Fiesta - Ford B5/IB5 Gearbox selector shaft seal - Fiesta 2003
ฝัง
- เผยแพร่เมื่อ 25 ก.ค. 2024
- Just seen this video which shows the seal - but read all below
• vazamento de óleo! Tro...
There is no need to disconnect the joint 7F110 in the rubber boot sleeve, just undo the bolt HS2 and slide the 7F116 Lever Gear shift off the shaft. The whole 7K336 lever and 7F116 can then be moved out of the way as one piece :)
picasaweb.google.com/10201822...
picasaweb.google.com/10201822...
Oil leaking from gearbox on my 2003 Ford Fiesta TDCI. Turns out that the oil, which had creeped all over the gearbox and surrounding pipes and metal - was coming from the Gear selector shaft seal.
See also this brilliant photo guide to the seal replacement foro.fordecosportclub.com.ar/v....
I cannot thank you enough for this video! I've been trying to find what goes into that square hole, having inherited the car with the gear linkage hanging off the transmission, I knew there was a part missing. I've been looking everywhere online with no joy, then I found this video. It's part number 7c445!! Thank you so much!
Thanks Mark for sharing this video, I just bought a 2007 Focus and soon discovered same leak. Knowing now I can fix it and without gearbox removal makes my day. Many thanks!
Thanks Mark, your tips and experience were really helpful. I was able to to this job on the Mrs' Focus as if I'd done it all before, rather than as a learning experience. Cheers buddy!
Thanks for posting this video.
I did the very same job today and this video helped tremendously.
Only thing I would add is that after removing the single bolt holding the ball end joint component with the square hole in it, you may have to strike the part to get it off the end of the selector shaft as it would be rusted on, as mine was. Use a soft metal drift, copper or aluminium alloy, to avoid damage to the shaft. You really don't want to raise the surface diameter of the shaft with any knicks or dings that might damage the new seal while slipping it on the shaft. Clean both shaft as end piece with fine emery cloth to remove any rust, grease lightly and reassemble after inserting the seal. Great tip on using the tape to protect the seal on assembly and using the ring spanner to help insertion.
Thanks again.
+goober650NX tape and spanner is Ford's tip - but glad the video helped
Yeeeeees! At last I made it! Thank you so much for the video!
That little screw was a pain! I had to cut a third of the head off to be able to use a wrench.
Thank you for this video. Very helpful.
thanks for posting and doing the edits
Thank you for tutorial, done my today
that circlip fell off ,,,so i enjoyed this vid
5:44 I must inform the oil does NOT flow out. It starts dripping with thick drops, but surprisingly, looses very little oil. You can even go without using an oil pan underneath.
It seems to be a common problem in those gearboxes after several years. This retainer has to withstand rotational and horizontal movements.
Fortunately, the replacement is cheap and quite common.
it works the same for fiesta 2006 petrol? It can not suck the oil with a tube?
All B5/IB5 gearboxes should be the same.
Do you mean to drain the box?
Whats the part number for the seal and dust cover ? Thanks alot
See EcoSportMexico's photo at s892.photobucket.com/user/EcoSportMexico/media/Transmision/RetenSelector/ControlesExternos22.jpg.html
The seal and dust cover comes as one joined item
How did you remove the dust cover mines seized on and will not budge!
The rubber dust cover on the shaft - or the plastic cover over the whole thing?
Rubber dustcover should slide off. Plastic cover has lugs that the clips need to be lifted over
How do you drain the oil from gear box to do an oil change?
Just seen this video which shows the drain and fill process
th-cam.com/video/wQhqCpjt7K4/w-d-xo.html
Hi there. I'm currently doing this on my 1.6 Focus. But I cant get the 7F116 lever off the selector shaft. I've removed the bolt but its still jammed on. I don't want to force it incase i damage something inside the gearbox though
+skyrat1991 If you've removed the torx head screw HS2 then it should slide off - but might be corroded on.
My photos at
picasaweb.google.com/102018229689562736636/Fiesta14TdciOilLeak#6199876311248097970
and look at
th-cam.com/users/redirect?q=http%3A%2F%2Fforo.fordecosportclub.com.ar%2Fviewtopic.php%3Ff%3D24%26t%3D598%26start%3D0%23p234985&redir_token=rN-Ou9wjuCPMim9ybDd8NjAhz1F8MTQ1MzM2NTQzNUAxNDUzMjc5MDM1
+Mark Ellis Nice one mate :-). Managed to get it off this morning. The shaft was corroded slightly so drowned it in WD40 last night. Needed a few gentle taps with a copper hammer but I finally managed to slide it off. New seals now on so I just need to refill the oil and put it back together
Thanks for the video mate! Noticed mine was leaking off my automatic 2003 fiesta would I have to fill back up or how to check how much is init?
Sorry, no idea. Not a mechanic. Try your nearest Auto Gearbox specialist, it's not expensive
Great Video
could you make a video removing the gearbox of de Ford fiesta Vehicle ?
+Rafael Zamora Sorry. I'm not a mechanic. Just a car owner who had a leak and who couldn't find any information on how to resolve the oil problem. I received so many bad or incorrect suggestions on what was causing this that I just had to make and share this
hola muy buen video pero me puedes ayudar dandome las medidas de las dos guayas de cambio del fiesta power
How to get those drawings that he showed in start of the video..??
Any Techs pls help...!!
Did you bother to read the full description text of the video?
The most important part of your work, you didn't film. Anyway is a great video.
Cierto, la parte más importante del video no la grabaste!
which was???
Still waiting for you to say what the most important part was, Mauricio
Great video but I’m having problems removing the gear shift bit how did you get it off?
Hello. Do you know why the shift lever 7k336 it's so heavy? I think it's not necessary. I think this part just próduce a horrible noise(CLANK).😵
1:14
Bom dia mano
Some one know the name of the part with the conector in the right hand of the imagen ,
alguien sabe como se llama la pieza que tiene el conector a un lado de lado derecho de la imagen ????
You've seen Drawing 2 at 15 seconds in?
Hlo
Why don't you use torch or some light while recording very poor light
Welcome to UK daylight, which has occasional clouds in the sky. You've noticed that I'm laid on a tarmac car park floor, and the car is not up on a garage car lift?
Si no sabes hacerlo no tiene sentido el video .no mostrado como se cambia retén
Did you read the English text?