Hello. What is the name of the connector that goes to the motor? why did you use the old cables? isn't that a source of error if you solder them together? greetings benjamin
Hey Benjamin, You're from Germany? No why it should be an error source? It's called bullet connector it's in different diameter available hope that helps 😉👍🏽 Nice regards ✌️🏽 😊
@@a-ztube source of error because of one more solder joint, I thought. but i have no idea about it either. Then I'll do it like you. Ok in German it means banana plug.😁
Hey man what do you mean? The stock esc is with build in receiver so only a new on from a new transmitter at about 6:00min you can see it and I put it an a blue balloon 😉👍🏽
So I have to upgrade the servo in mine because the 150a flycolor esc I put on is 5v system and the original esc was a 3v and the servo doesn't do much in the water with the new concept so gotta get a 20-25kg servo that is rated higher I think I will get one that is rated for as high as 7.4v just because I will be running up to 6s on the new motor (3670 surpass hobby 1900kv motor) and a 3 blade 437 37mm prop and eventually all metal fins, rudder. My end goal is to do 60+ mph ft011 and maybe after dialing it in top out around 75 mph we will see how it goes but I am doing away with the original battery tray and going to create a tunnel cover that goes over the shaft and also screws into where the plastic battery tray used to and maybe epoxy it to the other side not sure how I am going to do it figure it out when I get to that step but batteries will be able to mount on the board as well as maybe recounting the servo to the board not sure yet though anyway it's my project this fall and winter and will vid log my process of this project to completion hope all rc boat hobbyist will enjoy!
David Avery the Servo work even with the 150a esc 😉👍🏽 when my servo is damaged I would also use a better one that's always good. With the battery tray don't forget there's not that much space in the hight and with higher lipos they're bigger 😉 After all my upgrades I would also try a 37mm prop and to put the battery tray in the middle would also my next test because I want to build a flood chamber for better self righting 😉. With a perfect balance and good Motor Set up it should be possible I think even more than 75kmh Iam looking forward to your vid. Mate Nice regards
@@a-ztube ya man I assumed it was the voltage change but maybe it's just the servo is going bad cause it works fine out of water but under load it is like it cannot understand the radio sigals and doesn't hardly do anything maybe it's just a bad servo or some setting with the flysky gt3b that I am using with it
Hey my Friend 😊 You mean if you can leave everything stock like it is only put in an bigger Motor? If that's your question If you can fit into the motor mount or build something by yourself yes for sure 😉 👍🏽 But if you leave it on 4s with original esc it's not that much much more powerful you definitely have to change the propeller also 😉 Stay safe ✌️🏽 😊
You only need to change the esc and battery you can leave the stock Motor as you can see in my Video my Friend 😊 👍🏽 You're very welcome any time Stay safe ✌️🏽 😊
Hey bro, do you think that 5000mah 5s 100c battery will be too powerful for the in the box motor with 120A esc? Bit of a noob about this stuff and dont want to blow it up, Cheers bro
Hey bro also use higher 5s Lipo it should work,but 5000 should be to big I guess you need to checkt the Inside where the hull need to be closed from the height 😉
Hey mein bester, Du musst den esc tauschen damit du 5s fahren kannst den Empfänger / Fernbedienung must du nicht tauschen ich habe diese Fernbedienung für alle meine Fahrzeuge also bitte diese eine und setze in jedes Auto oder boot den Empfänger ein so kann ich mir 10 Fernbedienungen sparen Sie kann nämlich 10 Modelle abspeichern dazu ist sie sehr gut und günstig auch die Empfänger dafür sollte mal einer kaputt gehen kann ich mir empfehlen 👍🏽 Meinst du wie lange der 5s lipo hält? LG ✌️🏽
Hey my Friend, To be honest I don't know anymore 😁🙈 but I think it wasn't set (that's mostly on boat esc) in forward and backwards. But allways get an esc program card it's not expensive and makes it so much easyer to set your esc. Programm card for Esc amzn.to/35N4zoN Stay safe ✌️🏽 😎
Hallo. Ich frage nochmal. Warum hast du die Kabel zusammen gelötet. Sind die sonst zu kurz? Braucht man dann auch einen neuen Sender und Fernbedienung? Grüße.
Hey hattest du Schonmal gefragt? Sorry oft gehen Kommentare auch unter hatte dazu mal ein Video gemacht 🙈.... An dem esc sind ja keine stecker dran gewesen und ich hatte damals auch keine und habe deswegen diese samt kabel drann gelötet 😉 Wenn ich mich recht erinnere ist der Empfänger einzelnd deswegen kannst du die funken Kombi auch weiter benutzen.... Da ich,aber viele Modelle habe und die flysky fsgt3 uns gerade deren Empfänger sehr günstig sind benutze ich unter anderem diese mittlerweile die flysky fsgt5 deren receiver sind zwar teurer,aber haben auch mehr funktioninen. Hoffe da hilft dir soweit LG 🙌🏽😉
I have a question about the original ESC. Many times with my 1500mah 95C battery when the boat is moving as soon as I press too hard on the accelerator it decelerates and afterwards it goes very slowly. It is normal.
@@samuelludy6388 I bet it's the 90c lipo if a 120c and the stock C work without any problems 😉 Normaly this problem comes if you put in a bigger prop and your esc is to small / weak than it will allways cut of because the esc gets drained to much C
@@a-ztube Does the original engine handle the 5s battery well? Won't it cause any extra wear on any part of the boat? Is this kit better? enaliexpress.com/item/4000075910559.html?spm=a2g0o.productlist.0.0.1dbd61d9gorGyD&algo_pvid=36734c24-a2c8-4cb5-9e84-16b74ebb6db6e6b8-6b8e6b8b6b8b8b8b8e6e4b b549-43cb-9ac8-c4ab3b5728e8 & ws_ab_test = searchweb0_0, searchweb201602_10, searchweb201603_52
Paulo Paios sorry can't open your link don't know why 🤔 For sure it's more stress on the parts but it works very good till now and upgrade other parts is always recommend or better but still not necessary for driving on 4-5 a lipo. You don't have that much shake and vibration when you will put in an INRUNNER Motor But then you will loose the self righting feature. Nice regards
Hi, I don't know what you mean with engine break 🤔? You have to set the esc to forward + reverse. And the punch to full so you are able to self righting 😉 but even with the stock esc and 4s lipo that problem can show up last week's I went out with my Feilun FT011 she turned around 3 times on the head and came back 2 times very easily 1 time I had to play a little bit with forward and reverse throttle. Always very important for self righting feature everything had to stay on its places, if lipo is to heavy or on the wrong place or not fixed 100% or the esc you will have issues with the self righting feature. Nice regards
Hey mate Do you mean how to program the esc without the programming card? That's a hard way with the controller / transmitter but possible or what do you mean? I didn't show in the video how to configure my esc with my flycolor esc programming card you can see that in other videos from me ( mad flow f1) you can configure only forward and forward reverse everything also with your transmitter. Nice regards
@@a-ztube Hello. its Feilun FT011 set and the Flysky Gt3c Radio. They are beautiful. and vi q works perfectly. I even have the Feilun FT011 set and the Flysky Gt3c transmitter. So I get a FlyColor 70a ESC the same as the video and I do not have programming card! I could get an "A HELP" statement to set up to revert with my flysky Gt3c transmitter Since I do not have a cardon, ESC is only forward and forward! Thank you for listening.
Yes my Friend you always have to take the same brand / name from your esc 😉 Here's a link from eBay rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.de%2Fulk%2Fitm%2F312427906217
Yes my Friend 😊 👍🏽 but I will test out some things in the future with flood chamber than it would be possible to take an stronger INRUNNER. Nice regards
Hey my Friend 😊, Yes for sure I have the joysway super mono x same as the ft012 look my other videos you can take this same rudder upgrading the motor to 4s isn't that nice you know the boat is very small and jumps a lot. I tested a bigger prop with an high C rated 3s lipo that's very very nice an really enough for that boat the problem is the Stock 30a esc shuts down after a few seconds. So upgrading to an small 50a esc put on a bigger prop and take a good high C rated 3s lipo is an very nice Upgrade for this small sized boats 😉 I'll help how I can just let me know Stay safe ✌️🏽 😊
Hey my friend that one I took from another boat from me but you only have to look at the right shaft diameter if you choose one 😉 I got a new alloy / metal one I think from ali express or ebay but I can't find it anymore it should be 4mm shaft diameter,in the next upgrade video you will see it. Nice regards
Yes for sure you can keep it stock but I would recommend if you also have some cars or boats get a flysky fsgt3 or a fsgt3b it's such an good and cheap radio / transmitter and the the receivers are very cheap you can save 10 different models so I highly recommend it but you didn't need to do it for the 5s setup. Nice regards
Yo bro I got a question I glued mine down like in your vid but I fill the tray up with glue and glued around it afterwards mine sits alot lower in the water and am fighting it to go into plane with bigger motor as well got a 3670 1900kv and a aquacraft water cooling jacket on it my question is I think with all the glue and the heavy 150a flycolor esc I might have to go back to the drawing board and remove glued tray all together and just double side tape the esc down so to loose as much weight as I can
Hey bro because of the glue and also the 150a flycolor esc I can't emagine that it behave like this cause my buddy has the 150a in its ft011 and still the same like mine 🤔 Do you changed the motor already to the 3670 with cooling jacket? Nice regards bro 🤜🏼🤛🏾
Yes Bro 😉🤜🏽🤛🏻 You can see it in my new video radiolink transmitter Iam driving the feilun ft011 there need to edit a small update driving video it ones felt off in the head and came back because of forward reverse....with all the (metal) Upgrades the Boat drives awesome really 😍👍🏽
@@denilpt1999 I only use the standard brake setting so off from throttle and the prop won't turn anymore....with the flycolor program card you can set the drag brake..... So should work maybe in the next 1-2 weeks I can check it when going on the water right now I don't have time to do
@@RenelPancho 5s lipo is 21Volt buddy that's enough for this setup. Other motor and flex shaft with coupler instead of the stock dog bone system it'll handle 6s lipo for sure aswell 😉
Yes you can set it to the voltage you want somewhere between 3,4v - 2,9v you can see it in My video No problem you're welcome 😊👍🏽 Do you want to make you're Feilun FT011 faster or only change esc? The Feilun stock is very nice. Nice regards
Ohhh I really don't know I'd never tested any speed of my Rc 's I don't have any GPS., but it's very nice on 5s. Maybe If your stock esc breaks one time you can make this upgrade? Yes I've been windsurfing / surfing / body board / skim boardIng since I was a little boy and started back last 2 years again, because we live in Germany and nereast place is Netherlands after that France Portugal Spain so on 😉. Nice regards
Yes it's always when you go one step above from a lipo and you also can hear it it's more aggressive it also shakes a lot because of the outrunner Motor i will do an Upgrade from the turn fins and stuff also but it's to cold now maybe a few weeks the Sommer weather comes step by step 🐠🌴. Oh very very nice where are you located? Nice regards
Yo man how do you get it to go into reverse so you can still self right? If with the transmitter can you upload a step by step on how to program with transmitter I am sure many people would thank you
Hey David, because it's a bit tricky I always use a programme card it's only a few €$ whatever 😁 But I will take a look and make a video with transmitter programming but you have to wait in the next days I will upload a few new videos from the Feilun FT011 than I will check the transmitter programing 😉👍🏽 Nice regards
Hi.what a great video !! Any heat issues with the stock motor rumning 5 S ? Which will be the perfect upgrade motor to use for this set up that fits in the stock motor mount and makes it run even faster ? Also please tell.me which upgrade turn fins would you use ? I want to.upgrade mine like yours. Many thanks !
Eduardo Nessim hey my Friend thank you very much ☺️ 👍🏽 you're welcome. For upgrade Turnfins look to my other Feilun FT011 VIDS into the video Description 😉. Well right now I didn't have to change the motor because it's not broken and it's very fast right now 😎🤙🏽 No I didn't had any issues Motor takes it perfect... Another one that fits in the original Motor mount I can't imagine that there's one and that it will work good you have to change the mount and the hole shaft /system for higher torque and kv think the plastic will break. But it's not impossible for sure new shaft and glue the motor mount into the hull and you can probably fit any Motor you want to. In the future for sure I'll upgrade another Motor system and let you know 😁🙌🏽 Nice regards my Friend stay safe ✌️🏽 😊
@@a-ztube thank so.much..stay safe too. So with the new 90 amp esc and a 5 s batt 2000 mah how many run mins do you get running it fast ? Can you fit a 5 s 3000 amp also for more running time ?
You're very welcome my Friend 😊 👍🏽 well I didn't measured it but it's nearly the same like with the stock 4s 😉. Hmmm I think if you find the right size with 3000mah lipo and you put the battery tray to the middle maybe the point is it has to be thin otherwise you can't close the hull also if there's to much weight it's possible that she didn't self right anymore and the most important point for me better get smaller lipos and change them when empty in that time all the parts can cool down Iam driving with this all my Rc's over years and didn't had any burned esc Motor or whatever. The parts with that high turning energy get very stressed give them rest and you'll haven't to replace parts or repair.thats my own opinion my Friend 😊 👍🏽 Nice regards
Ah okay no problem 😉 The 5s lipo is 2000mah so nearly the same run time like the stock 4s lipo. Yes it's very nice after all the upgrades 😉🤙🏽 Nice regards ✌️🏽
When changing esc you need allways a new receiver transmitter combo like DumboRC X6 banggood.app.link/m5hkNGwc7fb?5Y130935228052016013 Or FlySky GT3C banggood.app.link/mvXRO2Ac7fb?5Y130935228052016013 These are good and cheap
Warum lötet man die Stecker nicht direkt? Und die Halterung des ESC hätte man auch anpassen können. So knallt man mind 200g Heisskleber da rein. Irgendwie sieht das mehr nach Bastelei als nach Modellbau aus.
Danke für den tolles feedback 😁👍🏽 Warum sollte ich direkt andere stecker anlöten vom lipo wenn ich zig Arten in zig verschiedenen fahrzeugen habe da arbeite ich gerne mit adaptern warum auch nicht? Vieles kann man immer irgendwie anders machen,aber warum sollte es deswegen kein Modellbau seien 🤔? Modellbau ist immer basteln es gibt viele Leute mit Zeit, Lust,Geld,Werkzeuge und andere wiederum nicht. Die meisten meiner Follower sind nicht von der Traxxas / Arrma und Co. Brigade und schätzen es auch wenn dinge einfach umgesetzt werden 👌🏽 Alles Gute
@@a-ztube Ich sparch nicht davon ANDERE Stecker zu löten. Sondern den DORT gezeigten direkt zu löten, statt diese komische Kabelverbindung zu setzen. Erst lesen, dann antworten.
Ha ha 😂 mein Freund erstens bist du nicht in der Lage jemandem zu erzählen was er machen soll da du kein bißchen Höflichkeit besitzt und zweitens mach doch bitte einen großen Bogen um diesen Kanal wenn es dich stört was hier so gemacht wird danke 😉👍🏽 LG
@@a-ztube Weil ich meine Meinung sage? Wenn es nicht passt, muss man die Kommentarfunktion deaktivieren. Ansonsten muss man damit rechnen, dass es Leute gibt, die eben anderer Meinung sind. Achtso - Anrede Du wird immer gross geschrieben. Soviel zum Thema Höflichkeit. Aber gut, der Bogen um den Kanal wird sehr gross sein.
Hey my friend don't worry you have to set the esc like you can see in your manual with your transmitter or you have to buy a programm card 😉👍🏽 Nice regards
Amélie Layn ah okay that could be I didn't try it out maybe there's an voltage guard in the esc I can't check it anymore but all my upgrade esc work with all types of lipos. But why do you want to put in a 3s lipo? Nice regards
@@a-ztube Thanks, you’re the best!! I just ordered the same ESC as you did for my FT011 so I need to know what connectors go with the motor so I can solder them.
@@eramirez34er inside 4mm outside 5mm 😉 No Bro you're allways welcome no Problem that's what's this Channel and Hobby is all about 😉🤜🏽🤛🏻 Wish you luck and a lot of fun mine is hopefully in the next 1-2 two months in the water again weather is to cos now in Germany 😜😁 Stay safe ✌️🏽 😎 🏄🏽
Hey my Friend it's like stock it's enough you should give the parts allways give some rest to cool down.... Think about 10mins depends how you drive maybe up to 15 min.
You really didn’t have to cut the stock ESC. Just solder connectors on new ESC, connect it to the motor and switch 2 of the cables if the motor spins the wrong way.
My friend i have a problem with my ft011 i was upgraded my esc to flycolor 90A , new 4S 30C 2200Mah battery and new servo 13kg and stock motor so when we try to run the speed is very slow and please help me my friend to how to fixed this problem.
Hey my Friend, Hmm that sounds strange 🤔 2 easy problems to fix... - maybe you have to change the motor wires. - maybe you have to set the Throttle range right like in the description from the Flycolor Esc user booklet. That would be the first I would try.... Did you only change the esc or was your stock one before damaged? Did you take the stock transmitter and receiver? Nice regards
@@a-ztube we follow your video to connect the wire first from red blue black then we connect the battery then we set the controller into full throttle then we try the direction of propeller is in reverse direction so again we interchange the wire to blue, red & black so thats it the direction now is forward and again we try to test run the same result very slow...
Hola. Muy buen video y buena maquina. Yo queria preguntarle sobre la bateria que ha mostrado de 5s. Que tal le esta saliendo. La recomendaria para comprarla?? Muchas gracias. Hi. Very good video and good machine. I wanted to ask about the battery that has shown 5s. How is it coming out? I would recommend it to buy it ?? Many thanks
Hi. Very good video and good machine. I wanted to ask about the battery that has shown 5s. How is it coming out? I would recommend it to buy it ?? Many thanks
jonny diez paz Aaaah okay my Friend that's a lot. Yes I highly recommend that 5S Lipo it's powerful, cheap and fits 100% perfect in the Feilun FT011. Nice regards
jonny diez paz thank you my Friend, I will do my best and you're welcome any time let us know if you're doing this or other mods to your Feilun FT011. Nice regards
What type of esc are you using is it the same motor that it came with or did you change the motor by the way you have a fast boat great video my boat is a ft12 model came with a smaller battery than the ft11 mine a 11 volt and the one you have came with a 14 volt if I'm not writing thanks for any information would be appreciated Mike Holden out of north Carolina said that
Hey my friend you're welcome 😊 👍🏽 It's stock Motor but I changed the es to flycolor 90a it's necessary the stock esc will burn after some 5s runs. Yes you drive the ft012 with 3s lipo and the ft011 is with 4s lipo. You can see in my other videos the red small one it's called super mono x from joysway it's the same like yours very nice small boat you can tune and upgrade it also I love that boat. Any questions are welcome Nice regards 😊👍🏽
Minhtrao Ho thank you my friend. Hmm I don't think so the outrunner Motor also shakes too much but if you upgrade to an INRUNNER Motor and the Flycolor 120A or better 150A Esc it will work for sure. Nice regards
Hey thanks for ur reply.. well that sounds interesting I’d love to give t a go.. . But ya know more than me so hope to get helps as I’ll record and send the video to u if i do and im not a TH-camr so it’s all urs lol..
Minhtrao Ho your welcome my Friend. That's my goal to share these things so that everybody can do the same things. Keep it up my Friend Iam very interested in that 6s mod and I help you with everything I can do 😉👍🏽 Nice regards
Minhtrao Ho hey my Friend no you can use the stock one I only upgrade mine because I have a lot of boats and Cars and only want one transmitter instead of 10 😁... Do you mean if INRUNNER Motor is always waterproof? INRUNNER Motors are better water-cooled than outrunner I can put one link in the next message wich maybe work good and isn't very expensive. Nice regards
I made the upgrade in 5s the problem is that I burnt everything because the magnets of the stock engine come off when it turned suddenly the engine c is blocked at once and burnt the esc ...
Hey my friend, Oh what 😳 so sorry to hear about that why such problems? As you can see in my old videos and in the upcoming VIDS me and some friends of mine hadn't one of these problems in all the time, even the esc is up to 6s with the right setup. Nice regards
@@a-ztube I do not know how the magnets get off the engine cage can be due to the electromagnetic force too important in any case it has block the net motor ....
Tyrone Rai hey my Friend Hmmm I really didn't measure the time but it's like stock 4s lipo think somewhere between 5 and 10 Minutes but I will tell you exactly next time she's on the water 😉👍🏽 Nice regards
I have a question. You know how the regular esc it comes with has a feature of when it’s about to die, i has enough energy for just to bring it back? Does that esc also have that feature?
Franko Garcia yes my Friend the Flycolor Esc has the same feature like the stock one with a program card you can change all the settings also the power / voltage cut off maybe from 3,3v to 3,1v whatever. Nice regards
wow, nice .. I love to play rc boat, I have rc boat like that model and did not run for a couple of years,... can I ask you Sir is the flip over did not affected? because you change the ESC
For sure you're very welcome my Friend 😊 👍🏽 No now it worked every time the first try after the changed esc it doesn't work, but now without any problem. To be honest flip over function is allways not 100% to any kind of these boats somtimes it doesn't work water to rough lipos isn't full anymore 🙈 Nice regards
@@a-ztube ok thanks Sir, for this kind of boat I have a test run over a seaweeds , to test how strong to escape, and i prove that this boat is really strong..... it's on stock parts. th-cam.com/video/FPcog-J3Onw/w-d-xo.html
SEKLISTANG DRONISTA like I said my Friend you're very welcome no problem 😉 👍🏽 Yes they're very strong but maybe in the future because of these see weed algue issue Iam trying to convert into an jet boat 😁😍👍🏽 Have a nice weekend stay safe ✌️🏽 😎
Hey mate, Yes for sure no reason to change the receiver 😉 when only 70a I think you can only go up to 4s maybe it lasts a few runs but I don't think it would last forever. Nice regards
@@a-ztube Thank you for your reply. My boat have a problem like this video. Can you teaching me, how to fix it. th-cam.com/video/tF8D2ZSM2Ak/w-d-xo.html Thanks you.
Hi mate, Normally yes but after the esc Upgrade most time not didn't figure it out the same with another esc and the Flycolor Esc in 150A version but I have to try some mods with the battery place so I hope she will self righting after that again 😁👍🏽 Nice regards
@@a-ztube It is because the FT011 stock esc can change very quickly from forward to reverse. The seaking esc's i have tried in my FT011 did not respond fast enough to create the inertia needed for the self right. Is that how you feel also? Cheers,
Hey mate, Yes I think that should be the problem I also tried out everything with programming the Flycolor Esc but nothing helped. So I have an turnigy / Hobbyking esc that works great in another boat and I will give it a try in the Feilun FT011. Tell us if you found something that works good 😊👍🏽 Nice regards
It looks like you are using the stock motor and propeller. No problems with the motor overheating? I have a couple of these boats running larger props on stock electronics but always having motors burn up. Got fed up and started running a Volantex Atomic Cat. No overheating problems and even ran over 60 mph on 6s. Posted on you tube. Nice video!
79ltd hey mate, THX yes its stock Motor and no problem with overheating so far, but I drive 35mm prop. Next upgrade is metal prop bigger turn fins and bigger trimm tabs because of the outrunner Motor the Boat is shacking left and right. I will try next another INRUNNER Motor and some other little modifications everything is just to see how far and were we can go with the Feilun FT011. I know the volantex and I think that type of boat are better for higher speed Iwilll look for your video man. I like the self righting or flood chamber style of boats so I will try to get the best performance in speed and handling of self rescue 😁👍🏽 Keep it up my friend Nice regards
You can just plug it in,but I can't remember anymore if the reverse was activated from factory 🤔 in any case allways get an program card that fits to your esc makes life so easy 😁👍🏽
Flycolor ın bu özelliği çok kötü soketleri bağlıyosun uzun sürüyor bide kutu içinde olsa çok daha iyi olur poşet iyi olmuyo he ama herşeye rağmen en iyi esclerden birisi gayet başarılı
@@a-ztube This feature of Flycolor is very bad, you connect the sockets, it takes a long time, it would be much better if the bidet was in the box, the bag is not good, but despite everything, it is one of the best escs, it is very successful
A - Z tube yes, there really is haha! I just installed it two days ago... just waiting till I have time to run her! Ohhh and I went ahead and threw a 150esc on it 🤷🏽♀️ never hurts lmao it keeps it nice and stable at the top 🤘🏽
😂 den Song kannte ich bis dahin nicht ist halt ein Hintergrund song aus der TH-cam library 😁👍🏽 Kommt drauf an was du vor hast und ob es dir Platz technisch was ausmacht. Ft012 geht ganz locker mit funke in einen Rucksack bei der ft011 wird das nichts zb. FT011 ist durch die Größe etwas stabil er und fährt etwas schneller auf 5s natürlich einiges mehr.
@@a-ztube vielen Dank für deine schnelle Antwort ich bin ein absoluter Anfänger und möchte ungern selber dran basteln . Bei Amazon sehe ich ft012 und bei manchen steht auch upgraded. Keine Ahnung was da dann besser ist..bei ft012 denke ich automatisch dass es besser und schneller als ft011 ist. Auch mit dem mitgelieferten Akku ist ft011 schneller als da ft012 ?
Gerne mein bester kein Problem 😉👍🏽 Nein ist leider nicht der Fall ich sage mal grob die ft012 ist 30cm groß und fährt auf 3s lipo ( Batterie) und die ft011 ist ca 65cm groß und fährt auf 4s lipo ( batterie) was schneller ist. Dazu kommt noch durch die Größe kannst du mir der FT011 auch bei etwas unruhigem Wasser fahren holland Nord Deutschland wie auch immer mit der kleinen ft012 bist du schon eher auf einen ruhigen see gebunden sonst fliegt und taucht das Teil mehr als es fährt. Falls du banggood noch nicht kennst würde ich dir empfehlen dir dort per app einen Account zu machen dann bekommst du zum eh günstigeren Preis als bei Amazon ( kommt auch aus China siehe Lieferzeiten) auch noch 10% bei der ersten Bestellung. Und falls du in der Zukunft etwas brauchst kannst du durch täglichen check in und Bewertungen schreiben ( könntest du ja dann man ein Video machen und den link von TH-cam einfügen wäre direkt wieder etwas Werbung für deinen Kanal 😉) ganz unkompliziert Punkte sammeln die Geld sind und bekommst Ersatzteile sehr günstig dann [120,91€ 26% OFF]Feilun FT011 65CM 2.4G bürstenloses RC-Boots-Hochgeschwindigkeitsrennboot mit Wasserkühlsystem rc fahrzeuge from Spielzeug Hobbys und Roboter on banggood.com banggood.app.link/sH1eAv05n4?p=5Y130935228052016013 Ansonsten wäre Vllt. Auch noch die joysway super mono x das kleine rote boot in meinen Videos etwas für dich ist genau wie die ft012,aber aus England / Deutschland also Schneller alles bei dir 😉 Bei Fragen immer melden by the way cooler Kanal habe den gleichen Haarschnitt und auch Schonmal drüber nachgedacht 😁👍🏽
@@a-ztube mega nice für deine ausführliche Antwort danke ich dir sehr..das hat mir total geholfen .. habe direkt meine eBay Bestellung von 156 Euro ft011 storniert 😁 Ich bin super gespannt das Teil geht ja voll ab.. Hab das syma Spielzeug q7 aber 20 kmh ultra lahm.. Ich gebe dir gerne Bescheid wenn es angekommen ist.. hoffe da läuft kein Wasser rein und hat auch diesen doppelten Deckel wie die syma. Und haha nice..wegen Haare. Zieh durch und mach ne ht 😁🤙
Rich Hair mehr als gerne mein bester dafür ist der Kanal da 😉🤙🏽 Auf jedenfall gib mir bescheid wenn das Teil da ist und die ein oder andere Modifikation wie zb der metal propeller bringt dir in ein par Sekunden nochmal mehr Dampf wirst nicht enttäuscht seien von dem Boot 😉👍🏽 Minimal Wasser hast du immer im Boot,aber kein Thema und ja die FT011 hat auch die zwei Deckel 👍🏽 Werde mir heute abend erstmal ein paar deiner Videos ansehen 😁👍🏽 Bis dahin alles Gute
News & More mag seien mit dem richtigen Motor kv Set up und Prop geht das definitiv 😉 wenn du den Standard Motor,aber hast nicht. Welches Set up fährst du? LG
Hey,
How do you connect esc with the battery?
I saw the battery you put on has a different hole from the stock! How can i connect it?
Thank you
Hey my friend just an connector plug from xt60 to Tplug 😉 all the parts down below in my video description .
Have a nice day
Wow.. Iv been running this boat for over a year, and I thought mine was pretty quick standard with a 4s. I'll be doing this mod asap.
It's really nice mate I highly recommend it but I will do some other upgrades video is coming Stay tuned 😁👍🏽
Nice regards
Hello. What is the name of the connector that goes to the motor? why did you use the old cables? isn't that a source of error if you solder them together? greetings benjamin
Hey Benjamin,
You're from Germany?
No why it should be an error source?
It's called bullet connector it's in different diameter available hope that helps 😉👍🏽
Nice regards ✌️🏽 😊
@@a-ztube
source of error because of one more solder joint, I thought. but i have no idea about it either. Then I'll do it like you. Ok in German it means banana plug.😁
😁🙌🏽😂 ja bullet oder Bananen stecker das stimmt 😁🤜🏽🤛🏻
Yo where is the video where you change the reciever?
Hey man what do you mean?
The stock esc is with build in receiver so only a new on from a new transmitter at about 6:00min you can see it and I put it an a blue balloon 😉👍🏽
So I have to upgrade the servo in mine because the 150a flycolor esc I put on is 5v system and the original esc was a 3v and the servo doesn't do much in the water with the new concept so gotta get a 20-25kg servo that is rated higher I think I will get one that is rated for as high as 7.4v just because I will be running up to 6s on the new motor (3670 surpass hobby 1900kv motor) and a 3 blade 437 37mm prop and eventually all metal fins, rudder. My end goal is to do 60+ mph ft011 and maybe after dialing it in top out around 75 mph we will see how it goes but I am doing away with the original battery tray and going to create a tunnel cover that goes over the shaft and also screws into where the plastic battery tray used to and maybe epoxy it to the other side not sure how I am going to do it figure it out when I get to that step but batteries will be able to mount on the board as well as maybe recounting the servo to the board not sure yet though anyway it's my project this fall and winter and will vid log my process of this project to completion hope all rc boat hobbyist will enjoy!
David Avery the Servo work even with the 150a esc 😉👍🏽 when my servo is damaged I would also use a better one that's always good. With the battery tray don't forget there's not that much space in the hight and with higher lipos they're bigger 😉
After all my upgrades I would also try a 37mm prop and to put the battery tray in the middle would also my next test because I want to build a flood chamber for better self righting 😉.
With a perfect balance and good Motor Set up it should be possible I think even more than 75kmh
Iam looking forward to your vid. Mate
Nice regards
@@a-ztube ya man I assumed it was the voltage change but maybe it's just the servo is going bad cause it works fine out of water but under load it is like it cannot understand the radio sigals and doesn't hardly do anything maybe it's just a bad servo or some setting with the flysky gt3b that I am using with it
@@a-ztube oh ya and if the prop works good I'll link the prop info from ebay where I got it for only $11 from china already balanced and sharpened
How fast is the boat running in this video?
Hey buddy didn't checked the speed,but it's really fast compared to the stock 4s 😉🤜🤛
Can i change the large moto, but keep the original receiver n esc, n upgrades 4s lipo. And what happening after change moto n battery
Hey my Friend 😊
You mean if you can leave everything stock like it is only put in an bigger Motor?
If that's your question If you can fit into the motor mount or build something by yourself yes for sure 😉 👍🏽
But if you leave it on 4s with original esc it's not that much much more powerful you definitely have to change the propeller also 😉
Stay safe ✌️🏽 😊
So i must replace the esc if want change bigger moto n battery? If not, my boat not powerful ya? Ok understand. Tq for sharing
You only need to change the esc and battery you can leave the stock Motor as you can see in my Video my Friend 😊 👍🏽
You're very welcome any time
Stay safe ✌️🏽 😊
Ok thank you also for sharing n guide, im newbie from malaysia
MashaALLAH 😍 👍🏽 You're allways welcome my Friend.
Have a nice weekend 😊 👍🏽
Do you think Flycolor ESC 90A can run well with Goolrc 2968 3400kv brushless motor and 4s Lipo?
Think that should
Thanks so much for the answer. Then no problem with 3s Lipo for sure?
In my opinion yes my Friend 😊 👍🏽
Hey bro, do you think that 5000mah 5s 100c battery will be too powerful for the in the box motor with 120A esc? Bit of a noob about this stuff and dont want to blow it up, Cheers bro
Hey bro also use higher 5s Lipo it should work,but 5000 should be to big I guess you need to checkt the Inside where the hull need to be closed from the height 😉
Thanks, very helpful!@@a-ztube
@@mitchellhirst3342 very welcome allways 😉🤜🤛
Hi muss ich die Fb Sender tauschen reicht nicht nur das Modul für 5s Akkus und hält der Akku?? Schonmal Danke
Hey mein bester,
Du musst den esc tauschen damit du 5s fahren kannst den Empfänger / Fernbedienung must du nicht tauschen ich habe diese Fernbedienung für alle meine Fahrzeuge also bitte diese eine und setze in jedes Auto oder boot den Empfänger ein so kann ich mir 10 Fernbedienungen sparen Sie kann nämlich 10 Modelle abspeichern dazu ist sie sehr gut und günstig auch die Empfänger dafür sollte mal einer kaputt gehen kann ich mir empfehlen 👍🏽
Meinst du wie lange der 5s lipo hält?
LG ✌️🏽
Hi! If the boat capsizes how did you solve the tipping with the new 90A esc?
Hey my Friend,
No problem it self rights mostly everytime the first 2 runs not but no I had never any problems hope that helps 😉 👍🏽
Nice regards
@@a-ztube thanks. Do you have to program the esc in a particular way or leave it set with a factory value?
Hey my Friend,
To be honest I don't know anymore 😁🙈 but I think it wasn't set (that's mostly on boat esc) in forward and backwards.
But allways get an esc program card it's not expensive and makes it so much easyer to set your esc.
Programm card for Esc
amzn.to/35N4zoN
Stay safe ✌️🏽 😎
Hallo. Ich frage nochmal.
Warum hast du die Kabel zusammen gelötet. Sind die sonst zu kurz? Braucht man dann auch einen neuen Sender und Fernbedienung?
Grüße.
Hey hattest du Schonmal gefragt? Sorry oft gehen Kommentare auch unter hatte dazu mal ein Video gemacht 🙈....
An dem esc sind ja keine stecker dran gewesen und ich hatte damals auch keine und habe deswegen diese samt kabel drann gelötet 😉
Wenn ich mich recht erinnere ist der Empfänger einzelnd deswegen kannst du die funken Kombi auch weiter benutzen....
Da ich,aber viele Modelle habe und die flysky fsgt3 uns gerade deren Empfänger sehr günstig sind benutze ich unter anderem diese mittlerweile die flysky fsgt5 deren receiver sind zwar teurer,aber haben auch mehr funktioninen.
Hoffe da hilft dir soweit
LG 🙌🏽😉
@@a-ztube Jo, danke. 👍
Immer gerne 😉🤜🏽🤛🏻
I have a question about the original ESC. Many times with my 1500mah 95C battery when the boat is moving as soon as I press too hard on the accelerator it decelerates and afterwards it goes very slowly. It is normal.
4s lipo?
@@a-ztube yeah
@@samuelludy6388 Ok I think the problem is the high C rate from your lipo....
Same problem with the stock one?
@@a-ztube No the stock one is ok but I have also a 120C and it goes verry well. Maybe it’s the ESC isn’t it ?
@@samuelludy6388 I bet it's the 90c lipo if a 120c and the stock C work without any problems 😉
Normaly this problem comes if you put in a bigger prop and your esc is to small / weak than it will allways cut of because the esc gets drained to much C
That music put me to sleep but I woke up when the boat hit the water NICE 👍👍
Thank you mate 😁 you're welcome new videos are coming soon ✌️🏽 nice regards
Almost sounds like it could turn a bigger prop.
Miguel Salami think so too if summer is coming back I will try and make a lot of videos mate 😉👍🏽
Do you also need to change the receiver and the controller? Or just just the battery and the drive?
It's not necessary to change the receiver and the transmitter my friend 😉👍🏽
Nice regards
@@a-ztube 👍
@@a-ztube Does the original engine handle the 5s battery well? Won't it cause any extra wear on any part of the boat?
Is this kit better?
enaliexpress.com/item/4000075910559.html?spm=a2g0o.productlist.0.0.1dbd61d9gorGyD&algo_pvid=36734c24-a2c8-4cb5-9e84-16b74ebb6db6e6b8-6b8e6b8b6b8b8b8b8e6e4b b549-43cb-9ac8-c4ab3b5728e8 & ws_ab_test = searchweb0_0, searchweb201602_10, searchweb201603_52
Paulo Paios sorry can't open your link don't know why 🤔
For sure it's more stress on the parts but it works very good till now and upgrade other parts is always recommend or better but still not necessary for driving on 4-5 a lipo.
You don't have that much shake and vibration when you will put in an INRUNNER Motor But then you will loose the self righting feature.
Nice regards
@@a-ztube pt.aliexpress.com/item/4000075910559.html?spm=a2g0o.productlist.0.0.584061d910D4Lm&algo_pvid=e1dafa81-0fda-44d4-b79c-c175e1f8fb99&algo_expid=e1dafa81-0fda-44d4-b79c-c175e1f8fb99-12&btsid=ab4dc314-e10a-45b9-b33c-3ca0768d44ef&ws_ab_test=searchweb0_0,searchweb201602_7,searchweb201603_52
Boat can turn around with new esc ? as we do not have the engine brake
Hi,
I don't know what you mean with engine break 🤔?
You have to set the esc to forward + reverse. And the punch to full so you are able to self righting 😉 but even with the stock esc and 4s lipo that problem can show up last week's I went out with my Feilun FT011 she turned around 3 times on the head and came back 2 times very easily 1 time I had to play a little bit with forward and reverse throttle.
Always very important for self righting feature everything had to stay on its places, if lipo is to heavy or on the wrong place or not fixed 100% or the esc you will have issues with the self righting feature.
Nice regards
@@a-ztube yes okey my esc has forwrd and reverse but i I have not tested yet return the boat with new esc. Its easy in return with new esc ??? Thanks
Amélie Layn do you mean that it turns around? I would say it's a bit harder then stock.
But maybe you can test it in your bathtub.
Nice regards
how to configure or enable this function neither Esc.
forward e reverse ( Bidirectional )
When pushing the throttle inti reverse.
Hey mate
Do you mean how to program the esc without the programming card? That's a hard way with the controller / transmitter but possible or what do you mean?
I didn't show in the video how to configure my esc with my flycolor esc programming card you can see that in other videos from me ( mad flow f1) you can configure only forward and forward reverse everything also with your transmitter.
Nice regards
@@a-ztube
Hello.
its Feilun FT011 set and the Flysky Gt3c Radio.
They are beautiful.
and vi q works perfectly.
I even have the Feilun FT011 set and the Flysky Gt3c transmitter.
So I get a FlyColor 70a ESC the same as the video and I do not have programming card!
I could get an "A HELP" statement to set up to revert with my flysky Gt3c transmitter
Since I do not have a cardon, ESC is only forward and forward!
Thank you for listening.
ThiagO AmantE hey my friend yes the programming card is not included you have to buy it from eBay or Hobbyking
Nice regards 😊
@@a-ztube Pode cartão de programação ser outro ???
ou tem que ser uma marca especial?
Yes my Friend you always have to take the same brand / name from your esc 😉
Here's a link from eBay rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.de%2Fulk%2Fitm%2F312427906217
is it the outrunner motor make the boat flip?
Yes my Friend 😊 👍🏽 but I will test out some things in the future with flood chamber than it would be possible to take an stronger INRUNNER.
Nice regards
Pq vc trocou o Up Grad
😁🙈 what?
Hey so I connected everything but I don’t know how to calibrate the ESC to go in reverse. Any advice?
Forget it I finally got it all to work. I can’t wait to put it in the water lol
Yes Bro 😍 👍🏽
Let me know.....
And allways the best to do this with an esc program card so much easier than everything else
Why not upgrade to xt60.. deans is limited on battery choice...🤔
Hey my Friend 😊 👍🏽 I have many lipos with deans and I ALLWAYS use xt60 adapter plugs if needed 😉
Nice regards
@@a-ztube ok i understand. No worries. Can i upgrade ft012 the same as this? Thank you
Hey my Friend 😊,
Yes for sure I have the joysway super mono x same as the ft012 look my other videos you can take this same rudder upgrading the motor to 4s isn't that nice you know the boat is very small and jumps a lot. I tested a bigger prop with an high C rated 3s lipo that's very very nice an really enough for that boat the problem is the Stock 30a esc shuts down after a few seconds. So upgrading to an small 50a esc put on a bigger prop and take a good high C rated 3s lipo is an very nice Upgrade for this small sized boats 😉
I'll help how I can just let me know
Stay safe ✌️🏽 😊
you have to program the esc to work properly ?
No its just fine tuning it works out of the box 👍🏽
Nice regards
You have no reverse?
Your a blessing! Glory to God in the highest! Jesus Chroist! Super cool mod and video! Thank you so much for sharing!
You're welcome my Friend 😊 👍🏽
can you tell me where you got the 35mm prop ? do all standard props fit ? i noticed thers a notch on the stock prop
Hey my friend that one I took from another boat from me but you only have to look at the right shaft diameter if you choose one 😉 I got a new alloy / metal one I think from ali express or ebay but I can't find it anymore it should be 4mm shaft diameter,in the next upgrade video you will see it.
Nice regards
anyone know what the stock motor and esc was in this boat???
Should be 65a ESC and 2400kv motor
did you have to program the esc ??
Hey mate,
No its with stock settings but you can I always prefer an program card👍🏽
Nice regards
did you change your receiver and remote .If you did do you have to or can you keep it stock
Yes for sure you can keep it stock but I would recommend if you also have some cars or boats get a flysky fsgt3 or a fsgt3b it's such an good and cheap radio / transmitter and the the receivers are very cheap you can save 10 different models so I highly recommend it but you didn't need to do it for the 5s setup.
Nice regards
Did you change the motor or just change the esc, looks so fast and wanna upgrade, not sure if the motor can take 5s😅
No bro stock motor and changed the esc 😉👍
@@a-ztube thanks bro appreciate it
Yo bro I got a question I glued mine down like in your vid but I fill the tray up with glue and glued around it afterwards mine sits alot lower in the water and am fighting it to go into plane with bigger motor as well got a 3670 1900kv and a aquacraft water cooling jacket on it my question is I think with all the glue and the heavy 150a flycolor esc I might have to go back to the drawing board and remove glued tray all together and just double side tape the esc down so to loose as much weight as I can
Do you think this is best?
Hey bro because of the glue and also the 150a flycolor esc I can't emagine that it behave like this cause my buddy has the 150a in its ft011 and still the same like mine 🤔
Do you changed the motor already to the 3670 with cooling jacket?
Nice regards bro 🤜🏼🤛🏾
Bro. Does this esc has. Forward reverse brake mode
Yes Bro 😉🤜🏽🤛🏻
You can see it in my new video radiolink transmitter Iam driving the feilun ft011 there need to edit a small update driving video it ones felt off in the head and came back because of forward reverse....with all the (metal) Upgrades the Boat drives awesome really 😍👍🏽
@@a-ztube so it is having drag brake. When shifting from. Forward to reverse
@@denilpt1999 I only use the standard brake setting so off from throttle and the prop won't turn anymore....with the flycolor program card you can set the drag brake.....
So should work maybe in the next 1-2 weeks I can check it when going on the water right now I don't have time to do
@@a-ztube thanks broo
You're very welcome 😉 🙌🏽
Very informative hope that you have a vedio upgrade on how to change motor also
Thx my friend 😊👍
No need to till now everything works fine 😂💪
Can you put more power battery like 22volts on that?
@@RenelPancho 5s lipo is 21Volt buddy that's enough for this setup. Other motor and flex shaft with coupler instead of the stock dog bone system it'll handle 6s lipo for sure aswell 😉
Tnks brother 😊
Is there a low battery indication on the boat? or on the boat when he slowed down as on the stock?
Thanks to reply
Yes you can set it to the voltage you want somewhere between 3,4v - 2,9v you can see it in My video
No problem you're welcome 😊👍🏽
Do you want to make you're Feilun FT011 faster or only change esc? The Feilun stock is very nice.
Nice regards
@@a-ztube
to have a feilun ft011 faster one reaches how much in kmh with the upgrade?
Do you practice windsurfing too?
thanks
Ohhh I really don't know I'd never tested any speed of my Rc 's I don't have any GPS., but it's very nice on 5s.
Maybe If your stock esc breaks one time you can make this upgrade?
Yes I've been windsurfing / surfing / body board / skim boardIng since I was a little boy and started back last 2 years again, because we live in Germany and nereast place is Netherlands after that France Portugal Spain so on 😉.
Nice regards
@@a-ztube agree but the difference in throttle power and top speed is better and is felt ??
I practice windsurf slalom and foil 😉
Yes it's always when you go one step above from a lipo and you also can hear it it's more aggressive it also shakes a lot because of the outrunner Motor i will do an Upgrade from the turn fins and stuff also but it's to cold now maybe a few weeks the Sommer weather comes step by step 🐠🌴.
Oh very very nice where are you located?
Nice regards
Yo man how do you get it to go into reverse so you can still self right? If with the transmitter can you upload a step by step on how to program with transmitter I am sure many people would thank you
Hey David, because it's a bit tricky I always use a programme card it's only a few €$ whatever 😁
But I will take a look and make a video with transmitter programming but you have to wait in the next days I will upload a few new videos from the Feilun FT011 than I will check the transmitter programing 😉👍🏽
Nice regards
Thanks bro
David Avery you're welcome 😊 👍🏽
Now You Need a Bigger pond Mate👍👍💛
Ha ha ha 😂 that's true my Friend 👍🏽
Hi.what a great video !! Any heat issues with the stock motor rumning 5 S ? Which will be the perfect upgrade motor to use for this set up that fits in the stock motor mount and makes it run even faster ? Also please tell.me which upgrade turn fins would you use ? I want to.upgrade mine
like yours. Many thanks !
Eduardo Nessim hey my Friend thank you very much ☺️ 👍🏽 you're welcome.
For upgrade Turnfins look to my other Feilun FT011 VIDS into the video Description 😉.
Well right now I didn't have to change the motor because it's not broken and it's very fast right now 😎🤙🏽
No I didn't had any issues Motor takes it perfect...
Another one that fits in the original Motor mount I can't imagine that there's one and that it will work good you have to change the mount and the hole shaft /system for higher torque and kv think the plastic will break.
But it's not impossible for sure new shaft and glue the motor mount into the hull and you can probably fit any Motor you want to.
In the future for sure I'll upgrade another Motor system and let you know 😁🙌🏽
Nice regards my Friend stay safe ✌️🏽 😊
@@a-ztube thank so.much..stay safe too. So with the new 90 amp esc and a 5 s batt 2000 mah how many run mins do you get running it fast
? Can you fit a 5 s 3000 amp also for more running time ?
You're very welcome my Friend 😊 👍🏽 well I didn't measured it but it's nearly the same like with the stock 4s 😉.
Hmmm I think if you find the right size with 3000mah lipo and you put the battery tray to the middle maybe the point is it has to be thin otherwise you can't close the hull also if there's to much weight it's possible that she didn't self right anymore and the most important point for me better get smaller lipos and change them when empty in that time all the parts can cool down Iam driving with this all my Rc's over years and didn't had any burned esc Motor or whatever.
The parts with that high turning energy get very stressed give them rest and you'll haven't to replace parts or repair.thats my own opinion my Friend 😊 👍🏽
Nice regards
@@a-ztube ok. How many mims of running time with that batt ? And no heat motor issues
Eduardo Nessim no heat Motor issues my friend min. Of run time maybe 10-15 minutes maybe more maybe less 😉
Autonomy ? 5 min ?
VirTuaL ToXiiNe Hey my Friend what du you mean 😁?
@@a-ztube i am french
it and the duration of the battery 5s ? Time ?
and after all your options do you find it better ?
Ah okay no problem 😉
The 5s lipo is 2000mah so nearly the same run time like the stock 4s lipo.
Yes it's very nice after all the upgrades 😉🤙🏽
Nice regards ✌️🏽
I have the same boat so this was good to know. Thanks for showing bud!!👍👍
Hey mate you're welcome 😊 👍🏽 and there's an update video coming up next.Nice regards
Do we have to have a new remote control ??
And is the Chanel receiver in the boat stock ?
And if it’s not where do we have to plug it ?
When changing esc you need allways a new receiver transmitter combo like
DumboRC X6 banggood.app.link/m5hkNGwc7fb?5Y130935228052016013
Or
FlySky GT3C
banggood.app.link/mvXRO2Ac7fb?5Y130935228052016013
These are good and cheap
Warum lötet man die Stecker nicht direkt? Und die Halterung des ESC hätte man auch anpassen können. So knallt man mind 200g Heisskleber da rein. Irgendwie sieht das mehr nach Bastelei als nach Modellbau aus.
Danke für den tolles feedback 😁👍🏽
Warum sollte ich direkt andere stecker anlöten vom lipo wenn ich zig Arten in zig verschiedenen fahrzeugen habe da arbeite ich gerne mit adaptern warum auch nicht?
Vieles kann man immer irgendwie anders machen,aber warum sollte es deswegen kein Modellbau seien 🤔?
Modellbau ist immer basteln es gibt viele Leute mit Zeit, Lust,Geld,Werkzeuge und andere wiederum nicht.
Die meisten meiner Follower sind nicht von der Traxxas / Arrma und Co. Brigade und schätzen es auch wenn dinge einfach umgesetzt werden 👌🏽
Alles Gute
@@a-ztube Ich sparch nicht davon ANDERE Stecker zu löten. Sondern den DORT gezeigten direkt zu löten, statt diese komische Kabelverbindung zu setzen. Erst lesen, dann antworten.
Ha ha 😂 mein Freund erstens bist du nicht in der Lage jemandem zu erzählen was er machen soll da du kein bißchen Höflichkeit besitzt und zweitens mach doch bitte einen großen Bogen um diesen Kanal wenn es dich stört was hier so gemacht wird danke 😉👍🏽
LG
@@a-ztube Weil ich meine Meinung sage? Wenn es nicht passt, muss man die Kommentarfunktion deaktivieren. Ansonsten muss man damit rechnen, dass es Leute gibt, die eben anderer Meinung sind.
Achtso - Anrede Du wird immer gross geschrieben. Soviel zum Thema Höflichkeit.
Aber gut, der Bogen um den Kanal wird sehr gross sein.
Danke schön 😍👍🏽
Did you do anything to the stock rudder. Mine only turns very, very wide compared to my BlackJack 24. Nice job. I will be copying you on this one!!!
Hey my Friend you're very welcome 😉 🙌🏽
Thank you very much ☺️ 🙏🏽
No I didn't do anything to the stock rudder I upgraded to metal one 😉🤜🏽🤛🏻
@@a-ztube I just ordered the upgraded metal one and it comes with the outside stabs for $18 bones. Not bad. Thanks for the quick reply!
You're very welcome 😉 🤜🏽🤛🏻
That's an good price bro really were did you ordered?
@@a-ztube Ali Express or something like that. I google searched and it popped up as one of the options.
Ah okay yes was wondering about that should work very good 👌🏽😍
Hello the reverse gear doesnt work for me whit the esc 90 help me please my friend!!
Hey my friend don't worry you have to set the esc like you can see in your manual with your transmitter or you have to buy a programm card 😉👍🏽
Nice regards
Whit the original comand It works change somethings??
What do you mean my friend?
The manual IS chinese i dont understand esc
Where i can buy programa card?
we can put 4s on upgrade boat ?
Hey my friend,
Yes for sure you can drive it with 3s if you want but it's slower.
Nice regards
okey because the basic esc stock does not accept my 3s battery ... Why ???
Amélie Layn ah okay that could be I didn't try it out maybe there's an voltage guard in the esc I can't check it anymore but all my upgrade esc work with all types of lipos.
But why do you want to put in a 3s lipo?
Nice regards
@@a-ztube
it's the only batteries I have ...
and use the batteries that I have already found to navigate longer
But the Feilun FT011 comes with a stock 4s lipo 🤔
Nice regards
J'ai fait tout les branchements pareil et le moteur bip et ne fonctionne pas 😰
Hey my Friend forgive me only englisch or German 🙈
Ciao complimenti, volevo chiederti la batteria è una 5s da quanti amò
Amp
Sorry don't understand you 🙈😁
Nice regards
Does anyone know what size connectors I need to buy so I can connect the ESC to the motor?
Hey my Friend wow nice to read you Again after so many years 😍😁🦾
You mean the 3 wire connecters?
@@a-ztube Yes the 3 wire connectors. Is it 4.0mm Banana Bullet Connectors?
@@eramirez34er I'll try to check later
@@a-ztube Thanks, you’re the best!! I just ordered the same ESC as you did for my FT011 so I need to know what connectors go with the motor so I can solder them.
@@eramirez34er inside 4mm outside 5mm 😉
No Bro you're allways welcome no Problem that's what's this Channel and Hobby is all about 😉🤜🏽🤛🏻
Wish you luck and a lot of fun mine is hopefully in the next 1-2 two months in the water again weather is to cos now in Germany 😜😁
Stay safe ✌️🏽 😎 🏄🏽
Hola muy buenos dónde se pueden comprar éso en que sitio
Hey my Friend please English or German 😉
No lo puedo leer solo leeo en español
English please my Friend
How much run time u get out of the battery
Hey my Friend it's like stock it's enough you should give the parts allways give some rest to cool down....
Think about 10mins depends how you drive maybe up to 15 min.
You really didn’t have to cut the stock ESC. Just solder connectors on new ESC, connect it to the motor and switch 2 of the cables if the motor spins the wrong way.
Yes for sure my friend that's true 👍🏽
,but if you don't have any connectors you have to take the stock ones 😉.
Nice regards
Probably want to make sure you have the right gauge wire for the extra juice and check your amps you will probably be pushing the motor pretty hard.
Hey my Friend works really perfect till now I think the only big issue could be the drive shaft.
Nice regards
@@a-ztube the drive shaft is definitely a weak point, ive blown 2 in stock form
Really? Wow even now on 5s no problem,but you're right upgrading to an flex shaft would be much better
Stock engine ??
m ch r yes My Friend stock engine 😉👍🏽
Nice regards
My friend i have a problem with my ft011 i was upgraded my esc to flycolor 90A , new 4S 30C 2200Mah battery and new servo 13kg and stock motor so when we try to run the speed is very slow and please help me my friend to how to fixed this problem.
Hey my Friend,
Hmm that sounds strange 🤔
2 easy problems to fix...
- maybe you have to change the motor wires.
- maybe you have to set the Throttle range right like in the description from the Flycolor Esc user booklet.
That would be the first I would try....
Did you only change the esc or was your stock one before damaged?
Did you take the stock transmitter and receiver?
Nice regards
Thanks my friend i will check it
And my friend i think the speed test of this boat after we test it out i think the speed is in
@@a-ztube we follow your video to connect the wire first from red blue black then we connect the battery then we set the controller into full throttle then we try the direction of propeller is in reverse direction so again we interchange the wire to blue, red & black so thats it the direction now is forward and again we try to test run the same result very slow...
Hmm stock transmitter and receiver?
Hola. Muy buen video y buena maquina. Yo queria preguntarle sobre la bateria que ha mostrado de 5s. Que tal le esta saliendo. La recomendaria para comprarla?? Muchas gracias.
Hi. Very good video and good machine. I wanted to ask about the battery that has shown 5s. How is it coming out? I would recommend it to buy it ?? Many thanks
jonny diez paz Hola Amigo,
Forgive me my Friend but I only can understand English or German :(
Nice regards
Hi. Very good video and good machine. I wanted to ask about the battery that has shown 5s. How is it coming out? I would recommend it to buy it ?? Many thanks
jonny diez paz Aaaah okay my Friend that's a lot.
Yes I highly recommend that 5S Lipo it's powerful, cheap and fits 100% perfect in the Feilun FT011.
Nice regards
@@a-ztube thank you very much friend. greetings and continue with videos like that. Greetings and thanks again
jonny diez paz thank you my Friend,
I will do my best and you're welcome any time let us know if you're doing this or other mods to your Feilun FT011.
Nice regards
Awesome...i,ll be trying this mod. But maybe with an upgraded motor to cope.
Hey my Friend thank you 😉🤙🏽
Yes that's also an good option if the stock Motor will break I would do the same 😉
Nice regards
Hi kyle...which motor will you recomend as the fastest upgrade that will fit in the stock motor mount? Thks
What type of esc are you using is it the same motor that it came with or did you change the motor by the way you have a fast boat great video my boat is a ft12 model came with a smaller battery than the ft11 mine a 11 volt and the one you have came with a 14 volt if I'm not writing thanks for any information would be appreciated Mike Holden out of north Carolina said that
Hey my friend you're welcome 😊 👍🏽
It's stock Motor but I changed the es to flycolor 90a it's necessary the stock esc will burn after some 5s runs.
Yes you drive the ft012 with 3s lipo and the ft011 is with 4s lipo.
You can see in my other videos the red small one it's called super mono x from joysway it's the same like yours very nice small boat you can tune and upgrade it also I love that boat.
Any questions are welcome
Nice regards 😊👍🏽
That’s a really nice job but i wonder if I change the motor too would it works on 6s?
Minhtrao Ho thank you my friend.
Hmm I don't think so the outrunner Motor also shakes too much but if you upgrade to an INRUNNER Motor and the Flycolor 120A or better 150A Esc it will work for sure.
Nice regards
Hey thanks for ur reply.. well that sounds interesting I’d love to give t a go.. . But ya know more than me so hope to get helps as I’ll record and send the video to u if i do and im not a TH-camr so it’s all urs lol..
Minhtrao Ho your welcome my Friend.
That's my goal to share these things so that everybody can do the same things.
Keep it up my Friend Iam very interested in that 6s mod and I help you with everything I can do 😉👍🏽
Nice regards
Perfect thanks very much. Is there any inrunner motor waterproof j advice ? And do i have to change the transmitter?
Minhtrao Ho hey my Friend no you can use the stock one I only upgrade mine because I have a lot of boats and Cars and only want one transmitter instead of 10 😁...
Do you mean if INRUNNER Motor is always waterproof?
INRUNNER Motors are better water-cooled than outrunner I can put one link in the next message wich maybe work good and isn't very expensive.
Nice regards
I made the upgrade in 5s the problem is that I burnt everything because the magnets of the stock engine come off when it turned suddenly the engine c is blocked at once and burnt the esc ...
Hey my friend,
Oh what 😳 so sorry to hear about that why such problems? As you can see in my old videos and in the upcoming VIDS me and some friends of mine hadn't one of these problems in all the time, even the esc is up to 6s with the right setup.
Nice regards
@@a-ztube
I do not know how the magnets get off the engine cage can be due to the electromagnetic force too important in any case it has block the net motor ....
Amélie Layn maybe your motor was bad produced or something like that 🤔
@@a-ztube yes maybe... The magnets just fix in the epoxy résine... In the motor cage it s weigtless
The motor is case att runing in 4s in the moment of broke
How much running time u get
Tyrone Rai hey my Friend Hmmm I really didn't measure the time but it's like stock 4s lipo think somewhere between 5 and 10 Minutes but I will tell you exactly next time she's on the water 😉👍🏽
Nice regards
I have a question. You know how the regular esc it comes with has a feature of when it’s about to die, i has enough energy for just to bring it back? Does that esc also have that feature?
Franko Garcia yes my Friend the Flycolor Esc has the same feature like the stock one with a program card you can change all the settings also the power / voltage cut off maybe from 3,3v to 3,1v whatever.
Nice regards
A - Z tube alright thanks for the help bud
No problem you're welcome.
Nice regards
@@a-ztube does it come with program card this esc?
Hi Mate,
No you have always to buy your program cards also for the matching Esc 😉👍🏽
Nice regards
wow, nice .. I love to play rc boat, I have rc boat like that model and did not run for a couple of years,... can I ask you Sir is the flip over did not affected? because you change the ESC
For sure you're very welcome my Friend 😊 👍🏽
No now it worked every time the first try after the changed esc it doesn't work, but now without any problem.
To be honest flip over function is allways not 100% to any kind of these boats somtimes it doesn't work water to rough lipos isn't full anymore 🙈
Nice regards
@@a-ztube ok thanks Sir, for this kind of boat I have a test run over a seaweeds , to test how strong to escape, and i prove that this boat is really strong..... it's on stock parts.
th-cam.com/video/FPcog-J3Onw/w-d-xo.html
SEKLISTANG DRONISTA like I said my Friend you're very welcome no problem 😉 👍🏽
Yes they're very strong but maybe in the future because of these see weed algue issue Iam trying to convert into an jet boat 😁😍👍🏽
Have a nice weekend stay safe ✌️🏽 😎
@@a-ztube hahaha, you have great idea Sir......
We'll see my Friend 😁🦾
Hi mate,
Can I keep the original receiver when I change the new ESC 90A?
And what happening with the boat when I change with ESC 70A?
Thank you.
Hey mate,
Yes for sure no reason to change the receiver 😉 when only 70a I think you can only go up to 4s maybe it lasts a few runs but I don't think it would last forever.
Nice regards
@@a-ztube Thank you for your reply.
My boat have a problem like this video. Can you teaching me, how to fix it.
th-cam.com/video/tF8D2ZSM2Ak/w-d-xo.html
Thanks you.
Awesome video!! Does it self right?
Hi mate, Normally yes but after the esc Upgrade most time not didn't figure it out the same with another esc and the Flycolor Esc in 150A version but I have to try some mods with the battery place so I hope she will self righting after that again 😁👍🏽
Nice regards
@@a-ztube It is because the FT011 stock esc can change very quickly from forward to reverse. The seaking esc's i have tried in my FT011 did not respond fast enough to create the inertia needed for the self right. Is that how you feel also?
Cheers,
Hey mate,
Yes I think that should be the problem I also tried out everything with programming the Flycolor Esc but nothing helped.
So I have an turnigy / Hobbyking esc that works great in another boat and I will give it a try in the Feilun FT011.
Tell us if you found something that works good 😊👍🏽
Nice regards
@@a-ztube I have actually been looking at those Turnigy Marine esc's, please let me know asap, if they are any different?! :D
I will my friend 😉 but it will take some time.
Nice regards
How long does the 5s battery last?
Azmi J I didn't stopped the time but it's enough really think the mostly the same time as the original 4s lipo. 😊👍🏽
Nice regards
It looks like you are using the stock motor and propeller. No problems with the motor overheating? I have a couple of these boats running larger props on stock electronics but always having motors burn up. Got fed up and started running a Volantex Atomic Cat. No overheating problems and even ran over 60 mph on 6s. Posted on you tube. Nice video!
79ltd hey mate,
THX yes its stock Motor and no problem with overheating so far, but I drive 35mm prop. Next upgrade is metal prop bigger turn fins and bigger trimm tabs because of the outrunner Motor the Boat is shacking left and right. I will try next another INRUNNER Motor and some other little modifications everything is just to see how far and were we can go with the Feilun FT011.
I know the volantex and I think that type of boat are better for higher speed Iwilll look for your video man. I like the self righting or flood chamber style of boats so I will try to get the best performance in speed and handling of self rescue 😁👍🏽
Keep it up my friend
Nice regards
Do I have to program the esc myself or can I just plug it in
You can just plug it in,but I can't remember anymore if the reverse was activated from factory 🤔 in any case allways get an program card that fits to your esc makes life so easy 😁👍🏽
Flycolor ın bu özelliği çok kötü soketleri bağlıyosun uzun sürüyor bide kutu içinde olsa çok daha iyi olur poşet iyi olmuyo he ama herşeye rağmen en iyi esclerden birisi gayet başarılı
Salam
Please German or English 😉👍🏽
@@a-ztube This feature of Flycolor is very bad, you connect the sockets, it takes a long time, it would be much better if the bidet was in the box, the bag is not good, but despite everything, it is one of the best escs, it is very successful
Ok kardeś
Thanks for your words and advice 😉👍🏽
You mean the receiver into the balloon?
Stay safe ✌️🏽 😎
@@a-ztube yes flycolor esc
He's safe with you 🙋🏻♂️
😉🙏🏽
Throw a 3930kv on this bad boy and tell me what you think! 😈 looking good so far my man! 🤙🏽
Nicholas Adams for sure bro there're a lot of ( better) ways to take this thing to fly 😎🤙🏽
Did you do it?
Thank you and nice regards ✌️🏽
A - Z tube yes, there really is haha! I just installed it two days ago... just waiting till I have time to run her! Ohhh and I went ahead and threw a 150esc on it 🤷🏽♀️ never hurts lmao it keeps it nice and stable at the top 🤘🏽
Nicholas Adams very nice bro 😉 👍🏽
So let me know what's up after you was on a ride ✌️🏽😎
A - Z tube will do brotha! 😁🤘🏽
@@nicholasadams9954 So.. how is it?
Bonjour merci pour la video
75km/h
Question? 😁
Yes
Ok 😁👍🏽 I didn't measured,but it's very fast nur next time I'll do a speed test 😉
@@a-ztube Tell me please, where can I find a tuning servo for this boat? Do you have a link?
I'll check it up tonight if I forget you please ask me again tomorrow 😉🤜🏽🤛🏻
Nice video
Thanks my Friend you're Welcome 😉 👍🏾
That's good!👍
Much appreciated ☺️🙏🏽
Have a nice day ✌️🏽 😊
Haha die Musik von mein Bizeps brennt 😂 besser fto11 oder ft012
😂 den Song kannte ich bis dahin nicht ist halt ein Hintergrund song aus der TH-cam library 😁👍🏽
Kommt drauf an was du vor hast und ob es dir Platz technisch was ausmacht.
Ft012 geht ganz locker mit funke in einen Rucksack bei der ft011 wird das nichts zb.
FT011 ist durch die Größe etwas stabil er und fährt etwas schneller auf 5s natürlich einiges mehr.
@@a-ztube vielen Dank für deine schnelle Antwort ich bin ein absoluter Anfänger und möchte ungern selber dran basteln . Bei Amazon sehe ich ft012 und bei manchen steht auch upgraded. Keine Ahnung was da dann besser ist..bei ft012 denke ich automatisch dass es besser und schneller als ft011 ist. Auch mit dem mitgelieferten Akku ist ft011 schneller als da ft012 ?
Gerne mein bester kein Problem 😉👍🏽
Nein ist leider nicht der Fall ich sage mal grob die ft012 ist 30cm groß und fährt auf 3s lipo ( Batterie) und die ft011 ist ca 65cm groß und fährt auf 4s lipo ( batterie) was schneller ist.
Dazu kommt noch durch die Größe kannst du mir der FT011 auch bei etwas unruhigem Wasser fahren holland Nord Deutschland wie auch immer mit der kleinen ft012 bist du schon eher auf einen ruhigen see gebunden sonst fliegt und taucht das Teil mehr als es fährt.
Falls du banggood noch nicht kennst würde ich dir empfehlen dir dort per app einen Account zu machen dann bekommst du zum eh günstigeren Preis als bei Amazon ( kommt auch aus China siehe Lieferzeiten) auch noch 10% bei der ersten Bestellung.
Und falls du in der Zukunft etwas brauchst kannst du durch täglichen check in und Bewertungen schreiben ( könntest du ja dann man ein Video machen und den link von TH-cam einfügen wäre direkt wieder etwas Werbung für deinen Kanal 😉) ganz unkompliziert Punkte sammeln die Geld sind und bekommst Ersatzteile sehr günstig dann
[120,91€ 26% OFF]Feilun FT011 65CM 2.4G bürstenloses RC-Boots-Hochgeschwindigkeitsrennboot mit Wasserkühlsystem rc fahrzeuge from Spielzeug Hobbys und Roboter on banggood.com banggood.app.link/sH1eAv05n4?p=5Y130935228052016013
Ansonsten wäre Vllt. Auch noch die joysway super mono x das kleine rote boot in meinen Videos etwas für dich ist genau wie die ft012,aber aus England / Deutschland also Schneller alles bei dir 😉
Bei Fragen immer melden by the way cooler Kanal habe den gleichen Haarschnitt und auch Schonmal drüber nachgedacht 😁👍🏽
@@a-ztube mega nice für deine ausführliche Antwort danke ich dir sehr..das hat mir total geholfen .. habe direkt meine eBay Bestellung von 156 Euro ft011 storniert 😁
Ich bin super gespannt das Teil geht ja voll ab.. Hab das syma Spielzeug q7 aber 20 kmh ultra lahm.. Ich gebe dir gerne Bescheid wenn es angekommen ist.. hoffe da läuft kein Wasser rein und hat auch diesen doppelten Deckel wie die syma.
Und haha nice..wegen Haare. Zieh durch und mach ne ht 😁🤙
Rich Hair mehr als gerne mein bester dafür ist der Kanal da 😉🤙🏽
Auf jedenfall gib mir bescheid wenn das Teil da ist und die ein oder andere Modifikation wie zb der metal propeller bringt dir in ein par Sekunden nochmal mehr Dampf wirst nicht enttäuscht seien von dem Boot 😉👍🏽
Minimal Wasser hast du immer im Boot,aber kein Thema und ja die FT011 hat auch die zwei Deckel 👍🏽
Werde mir heute abend erstmal ein paar deiner Videos ansehen 😁👍🏽
Bis dahin alles Gute
einfach geil
Vielen Dank mein bester 😉 👍🏾
LG
Süper Türkiye selamlar.
Salam u aleikum from germany bro 👍🏽
Da ist mein 4S aber schneller.
News & More mag seien mit dem richtigen Motor kv Set up und Prop geht das definitiv 😉 wenn du den Standard Motor,aber hast nicht.
Welches Set up fährst du?
LG
@@a-ztube ganz normal zurzeit. Feilun ft011/ 38mm CNC Prob. Alu Finnen und 4S 3500/60C mit Gps 86km/h
Next time desolder the connectors from the old. Noob 😂
Warum sollte ich das tun Kabel sollten länger seien Profi 😉
J'ai fait tout les branchements pareil et le moteur bip et ne fonctionne pas 😰
do you have the fly color esc programming card ?
I have same problem and same esc and remote
Hmm very strange.... Do you have the esc programme card?
@@a-ztube yaps but already fix that with a new remote 😅