I have successfully configured outgoing calls from my FreePBX. Is there a way to route incoming calls to an extension or ring group? Incoming calls are dropped with the current configuration.
Hi sir, I am able to connect and call from pbx to mobile,, but I am unable to hear any sound in both side (on zoiper and other phone) Can you please help me?
Can you make a video for the inbound route part? I am not able to call my phone connected to FreePBX by bluetooth and redirect that call to an Extension.
I tried with android - nokia 8 more specifically. The pbx is actually behaving like a headset and just performing a regular call. How do I route that back to the extension I called from?
I've followed these instructions and am able to place calls but the audio always automatically routes to the cell phone. There is no audio on either direction from the IP phone behind Asterisk. If I try to switch manually on the iPhone 6 to Bluetooth, the call drops. Has anyone resolved this? I'm on a Raspberry Pi 3B.
Hi Sir, flawless. It worked perfectly. Thank You. However there is a slight issue on my side. Whenever I restart / reboot asterisk. Iphone seems to require another pairing, and this happend everytime. Is there a way for Iphone to actually auto connect bluetooth to asterisk / raspbx like other accessories ?
I'm getting an error. "Skipping adapter hci0. voice setting must be 0x0060" I changed it to 0x0060 (as it was set to 0xb000), then run chan_mobile again but it still shows the same error error. I rebooted the server and it reverts back to 0xb000. Do you have any suggestions?
Thanks! how we can use this method for more than 1 mobile ? i connected another usb Bluetooth adapter to raspberry , but when i use " hcitool dev" it shows devices list empty
Hi. There could be many reasons for that. It might require a restart of dbus, bluetooth, bluez or alike. In my case I connected USB adapter (in addition to built-in) and both were visible. And course check with 'lsusb' if you can see the device.
To my knowledge, since it works like a legacy Bluetooth pairing, it should not depend on the device. I tried iPhone and some unknown Android ... both worked the same way as in video.
@@rudradev1pal I this the list of chan_dongle compatible devices was not updated in some time. I never tried with 4G. However, driver creator named it "huawei 3g dongle channel driver" so it might not work witk 4G. And about this video and problem with Oneplus 6, I found this information regarding firmware problem: community.asterisk.org/t/chan-mobile-and-no-audio/75566
@@HOTKEY404 Hi At last I solved the issue after googling and using bluetoothctl the problem was resolved. BTW your video helped a lot. Thank you. Also, a request if you can create a video that shows forwarding an incoming call to an extension using chan_mobile. I will be really waiting for that. Really appreciate your help.
Thank you for your very useful video. I have outgoing calls working with my 'RealMe 7 Pro' phone using an Asus BT211 dongle running on a Pi2. (I tried a Pi3 but the inbuilt bluetooth didn't work, or, at least, it was highly distorted). However, my efforts in setting up FreePBX for an incoming call have so far failed. The incoming call lands on the mobile, then briefly and "accept/Reject' comes on the screen before the caller is transferred to the mobile provider's voicemail . Please could you explain this final piece in the jigsaw so I can get it all working :-)
Thanks! Great tutorial! I just have a problem that when I try the "mobile search" command, the phone asks me for a passcode to connect to the bluetooth and nothing that I enter works. Do you know how to bypass this?
Witam. Czy myślisz nad zrobieniem filmu jak połączyć telefon IP (np. Cisco IP phone 7941 albo inny) albo na przykład dwa takie telefony i żeby mogły one łączyć się wewnętrznie? Jestem nowy w tym temacie i ciekawi mnie to :D Liczę na odpowiedź :))
Ostatnie miesiące mieliśmy generalną modernizację strony i sklepu internetowego. Już wyszliśmy na prostą, więc wracamy do publikacji na YT. Mamy kilka tematów już gotowych do nagrania 😉 Konfiguracja połączeń to jeden z nich.
This video will help you to connect your phone to Asterisk. You will be able to eg. share mobile trunk among many extensions. Really ... depends on you needs 😉
Are you sure this works? In my experience (and what I read about the experiences of others), using RPi4's built-in Bluetooth will create garbled inbound audio but clear outbound audio. This was tested with Samsung Galaxy S3 and Google Pixel 2. To fix it, I had to get a compatible USB Bluetooth dongle listed here www.voip-info.org/chanmobile/. The consensus seems to be that an old Bluetooth module (like 2.0) is necessary for audio to work properly. Moreover, it should be noted that for some mobile phones SMS can be supported over Bluetooth. It is possible to pass SMS to Asterisk... if the mobile supports it.
@@HOTKEY404 note that i had to change to context=from-trunk instead of context=incoming-mobile for the incoming route to work. otherwise most excellent tutorial
Thank you very much!! Your videos are incredibly useful and well explained.
Everything works like a charm on a dedicated PC and FreePBX. Regards!!
Thank you! this is super helpful. Can you use a cable instead of bluetooth ? I just feel a cable might be more reliable.
I have successfully configured outgoing calls from my FreePBX. Is there a way to route incoming calls to an extension or ring group? Incoming calls are dropped with the current configuration.
Hi sir, I am able to connect and call from pbx to mobile,, but I am unable to hear any sound in both side (on zoiper and other phone) Can you please help me?
Is it possible using usb cable?
Can you make a video for the inbound route part? I am not able to call my phone connected to FreePBX by bluetooth and redirect that call to an Extension.
change to context=from-trunk instead of context=incoming-mobile in the conf file
10:52
I can't place any calls for my sip client, i think i am missing the part connecting the chan_mobile to the sip user, any useful guide ? Thanks
You need to add a Custom Trunk and use the trunk in Outbound Route.
I tried with android - nokia 8 more specifically. The pbx is actually behaving like a headset and just performing a regular call. How do I route that back to the extension I called from?
How do I set up inbound routing? I can't receive incoming calls from external callers.
change to context=from-trunk instead of context=incoming-mobile in the conf file
I've followed these instructions and am able to place calls but the audio always automatically routes to the cell phone. There is no audio on either direction from the IP phone behind Asterisk. If I try to switch manually on the iPhone 6 to Bluetooth, the call drops. Has anyone resolved this? I'm on a Raspberry Pi 3B.
Is there any way to connect the phone with raspberry using USB cable instead of Bluetooth?
Good question .... never heard of it 🤷♀️ When I stumble upon something like this I'll let you know. Usually people use chan_dongle or chan_mobile.
Hello! Thanks shared! Is it possible with wifi? If so, how? Unfortunately, the quality on bluetooth is quite bad.
Hi Sir, flawless. It worked perfectly. Thank You. However there is a slight issue on my side. Whenever I restart / reboot asterisk. Iphone
seems to require another pairing, and this happend everytime. Is there a way for Iphone to actually auto connect bluetooth
to asterisk / raspbx like other accessories ?
I'm getting an error. "Skipping adapter hci0. voice setting must be 0x0060" I changed it to 0x0060 (as it was set to 0xb000), then run chan_mobile again but it still shows the same error error. I rebooted the server and it reverts back to 0xb000. Do you have any suggestions?
how to use for sip server win?
Thanks! how we can use this method for more than 1 mobile ? i connected another usb Bluetooth adapter to raspberry , but when i use " hcitool dev" it shows devices list empty
Hi. There could be many reasons for that. It might require a restart of dbus, bluetooth, bluez or alike.
In my case I connected USB adapter (in addition to built-in) and both were visible. And course check with 'lsusb' if you can see the device.
Hello, is it possible to add more than one smartphone? and automaticaly switch between these 2 phones if one of them is not available?
That would require some testing. But if both are paired and connected to Asterisk, then it's quite simple to do a failover
Nice video, thanks for detailed tutorial.
774
i checked this solution on Raspberry Pi 4,, it works good but called number voice quality is very bad , do you have any idea about it ?
I've heard it might depend on RPI version, module version and your phone. Some have tried pairing with bluetoothctl command.
Do you have a list of recently available mobiles that support chan_mobile trunking. More specifically with android devices
To my knowledge, since it works like a legacy Bluetooth pairing, it should not depend on the device. I tried iPhone and some unknown Android ... both worked the same way as in video.
@@HOTKEY404 I tried to use oneplus 6 with android 10 but not able to hear anything
@@HOTKEY404 Also can you please tell me what are the recent chan_dongles available in the market. Does it work with a 4g LTE dongle?
@@rudradev1pal I this the list of chan_dongle compatible devices was not updated in some time. I never tried with 4G. However, driver creator named it "huawei 3g dongle channel driver" so it might not work witk 4G. And about this video and problem with Oneplus 6, I found this information regarding firmware problem: community.asterisk.org/t/chan-mobile-and-no-audio/75566
@@HOTKEY404 Hi At last I solved the issue after googling and using bluetoothctl the problem was resolved. BTW your video helped a lot. Thank you. Also, a request if you can create a video that shows forwarding an incoming call to an extension using chan_mobile. I will be really waiting for that. Really appreciate your help.
Thank you for your very useful video. I have outgoing calls working with my 'RealMe 7 Pro' phone using an Asus BT211 dongle running on a Pi2. (I tried a Pi3 but the inbuilt bluetooth didn't work, or, at least, it was highly distorted). However, my efforts in setting up FreePBX for an incoming call have so far failed. The incoming call lands on the mobile, then briefly and "accept/Reject' comes on the screen before the caller is transferred to the mobile provider's voicemail . Please could you explain this final piece in the jigsaw so I can get it all working :-)
change to context=from-trunk instead of context=incoming-mobile in the conf file
Thanks! Great tutorial! I just have a problem that when I try the "mobile search" command, the phone asks me for a passcode to connect to the bluetooth and nothing that I enter works. Do you know how to bypass this?
I was able to fix the problem by pairing using bluetoothctl and then continue with chan_mobile :D
Witam. Czy myślisz nad zrobieniem filmu jak połączyć telefon IP (np. Cisco IP phone 7941 albo inny) albo na przykład dwa takie telefony i żeby mogły one łączyć się wewnętrznie? Jestem nowy w tym temacie i ciekawi mnie to :D Liczę na odpowiedź :))
Ostatnie miesiące mieliśmy generalną modernizację strony i sklepu internetowego. Już wyszliśmy na prostą, więc wracamy do publikacji na YT. Mamy kilka tematów już gotowych do nagrania 😉 Konfiguracja połączeń to jeden z nich.
Is this video to convert phone to gsm gateway?
This video will help you to connect your phone to Asterisk. You will be able to eg. share mobile trunk among many extensions. Really ... depends on you needs 😉
Very interresting thanks
TFS
Are you sure this works? In my experience (and what I read about the experiences of others), using RPi4's built-in Bluetooth will create garbled inbound audio but clear outbound audio. This was tested with Samsung Galaxy S3 and Google Pixel 2. To fix it, I had to get a compatible USB Bluetooth dongle listed here www.voip-info.org/chanmobile/. The consensus seems to be that an old Bluetooth module (like 2.0) is necessary for audio to work properly.
Moreover, it should be noted that for some mobile phones SMS can be supported over Bluetooth. It is possible to pass SMS to Asterisk... if the mobile supports it.
I haven’t noticed audio problems. Will check…..
And there a separate video on messages in production.
But thanks for the tip 👍
Ture, I am having bad quality with inbound audio. Can anyone help?
@@HOTKEY404 note that i had to change to context=from-trunk instead of context=incoming-mobile for the incoming route to work. otherwise most excellent tutorial