For the last couple of weeks I have been installing my own kitchen for the first time and getting to the end. I could not have done this without your brilliant videos. Thank you for pulling together such well detailed instructions 👍
Should of used the clips provided for the sink mate I’ve just fit the same one last week. I usually bed the sink down like you have and leave some weight on it until silicone goes goes off. Belts and braces 👍🏼
From the front edge 50 to 60 millimeters (5-6 cm). Cut the hole 9 to 10 mm (0.9-1 cm) smaller all around. Before you install the sink, install the tap, which makes it easier.
I brought a similar sink in black, it says in manual knock out hole with a punch and hammer, did you do that or did u use a 35mm core bit to make tap hole
Very nice, those colours are a good combo together. Could stainless sink be mounted the same way like you did here with silicone? The one I have here didn't come with any rubber gaskets but some strange strips of, erm, putty or something like that, dont know what those are for.
Thanks for your comment, yes you can do it this was with a stainless sink, just be sure to weigh it down whilst the silicon is going off. You want to make sure that it is flat all the way around. Hope this helps
Hi buddy, glad you’ve found the channel ! They’ll be loads more videos to come, if you want a video on anything please do let me know, no I don’t think so buddy, never heard of the channel, I’ll have to check it out, glad you’ve subbed and glad to have you on board 👍🏻
![[UNCUT] เก็บ "สจ.โต้ง" เอี่ยวมาเฟีย รู้ตัวคนบงการ ก่อนสั่งลั่นไก I คนดังนั่งเคลียร์ I 13 ธ.ค.67](http://i.ytimg.com/vi/o-J_p62D40w/mqdefault.jpg)
For the last couple of weeks I have been installing my own kitchen for the first time and getting to the end. I could not have done this without your brilliant videos. Thank you for pulling together such well detailed instructions 👍
That’s awesome ! Really glad I could help you ! And thanks for taking the time to tell me !
Nice one , you made that look very straightforward, many thanks.
Thank you very much 🍻
Should of used the clips provided for the sink mate I’ve just fit the same one last week. I usually bed the sink down like you have and leave some weight on it until silicone goes goes off. Belts and braces 👍🏼
Thanks for the videos. Really helpful. Would you follow the same steps for an epoxy sink going into an oak worktop? Seal & Silicone the edge?
Hi Christian, yes I would buddy 🍻
Good video Lewis. Great tip about the Sharpie 👏👏👏
Cheers vic 👍🏻
Excellent as ever.
Cheers Allen ! Much appreciated 🍻
From the front edge 50 to 60 millimeters (5-6 cm).
Cut the hole 9 to 10 mm (0.9-1 cm) smaller all around.
Before you install the sink, install the tap, which makes it easier.
What blade was you using in the jigsaw was it a down cutting or normal blade
I was using a Bosch up cut blade buddy, nice new one and take your time
Thanks for the advice. Great video.
Thanks for the comment buddy ! Glad I could help 🍻
Just one question the first mark before the white tape did you apply the tape inside the mark or outside the mark
I covered the mark up if that makes sense, you can faintly see the mark through the masking tape afterwards
Really great and helpful video
Cheers buddy really appreciate the comment! 🍻
This video is wicked, thanks for the help mate, just abt to make my sink project!
Cheers buddy ! And good luck with yours ! Glad I could help
Cheers
Thanks bud, well thought out and presented video.
Top man 👍
Cheers Peter for the comment! Appreciate it 🍻👍
How did you cut that small piece? Upside down we it’s a circular saw or with the router an jig ?
Hi buddy, I used a jig saw for this
do you secure the sink just with the silicone
Yes I do.
did you jigsaw straight through the carcasses?
Yes I did I use extra long bits
How do you cut out a tap hole when its not marked on the sink? Thanks
I use a 32mm diamond drill bit from the underside
@@LTWCarpentry Thank you
I brought a similar sink in black, it says in manual knock out hole with a punch and hammer, did you do that or did u use a 35mm core bit to make tap hole
I use a 35mm core bit but only because I have one. I have done it many a time with hammer and a punch mate
Very nice, those colours are a good combo together.
Could stainless sink be mounted the same way like you did here with silicone? The one I have here didn't come with any rubber gaskets but some strange strips of, erm, putty or something like that, dont know what those are for.
Thanks for your comment, yes you can do it this was with a stainless sink, just be sure to weigh it down whilst the silicon is going off. You want to make sure that it is flat all the way around. Hope this helps
@@LTWCarpentry thank you 👍
@@bluewanderer9903 your welcome
Top man!
Cheers Johnathan 🍻
Nice one mate. Don't you attach your taps first? Isn't it a pain to fix them in after the sink is fitted? 👍
Cheers mate, honestly yes I normally do but I forgot 😂😂😂
@@LTWCarpentry 😂😂👍
Nice job mate, do like a bit of squeeze out 🤣👊
Thanks a lot!
You're welcome!
Good video,I have that job to do and was wondering what type of blade you use in the jigsaw is it just standard or a reverse cut blade?
I used a normal blade in mine but it is advisable to use a downward cut as the laminate can chip. 👍🏻
Thank you.
Nice
Thanks buddy 🍻
No mechanical fixings?
Not on these sinks mate, they are so heavy they hold them selves, the stainless ones I use them
Normally use guide saw for cutting out and try do it before fitting worktop
Yes I do normally but not many people have a tracksaw so I wanted to use tools that most people have, thanks for the comment buddy 👍🏻
Great video !!! Thank You
Thank you Michael 👍🏻
Thank that's great ❤
Tops 🎉
Cheers Richard 👍🏻
Hi mate you explained it best and clear way possible rest I watched are dumb wits
Thanks mate you are a star
Nice one buddy ! I really appreciate it ! 🍻
Surely it’s easier to tool off the silicone while it’s wet
Not in my opinion no, you just tend to swear it
hi Lewis just found you on youtube brill videos buddy do you have anything in common with where's my pencil do you oh just subscribed
Hi buddy, glad you’ve found the channel ! They’ll be loads more videos to come, if you want a video on anything please do let me know, no I don’t think so buddy, never heard of the channel, I’ll have to check it out, glad you’ve subbed and glad to have you on board 👍🏻
Wicked video babe!!! Xxxx
Thank you babes xxxx
🔥🔥🔥🔥🔥🔥🔥