Hope everyone enjoyed the video. Don't forget to click that like button and subscribe to show your support. K&N Filter Cleaning Kit www.knfilters.com/search/produ...
hello well i have a ford fiesta 2012 and i dont know it if it would make my mpg go up more or what it would do for me but i would get like a 3.76 hp gain is what i seen from K&N but i dont trust AEM
You should NOT put the oil on the inside or on the "engine" side of airbox of the filter. Specially if you car has a MAF sensor. The oil will damage the sensor.
@skullz189gaming I accept that challenge. Might be a month cause I have other things in the works. Subscribe and like the facebook page to stay updated.
+Daniel W Ya I don't see why not. Just shake up the oil can for a bit. I've used one that was prob 4 or 5 years old. Anything, spray a little on a rag and make sure it comes out red
Will do, thanks. I recently acquired a '14 Chevy Spark and debated on getting one but wondering if that particular vehicle would benefit from it since it isn't designed to go at warp speeds lol.
if you ever redo your heads, look and see how pitted they are from these "high flow" filters, your motor won't blow up but its life and efficiency will be reduced over time
i have this fucking problem, plz help me in this one ___----- after cleaning the filter i lubed with sqeezer it after 20 min allowed 20 min to wick it as per manual, my bike choked every time i accelerated ok i thought i put too much oil or left it wet, after that i degreased it again and left it to dry for a day even put it under sun to dry completely then lubed it with minimum oil and let it wick for a day then also after installing it choked .....can any one tell me what causing me this ?
This filter isn't K&N, this is a JLT intake system. Filter is similar to K&N. But K&N has always been a favorite filter brand of mine. No reason in particular.
Using the K&N cleaning kit is unnecessary and costly ,you can use soapy warm water to soak and rinse the filter ,after that air dry the filter once dry you can apply any kind of mineral oil to the filter using baby oil and spray bottle from a dollar store just spray with oil and re install bact to your car and your done ,total cost $2.00 and your time ...
i have this fucking problem, plz help me in this one ___----- after cleaning the filter i lubed with sqeezer it after 20 min allowed 20 min to wick it as per manual, my bike choked every time i accelerated ok i thought i put too much oil or left it wet, after that i degreased it again and left it to dry for a day even put it under sun to dry completely then lubed it with minimum oil and let it wick for a day then also after installing it choked .....can any one tell me what causing me this ?
Very informational, these step my step guides help a lot especially since you show every step.
@HDArtwork Thanks for always showing support.
Nice vid
Thanx man !
@budlightsk8er Made this 2 weeks when I did the other one. I prepare and yes I work out.
GREAT video thank you! Nice ink too.
Thank you.
Thank you
many thanks...
many thanks bro...good job. btw can u tell me how to clean a monster sport air filter?
Good video very helpful
this was great
Great video!! Thank you ... And your wife is very sweet not killing you..
kkkkkkkkkkkk cool and "vero"!!
@budlightsk8er What....ya I work out.
@UWISHPROD lol i ment when speed it up
hello well i have a ford fiesta 2012 and i dont know it if it would make my mpg go up more or what it would do for me but i would get like a 3.76 hp gain is what i seen from K&N but i dont trust AEM
it does, and it runs with dry filter . as soon as i oil it even with 5-6 drops of kn oil is starts to choke.
Does your bike run without the filter?
@Importkiller696 Ya probably not....
You should NOT put the oil on the inside or on the "engine" side of airbox of the filter.
Specially if you car has a MAF sensor. The oil will damage the sensor.
Is it the same for cleaning a motorcycle's K&N air filter?
do you need to wait for a whole to dry?!
How long should you let the filter dry?
If it is made of the same material then this should work for it
@Importkiller696 hahaha FRAM is the best lol
@skullz189gaming I accept that challenge. Might be a month cause I have other things in the works. Subscribe and like the facebook page to stay updated.
Maybe go without oil. Not sure why it does that
協調って、刺青格好いい!
日本の漢字はそんなにかっこよく見られるのかな?( =①ω①=)
Can you use degreaser to clean it?
+b864r No
Man your fast!
I still have my cleaning/oil kit from '09. Would it still be good? I keep it in a cabinet in the garage.
+Daniel W Ya I don't see why not. Just shake up the oil can for a bit. I've used one that was prob 4 or 5 years old. Anything, spray a little on a rag and make sure it comes out red
Will do, thanks. I recently acquired a '14 Chevy Spark and debated on getting one but wondering if that particular vehicle would benefit from it since it isn't designed to go at warp speeds lol.
+Daniel W Haha good point. But a good filter can also help with mpg, slightly but still helps. And who wants to buy filters every year.
Daniel W
how long I have to clean air filter every 3 months
Just Us
how long I have to clean air filter
At least a couple hours
Yap... My fingers hurts...
do "how to shadow chrome you're wheels"
Thats how im running these days
if you ever redo your heads, look and see how pitted they are from these "high flow" filters, your motor won't blow up but its life and efficiency will be reduced over time
i have this fucking problem, plz help me in this one ___----- after cleaning the filter i lubed with sqeezer it after 20 min allowed 20 min to wick it as per manual, my bike choked every time i accelerated ok i thought i put too much oil or left it wet, after that i degreased it again and left it to dry for a day even put it under sun to dry completely then lubed it with minimum oil and let it wick for a day then also after installing it choked .....can any one tell me what causing me this ?
OHIO!
why k and n? why not afe?
You can use these same steps in cleaning any reusable filter.
i meant why did you decide to go with k and n instead of afe
This filter isn't K&N, this is a JLT intake system. Filter is similar to K&N. But K&N has always been a favorite filter brand of mine. No reason in particular.
Using the K&N cleaning kit is unnecessary and costly ,you can use soapy warm water to soak and rinse the filter ,after that air dry the filter once dry you can apply any kind of mineral oil to the filter using baby oil and spray bottle from a dollar store just spray with oil and re install bact to your car and your done ,total cost $2.00 and your time ...
The cleaner is toxic, so wear gloves, safety glasses, and a face mask.
Thank you
i have this fucking problem, plz help me in this one ___----- after cleaning the filter i lubed with sqeezer it after 20 min allowed 20 min to wick it as per manual, my bike choked every time i accelerated ok i thought i put too much oil or left it wet, after that i degreased it again and left it to dry for a day even put it under sun to dry completely then lubed it with minimum oil and let it wick for a day then also after installing it choked .....can any one tell me what causing me this ?