailed video will be on on those components too but will be last in the series
Hi Mike - I really got a lot out of this video since I'm repairing and reinstalling my heater valves, hoses and cables. As usual, beautiful work. I have been looking for where to buy the heater hose clamps as shown in the video at 11:01. The part number I have is 901.211.051.22 but what shows up is another style (with the pipe welded to the side of the clamp), not like the ones you have. Would you have a suggestion as to where to buy them? Thanks.
Hello Rotarybreather thank you
The clamps you are referring to in the video are factory originals from 1966 refinished.
When Porsche remanufactures some parts they make small changes to be more suitable for a wider range of years and models.
Im sure the new clamp style would work but if you are looking for these parts exactly I would recommend searching eBay for some
used originals.
Most of my Genuine Porsche Parts are sourced here
www.porschesandiegoparts.com/oem-parts/porsche-pipe-clamp-90121105122
Always affordable and always beautifully packaged and shipped usually within one week. A great place to source all your Genuine
parts. Sometimes they don't have pictures when you enter your part number but as long as you are sure its the correct part number
they will ship correctly. Also I think for those clamps there would be a left and a right ..Its been a while since working with them
Good luck!
Mike - do you have a video showing how to hook up the cables to the heat exchangers (that open the flapper boxes, not the heater valves)?
Hi Mike, how did you clean the wiring insulation? I tried white spirit but it washed the color stripe from the wire.
Hello Ian
The wire harness was washed with warm soapy water and paint gently scrubbed with paint brush..followed by clean water rinse.
Next Blow dried with compressed air and left to dry out outside in the sun on a very warm day. The solid wire colors can be cleaned with a flash wipe of acetone. The wires with strips color can be tuned up if necessary with denatured alcohol. being careful not to over due as it could remove strip color if wiping too long
Good luck!
Hi Mike - sorry if I missed it: do you/can you replace the retaining clips that hold the harness etc in place? I'm too hesitant to rip one off incase they can't be replaced.... The two pronged ones with the rubber outer sleeve. Thanks
Hello eljimberino
The retaining clips/clamps will remain in place. They are spot welded and would be difficult to replace and reinstall.
I did replace the vinyl sleeves with shrink tubing to clean them up and that seems to work well
Good Luck!
@@MikesRestorations Brilliant thanks!
Hello Mike, did you use a high temperatur paint for those flapper boxes? Or would a regular paint be sufficient? Thanks
Hello Lukasz
Yes you are correct..high temputure engine paint should work fine on the flapper boxes. They will get quite hot..engine paint is good to about 500-550 degrees
Good Luck!
Hi Mike, what paint did you use to paint the red heat control valves? Thanks in advance!
Hello AWCC
The paint used was dupli-color engine paint DE 1605 Ford red
Thanks Mike!