Spring Service 4: Ford 8600 fuel filter change Bleed Injector pump Start up Ford 9600 filter timelap

We start here with finishing up the Fuel filter change on the 8600, and bleeding fuel through the injector pump. Give her a fire up, and move on to 9600 Fuel filter time lapse.
Thanks for watching hope you enjoy.

[@hauslogd]

I have been trying to get my tractor running again for 6 weeks after changing the fuel filter. You showed me my problem in the first 30 seconds of your video. I had the seal pushed down in the filter blocking the fuel from coming down. Thank you very much!

[@farm2655]

you would be surprised at how often that happens
thanks for commenting

[@sproket168]

Lol me too bud

[@sproket168]

Nealy just dragged it into the bonfire 😅.

[@regmair851]

nice.....good info.....thanks from Alberta.

[@farm2655]

thanks hopefully we will see you around again

[@ericlakota6512]

These fords are nice old girls if you do all your own work and need big cheep power they are what you need i realy like ford tractors

[@farm2655]

if its big cheap power you need id look at versatile or steiger both are cheaper power than ford

[@corysimonson9720]

Thanks great tips

[@farm2655]

Thanks, hope to see you around again.

[@55tmilam]

Great video! I have a 6600

[@farm2655]

Awesome! Thank you!

[@Framlife351]

TW-20 over here. Blue power!

[@wildernessoutdoors6875]

Have you done injectors on the 8600 yet? Getting ready to change mine but can’t find any videos on it.

[@Hyngyynj]

How can you tell when the filters are full

[@roelonzo]

so I saw that on the 9600 you have a Y splitter on the heater hose to connect the block heater , are you happy with the way it's working ?

[@farm2655]

I'm not real happy with it, its better to pull from the bottom of the radiator, and heat into the bottom of the block. But it does work.

[@qualitymovers4573]

I have a question about transmission fluid on the 8600. I just got a 8600 and was trying to find out if the transmission and hydraulic fluid are both added at the same place in the rear. I take it the dipstick on left side under rear filter is for trans?

[@farm2655]

yep you are correct dip stick that goes down around the axle is trans / hydraulic, both are added by the top 3 point arms, you do have to watch out for the earlier ones though the trans and rear end can be 2 separate oil compartments

[@qualitymovers4573]

@@farm2655 so just a universal trans/hydraulic fluid should work?

[@jaredblumenshine]

So I have a question. I'm looking at picking up an 8600 and the guy told me the hydraulic pump is out of it. Can you give me some insight on how to change it

[@farm2655]

So basically it is just below the levers, more to the bottom of the transmission, the control valves should come off and it is behind that plate. long story short, if you get one of those reprinted manuals it points it out a bit better than I can describe, but its not a huge splitting job or any thing like that.
Thanks for the comment.

[@wianjacobs5176]

Hi just whant to find out if my ford struggel to start but runs well after start is it the timing on the fuel pump

[@farm2655]

Was your timing moved recently? I wouldn't be looking there first, what's left on injector life are they holding preassure? is your service pump leaking? Alot of things can be the cause of poor starting, are your rings getting long in the tooth, Its hard to tell you your tractor isn't in front of me.

[@davidmacleod527]

hi can i putting a 12 volt pump on pressure would be lower pressure pump to push the fuel through lines ?can i leave pump on all the time .thank you

[@farm2655]

I'm sure you could as long as you meter pressure, not sure why you would want to though, the original service pumps are not all that expensive, and there is plenty of aftermarket availability as well

[@davidmacleod527]

@@farm2655 well i cant get my 674 international tractor to go ' so i can put hand pump on ;were would i put it would i cut the line and do it that why thank you for getting back to me david

[@charliematt4808]

Can you please tell me where to purchase ‘75 Ford 3000 tractor parts. I need spindles, injector pump and steering parts.

[@farm2655]

I’ve been getting more and more from the new Holland dealership

[@wianjacobs5176]

So dis 8600 doesn't have a turbo..?

[@farm2655]

Nope, and I don't think it ever will get one.

[@wianjacobs5176]

What is its pulling horsepower?

[@farm2655]

Nebraska tests claim 110 pto and 11363 pull

[@owenanderson3870]

What's the part number for thoes filters?

[@farm2655]

Off the top of my head 33166 rings a bell but would have to look it up to be certain.

[@owenanderson3870]

I found them at Napa thank you