How the SU carburetter works - Part 1

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 พ.ย. 2024

ความคิดเห็น • 21

  • @rayshortall588
    @rayshortall588 6 ชั่วโมงที่ผ่านมา +1

    I do like your clearly explained videos. I've been in this game for a long time,but it does no harm to listen to the whys and wherefores . By the whey, I've throne away more than enough perfectly good wax jets in the past!

  • @philhuggett4776
    @philhuggett4776 9 ชั่วโมงที่ผ่านมา +1

    Im enjoying my home tutoring 😁 So interesting. Thanks AC

  • @davidgerrard8661
    @davidgerrard8661 7 ชั่วโมงที่ผ่านมา +1

    Excellent, thanks

  • @Goose_from_Norway
    @Goose_from_Norway 9 ชั่วโมงที่ผ่านมา +1

    Extremely interesting video, AC. The SU is an ingenious contraption and a beautiful piece of engineering. Thanks for a great video👍

  • @keithoftheshire2805
    @keithoftheshire2805 9 ชั่วโมงที่ผ่านมา +1

    Clear and concise quality information.....👍

  • @mcmotors100
    @mcmotors100 ชั่วโมงที่ผ่านมา +1

    Great video 👍I’d love you to explain how the Hif choke works? Thanks.

  • @Hipyon
    @Hipyon 9 ชั่วโมงที่ผ่านมา

    Nice one Constant depression carburettors are beautiful things And you mentioned the importance of the crankcase ventilation👍 it is positively dangerous to disconnect it Carbon monoxide isn't friendly

    • @ACDodd
      @ACDodd  9 ชั่วโมงที่ผ่านมา

      I would not say it was dangerous but it’s most definitely not healthy for you.

  • @pablojimenez8329
    @pablojimenez8329 5 ชั่วโมงที่ผ่านมา +1

    Great video! If I’m understanding well, the momentary enrichment of fuel when opening the throttle happens because the RPMs go up faster than the piston goes up (because of the delay effect caused by the damper), thus the air velocity momentarily increases because the open cross section in the carb body is still small (piston still down) causing a higher Venturi effect in the jet-needle?

    • @ACDodd
      @ACDodd  5 ชั่วโมงที่ผ่านมา

      Yes

  • @demiquadfpv3333
    @demiquadfpv3333 8 ชั่วโมงที่ผ่านมา +1

    Great video, one of the most confusing things learning when a piston flys up (thin oil etc) it leans, which I'll admit was not what I used to think due to thinking the needle was pulling out and therefore must be enriching. As a side request you once did a videos with a weight (lay shaft I think) to show approximately the drop speed on a carb, would you be able to show that test on this hs4 please?

    • @ACDodd
      @ACDodd  8 ชั่วโมงที่ผ่านมา

      Use the same test. It’s only starting point, and still maybe miles out for your actual car.

  • @martinhibbert1428
    @martinhibbert1428 8 ชั่วโมงที่ผ่านมา +1

    Does the float chamber need to be mounted with a rubber mount between it and the carb body ? I was always under the impression that if they were mounted solidly then vibration could cause problems with the fuel supply.

    • @ACDodd
      @ACDodd  8 ชั่วโมงที่ผ่านมา +1

      Only rubber mounted on the twin carb models, can’t say I have ever seen an issue on the single carb applications using a solid mount.

    • @martinhibbert1428
      @martinhibbert1428 8 ชั่วโมงที่ผ่านมา

      @ That’s interesting, never knew that. Both my cars are twin carbs and it’s 30+ years since I have owned a mini so don’t recall how the float chamber was mounted.

  • @kathysarmcandy1992
    @kathysarmcandy1992 5 ชั่วโมงที่ผ่านมา +1

    You do do some pretty units. Is that some satin clean on the body?

    • @ACDodd
      @ACDodd  5 ชั่วโมงที่ผ่านมา

      No.

    • @kathysarmcandy1992
      @kathysarmcandy1992 5 ชั่วโมงที่ผ่านมา +1

      @@ACDodd I was kidding. 🤟 Are you using a tumbling media for body cleaning?

    • @ACDodd
      @ACDodd  4 ชั่วโมงที่ผ่านมา

      @ no tumbling

  • @stuwhite2337
    @stuwhite2337 3 ชั่วโมงที่ผ่านมา +1

    Do you prefer hs or hif as a general rule?

    • @ACDodd
      @ACDodd  2 ชั่วโมงที่ผ่านมา

      HIF is a better carb full stop.