ฝัง
- เผยแพร่เมื่อ 1 ม.ค. 2020
- I built a water bath for the MPCNC (Mostly Printed CNC) to cut carbon fiber parts. The first piece was a test piece to check if it even works. I cut a pocket to check the fiber direction underneath the top layer of the carbon fiber sheet. The main part I wanted to cut was the FPV Toothpick frame at the end from Dave_C FPV.
www.buymeacoffee.com/Quadropus
Incomplete Part List for MPCNC (Affiliate):
Belt GT2: amzn.to/2HhL38J
Stepper Motors: amzn.to/2OSi67i
Power Supply: amzn.to/37skYhI
CNC Shield and Motor Drivers: amzn.to/39pdmOu
Lead Screw: amzn.to/2UVjNoB
Ballbearings: amzn.to/2OUCtku - วิทยาศาสตร์และเทคโนโลยี
![ขายสมบัติ Ferrari 488 ลูกรักก!! l [Nickynachat]](http://i.ytimg.com/vi/pwF1Il1Uevw/mqdefault.jpg)
Hey. Erstmal danke für dein Video. Es beruhigt mich schon mal zu sehen das Carbon mit der mpcnc funktioniert. Habe bisher kein anderes Video gesehen.
Welche Fräsertypen (Firma) nutzt du für Carbon und Aluminium ?
Also rein um Bauteile wie Frames auszufräsen?
Hey, danke für das Feedback.
Ich nutze Fräser von Sorotec (Größe 1/8"). Diese sind recht günstig und scheinen gut zu fräsen. Ich nutze 1 und 2 Schneider mit Upcut in 2mm und 3mm für Alu und Kunststoffe und 2mm und 3mm diamantverzahnte für Carbon.
Nice work! It's funny. That's the exact frame I want to cut with my MPCNC and this will be my first attempt at cutting carbon fiber. I just need to build a bath with some way of holding the carbon sheet in place. Did you end up building the rest of the quad?
Hey, yes I did! You can check my Instagram and see the final build.
This is interesting because I am thinking about replacing some aluminum parts on the X axis of my Tevo Tarantula Pro. Is the water bath the best option over vacuum extraction?
Hey, I think the water bath is the safest solution regarding health. I don’t know how well the vacuum filtration works and I can imagine that not all particles are caught. Thus, primarily for the safety, I used the water bath.
are you using the stlcam version with ramps?
Hey, no I use the Estlcam Version for the Arduino Uno together with an GRBL shield.
So I am about to do the same thing. I need to cut out some CF frames for my T-Rex 600E RC helicopter. I'm just curious how much splatter of CF you saw even with using the water? Reason I ask is my machine is set up in the floor beside my desk and I'm worried about getting CF everywhere. I figured the water would cut down on it a lot, but I noticed you showed your controller which looked like it had bits of CF splatter on it. I noticed later that you added a makeshift dust shoe around the spindle. How much more did that help?
Hey, the splatter you saw on my controller was CF dust trapped inside water droplets. I can not make out any pure CF dust when using the water path. The "dust shoe" removed all the splatter I had while cutting with the water bath.
@@Quadropus Awesome! Thank you sir!
Use a vibrating saw/multi tool or a rotary disc to cut the tabs that are holding the parts.
I should have done that, but I only used the tabs on the test part.
The carbon fiber sheet was sticked on the foam with double sided tape and I did not use tabs on the quadcopter frame.
Hi, compliment for your work. How you have connected the Joypad Xbox wireless with the PC? I have some joypad, but i don't know how I can connect it with the PC. I buyed on ebay an adaptator, but win10 don't recognize it. Thanks and sorryfor my bad engliesh
Hey, thank you! This is an original XBox 360 wireless controller for Windows. It came with a connection dongle already.
How did you secure your carbon fiber to your base?
Hey, I used double sided tape on a piece of depron.
richtig gute Idee das Wasserbad, um alle Partikel zu sammeln. Wie hast du die Carbon platte in dem Wasserbad befestigt?
Hey, danke! Ich habe die Carbonplatte mit doppelseitigem Klebeband auf ein Stück Depron geklebt und das dann in das Wasserband geklebt. In dem Video für das GFK Fräsen sieht man es genauer 👍🏼
hey .. what speed are you using in your dremel and what speed :) i also have cnc and dremel for the router :) what bits did you use :) will subscribe to this :)
Hey, all settings are listet in the video! Roughly 25000rpm with a 2mm diamond cut end mill and 160-320mm/min feed rate. :)
hi, what bit size you used for the 2mm motors mounts? or you use only one bit? planning to cut some cf also. Have my mpcnc setup also but i might make the build vloume a little bit smaller for rigidity. Thanks
Hey, I used a 3mm bit for the contours and a 2mm bit for the holes. Good luck with the CF! 👍🏼
@@Quadropus Also what method you used to mount the carbon fiber?
I glued Depron inside the water bath with double sided tape and used painters tape on the Depron and the carbon fiber and glued them together with super glue.
@@Quadropus Nice. Thank you. Cant wait to try cutting
Hi :)
whats the work area of your MPCNC ?
Hey, the work area is about 23x23cm! :)
Hey! What did you make the white tray out of?
Hey, it is just a prepainted MDF panel and some plastic profiles for the walls.
The edges are sealed with silicone.
Quadropus thanks!
Mega cooles Video! Ich bin gerade am überlegen meine eigene MPCNC zu bauen, um auch Carbonplatten für meine Drohne zu fräsen. Wie teuer und zeitaufwändig war das Projekt bei dir?
Hey, danke für das Feedback! Ich habe ca. zwei Wochen benötigt und es hat unter 300€ gekostet. Den Dremel und hatte ich bereits. Ich kann nochmal schauen ob ich meine Auflistung der Kosten finde. 😬
Kugellager: 28,90€
Zahnriemen & Umlenkrollen: 11,99€
Schrittmotoren: 32,99€
Netzteil: 10,99€
CNC Shield & Treiber: 10,99€
Gewindespindel: 11,99€
Die Materialien aus dem Baumarkt (Rohre, MDF-Platte, Schrauben) habe ich nicht notiert.
Quadropus Teile selbst gedruckt? Die Kosten fehlen auch oder?
Ja, die Teile habe ich selbst gedruckt. Das Filament habe ich nicht aufgelistet, müssten aber ca. 2kg gewesen sein. Genau habe ich das aber nicht beachtet. Ich habe das Filament verwendet welches ich bereits hatte.
Quadropus ansonsten supercooles Teil. Stelle gerade meine Teile zusammen um mir auch eine zu bauen.
Moin wie hast du das Wasserbad gebaut? Baue meine mpcnc grade zusammen. Welchen Fremden nutzt du da?
Das Wasserbad ist eine 12mm starke MDF Platte mit Kunststoffbeschichtung. Für die Wände habe ich 40mm breite Kunststoffprofile benutzt, welche an die Seiten geschraubt wurden. Abgedichtet wurde es mit Silikon. Das Wasserbad wurde dann mit doppelseitigem Klebeband auf die MDF Platte der MPCNC geklebt.
Was meinst du mit "Fremden"?
Quadropus dremel sollte es heißen :-)
Das ist der Dremel 4000, werde aber im Zukunft auf einen AMB Fräsmotor umsteigen.
how did you make water bath, need to do this for my CNC machine
Hey, I basically used melamine coated wood, screwed plastic profiles to the side of it and sealed it with silicone.
The part was the glued on a piece of depron using double sided waterproof tape and then water was added.
What software are you using? How did you incorporate the Xbox controller? Thanks for video
Hey, I use EstlCam and it has XBox controller support built in.
@@Quadropus I have never seen the screen you have at 0:24 in Estlcam, I will have to find that, thank you!
As far as I remember the short cut to open the control panel is F2. 🤔
@@Quadropus wow I completely missed that part of the program. Lol one year late, thank you.
CF is scary to me.
The water bath makes it relatively safe in terms of regarding the dust. The cutting is easier than I expected.