I would have a lot of issues with the methods seen in this video and would not like if an amateur was to look at this as a proper guideline for operating a panel saw. Safety doesnt seem to be addressed in any way; the machine does not have a safety guard over the blade, and you can clearly be seen at 3.47 leaning in over the blade to retrieve the off-cut. Sheet material does not have an edge finish of adequate quality for most applications, so cutting datum edges would usually be the standard practice. I also would question the health and safety and the impact on quality of cut at 1.47 when you left the saw running in the incomplete cut, and again at 2.08 when the saw blade is distinctively louder due to the friction of it rubbing against the wood; a simple push through on the right hand side would solve this, and an outfeed table/roller would ensure the piece remains supported. Sorry to write an essay and criticise, I just think that there are far safer and better ways to use such a lovely machine!
+Patrick Kelly You are right if we take it the way how you´ve explained it. But the main idea was to show how I use special "helpers" to work on my own. but anyway thanks for your correct attitude to our profession. Rgds. Alex.
Вот так и я всё один таскал . До таскался((((( Уже девять месяцев не работаю Врачи категорически сказали не более пяти килограмм можно поднимать. Да что поднимать ходить долго не могу
wow another video on how NOT to use a sliding table saw . The number one safety instruction on these saws it stated right in the manual where it says " never use the crosscut fence in conjunction with the rip fence unless the rip fence is positioned to end just prior to the fron of the blade . using the two fences together can cause dangerous kickback
I've cut many huge Sheets on my own but dont work without a guard !!even worse when you video it absolutely no excuse or reason not to have a guard ,if you slip you fall on an exposed Blade ..why would you ??
One month later, i bought a proper guard for that machine. 2 years ago i bought proper Martin with a proper protection system.That was video only about helping equipment.
Это точно распиловщик? Как можно у вас поработать? За сколько? Я не хочу сказать, что всё хуёво, наоборот, мне очень понравилась скорость. Даже хромой справится в одиночку. Моя мечта, работать в своё удовольствие, минимум физических нагрузок, за исключением подачи. 😁😁😁 Одна беда, при наших объёмах, за такую скорость, руководитель застрелит тебя из шуруповёрта или пневмо-ППШ. Заморочек с подачей листа не понимаю, он замечательно подаётся по полу волоком, всё равно торцевать. Пирамида рядом... Приспособление интересное, но хрен его кто рабочему человек купит😁. Проще самому сделать. (Я себе моталку для стреча из октанрма и джокера сделал, чтоб не корячиться вниз головой мотая низ паллета) Не холодно ли зимой? Станок у ворот, сомнительное удовольствие.👍
I never attempt to cut a whole panel om my panel saw, since it's just very difficult to manage, unless I absolutely have too. I break them down in smaller units with a track saw first.
Thanks for comment. But, as you can see, it is also possible to cut entire sheet without any big efforts. Frankly saying, it is not show off, just my standard procedure when I am alone in my shop.
Человек оркестр) Хотя , в таком большом цеху обязаны быть помошники!)) Не назовете название той приспособы для хватания плит которой вы пользуетесь? Нужна реально. Пытались сделать самопальную, но что-то не так получилось - плиты выскальзывают , не держит вес
Marceneiro perigoso, não usa EPI, deixou o carro de transporte de chapa no corredor que estava caminhando bem no jeito de pisar ou tropeçar e sofrer um acidente de trabalho!
On a robland e3200 panel saw all final sizing of sheet materials ,ie crosscutting and ripping to size is done on the sliding carriage. It's a lot more accurate. The rip fence is only used for breaking down the sheets to near finished size before the final sizing on the carriage side .Hope this makes sense. When I bought the saw in 2006 the guy commissioning the machine said this was the way to use the saw. It's a little bit more time consuming but everything is extremely accurate coming off the saw. 15 yrs later and still 100% good. I'm not sure if this is the best way but it works for the robland e3200 .
Ese compa no tiene ni idea de como usar esa makina por eso es que tubo que dar esa bueltota para prenderla mejor no le de malas ideas a otras personas NO LENTES mi amigo le callo una hoja con esos sapatos en el pie y sabran en resultado.
La maquina en si es hermosa pero tiene graves imperfecciones por ejemplo la botonera de encendido y apagado, como es posible que el operario tenga que caminar de cuatro patas para encender la maquina, eso yo no lo tolero, yo fabrique una escuadradora y la botonera de encendido y apagado lo tiene en el carro y siempre esta a mano.
I have both of those tools for handling sheet good, though i put my wheels in the middle of the sheet. My wheels are a little different than your. Wider stance. I can actually let go and the sheet stay standing.
@@WOODMAN_pt Није сарказам, него шутка.🙂 Ја имам малу радионицу и почетак свског пројекта ми је размишљање како да урадим први рез кад плоча једва улази у радионицу.
la norma de seguridad donde quedan? comete error en levanta esa lamina sola .... deja la llanta ayudante en pocicion de realisar cortes ..da mucha weltas asta casi se cae acomodando los cortes..asta como que corta ladeada la lamina no en grado 90 para los conosedores y an cortado en este tipo de mesa escuadradora ....ojo te awevas y pierdes no el dedo ..la manoooo
Wow! That's a pretty large sheet of MDF. In the US, about all we can buy is 4' x 8' though allegedly, 10' sheets can be "specially ordered" but when I have tried, the answer is typically, "Oh, we're sorry, that's not available." Grrrrrrrrr.
Here, in Portugal, or let´s say in Europe as whole, it is standard size: 2750 1830 or 2800 x 2070.Therefore we look for these solutions.Our plywood or OSB standard size : 2500 x1250. In this case we use gorilla gripper.
Good job
I would have a lot of issues with the methods seen in this video and would not like if an amateur was to look at this as a proper guideline for operating a panel saw. Safety doesnt seem to be addressed in any way; the machine does not have a safety guard over the blade, and you can clearly be seen at 3.47 leaning in over the blade to retrieve the off-cut. Sheet material does not have an edge finish of adequate quality for most applications, so cutting datum edges would usually be the standard practice. I also would question the health and safety and the impact on quality of cut at 1.47 when you left the saw running in the incomplete cut, and again at 2.08 when the saw blade is distinctively louder due to the friction of it rubbing against the wood; a simple push through on the right hand side would solve this, and an outfeed table/roller would ensure the piece remains supported. Sorry to write an essay and criticise, I just think that there are far safer and better ways to use such a lovely machine!
+Patrick Kelly You are right if we take it the way how you´ve explained it. But the main idea was to show how I use special "helpers" to work on my own. but anyway thanks for your correct attitude to our profession. Rgds. Alex.
За@бали вы с такими тупыми комментами о безопасности.Я показал как возможно распилить такой лист одному, при помощи разных приспособлений.Вот и всё.
You are perfect ❤️👍
@@WOODMAN_pt😂😂
Вот так и я всё один таскал . До таскался((((( Уже девять месяцев не работаю Врачи категорически сказали не более пяти килограмм можно поднимать. Да что поднимать ходить долго не могу
Да, здоровье надо беречь.Держитесь !
١،عههه٤٧٧ع٧٥غ٥عا٦
wow another video on how NOT to use a sliding table saw . The number one safety instruction on these saws it stated right in the manual where it says " never use the crosscut fence in conjunction with the rip fence unless the rip fence is positioned to end just prior to the fron of the blade . using the two fences together can cause dangerous kickback
I've cut many huge Sheets on my own but dont work without a guard !!even worse when you video it absolutely no excuse or reason not to have a guard ,if you slip you fall on an exposed Blade ..why would you ??
One month later, i bought a proper guard for that machine. 2 years ago i bought proper Martin with a proper protection system.That was video only about helping equipment.
За@бали вы с такими тупыми комментами о безопасности.Я показал как возможно распилить такой лист одному, при помощи разных приспособлений.Вот и всё.
Тоже так сам карячусь ! А если МДФ 25 мм то уже тяжко )))
Это точно распиловщик?
Как можно у вас поработать? За сколько?
Я не хочу сказать, что всё хуёво, наоборот, мне очень понравилась скорость. Даже хромой справится в одиночку.
Моя мечта, работать в своё удовольствие, минимум физических нагрузок, за исключением подачи. 😁😁😁
Одна беда, при наших объёмах, за такую скорость, руководитель застрелит тебя из шуруповёрта или пневмо-ППШ.
Заморочек с подачей листа не понимаю, он замечательно подаётся по полу волоком, всё равно торцевать. Пирамида рядом...
Приспособление интересное, но хрен его кто рабочему человек купит😁. Проще самому сделать.
(Я себе моталку для стреча из октанрма и джокера сделал, чтоб не корячиться вниз головой мотая низ паллета)
Не холодно ли зимой?
Станок у ворот, сомнительное удовольствие.👍
У нас, в Португалии, всегда тепло.
Máy hay nhưng k biết bao nhiêu tiền làm mâyy1 tháng thì đủ tiền máy
Bhai is machine ka blood Kaise khulega an Ta Chita Ja tere mere ko bata do main apna WhatsApp number bhej raha hun
I never attempt to cut a whole panel om my panel saw, since it's just very difficult to manage, unless I absolutely have too. I break them down in smaller units with a track saw first.
Thanks for comment. But, as you can see, it is also possible to cut entire sheet without any big efforts. Frankly saying, it is not show off, just my standard procedure when I am alone in my shop.
check out 'thecrazyhorsedolly' on youtube for a solution.
Wuss
Your cutting skills or not enough.i will fire you in half day if you work for me.
Good to see your using the wheels to save your back from damage. Pity your not wearing a P3 mask for the mfd. The extract won't save u.
Gdzie jest formatowanie 🤔tniesz jak leci Oj tragedia 😞
as a woodmachinist of 40 years experience, I can say that is how not to do it
Человек оркестр) Хотя , в таком большом цеху обязаны быть помошники!))
Не назовете название той приспособы для хватания плит которой вы пользуетесь?
Нужна реально. Пытались сделать самопальную, но что-то не так получилось - плиты выскальзывают , не держит вес
+tusaund Модель: KFP от Bessey.bessey-shop.ru/product/derzhatel-dlja-perenoski-plit-kfp-bessey-be-kfp/
Manteve a serra ligada por 2,2 minutos, para utilizar apenas 15 segundos.
Laugh, i don't think i have ever had help on the panel saw. In all the shops i have worked in the panel saw was a 1 man opperation.
Marceneiro perigoso, não usa EPI, deixou o carro de transporte de chapa no corredor que estava caminhando bem no jeito de pisar ou tropeçar e sofrer um acidente de trabalho!
É perigoso morar no Brasil, principalmente em Favelas. Boa sorte meu amigo.
On a robland e3200 panel saw all final sizing of sheet materials ,ie crosscutting and ripping to size is done on the sliding carriage. It's a lot more accurate. The rip fence is only used for breaking down the sheets to near finished size before the final sizing on the carriage side .Hope this makes sense. When I bought the saw in 2006 the guy commissioning the machine said this was the way to use the saw. It's a little bit more
time consuming but everything is extremely accurate coming off the
saw. 15 yrs later and still 100% good. I'm not sure if this is the best way but it works for the robland e3200 .
Pineal saw cutter machine price in sharjah
Ese compa no tiene ni idea de como usar esa makina por eso es que tubo que dar esa bueltota para prenderla mejor no le de malas ideas a otras personas NO LENTES mi amigo le callo una hoja con esos sapatos en el pie y sabran en resultado.
Sólo es cuestión de tiempo para que sufra un accidente.
Gasta más luz que lo que corta, pierde mucho tiempo, el compa está muy verde para usarla ...
La maquina en si es hermosa pero tiene graves imperfecciones por ejemplo la botonera de encendido y apagado, como es posible que el operario tenga que caminar de cuatro patas para encender la maquina, eso yo no lo tolero, yo fabrique una escuadradora y la botonera de encendido y apagado lo tiene en el carro y siempre esta a mano.
Eso es correcto.
Dude, put the camera down and help.........Lol
It is the wife
its people like this is dislike (man) trying to show he can do everything on hes own , showing you he is better then you.
Nice one sir please keep it up
This is some of the worst cutting on a panel saw. didnt put a straight edge on it before the rip. didn't straight edge the dock i bet either
Before writing what you wrote you had to ask what was those panels I cut for !
За@бали вы с такими тупыми комментами о безопасности.Я показал как возможно распилить такой лист одному, при помощи разных приспособлений.Вот и всё.
That’s why they invented the track saw!
هذه الماركه من مناشير الشريوهات في اي بلد تصنع
السعر النهائي كام
What's the name of machine
Классные колеса 👍🏻
nice
دا كلام دا لو مصرى كان فرم رابطه فى نفس الوقت اوعه المصري
Bhai ji mere liye kam hai
Just goes to show you you can have really expensive equipment and not have a clue
بكام
What a fancy hugeee table saw 😍😍😍😍 nice video
This guy made it look much more difficult than it actually is.
Looks like he has no idea and its his first time or something lol
At least you know what you are writing.
Nice innovation. Which hand tool did you use to pull the sheet in the beginning ?
Thanks. Look for Bessey KFP panel carrier. th-cam.com/video/i9vdfSDHaj4/w-d-xo.html
I have both of those tools for handling sheet good, though i put my wheels in the middle of the sheet. My wheels are a little different than your. Wider stance. I can actually let go and the sheet stay standing.
Plz wear a mask , specially when cutting, routing , sanding mdf , beside that good video, God bless you..
necesariamente necesita una persona que le ayude así el muestre del par de el artilugio por decir que le hizo para desplazar la lámina
Ricardo O con una maquina asi cualquiera man
انا نجار من تونس عندى ديبلوم ابحث عن شغل
Very good and easy
That is a sliding table saw. Not a panel saw.
Changed.Many thanks for correcting. Appreciated.
/ Salaa
m
En lo que corta esa hoja yo corto díez jajajaja
Дамы и господа! В данном ролике вы увидели секс человека с листом МДФ! При съемках ролика ни один станок не пострадал!
Ye Kidar ka hii
machine address
Hou much price in india this machine
No se necesitan esos dispositivos para cortar una lámina al final se vuelven un riesgo para el que los utiliza,
Gracias por tu opinión.Saludos desde Portugal
How do i get one?
Price pls
Very nice set up
Good work
Hi
01876984157
Mai bhi yahi kaam kar raha hu sir 30%anubhaw hua hai .
Your next project: cutting mdf that starts from the middle of the street and the other end is in your workshop.
Спасибо Сербский Брат за сарказм.
@@WOODMAN_pt Није сарказам, него шутка.🙂
Ја имам малу радионицу и почетак свског пројекта ми је размишљање како да урадим први рез кад плоча једва улази у радионицу.
@@priscwy794frag instagram.com/p/B5LTGK8AVJi/?
@@priscwy794frag Я уже решал такую проблему.И уже давно купил другой станок.
How to preise
Hello good Morning.
devio de tener un colavorador de corte!
الراجل ده بطييييييء قوي
الرجل قوي جدا ودهن
como eu queria ter uma máquina dessas minhas condições é muito pouca
Faça o seu melhor e você vai ter.Com os melhores cumprimentos de Portugal. Carpentaria "WOODMAN"
الحمدلله
ايولي
Thank you. You should upload more on how to cut large sheet goods.
la norma de seguridad donde quedan? comete error en levanta esa lamina sola .... deja la llanta ayudante en pocicion de realisar cortes ..da mucha weltas asta casi se cae acomodando los cortes..asta como que corta ladeada la lamina no en grado 90 para los conosedores y an cortado en este tipo de mesa escuadradora ....ojo te awevas y pierdes no el dedo ..la manoooo
За@бали вы с такими тупыми комментами о безопасности.Я показал как возможно распилить такой лист одному, при помощи разных приспособлений.Вот и всё.
Wow! That's a pretty large sheet of MDF. In the US, about all we can buy is 4' x 8' though allegedly, 10' sheets can be "specially ordered" but when I have tried, the answer is typically, "Oh, we're sorry, that's not available." Grrrrrrrrr.
Here, in Portugal, or let´s say in Europe as whole, it is standard size: 2750 1830 or 2800 x 2070.Therefore we look for these solutions.Our plywood or OSB standard size : 2500 x1250. In this case we use gorilla gripper.
Woodman, take a look at my youtube vid 'thecrazyhorsedolly' or my website, thecrazyhorsedolly.com, and let me know what you think.
I am ready this job me follow
hahah ahhahaha hhaha...!!!
Que hermosa máquina!
какой формат листа вот в чем вопрос и сосояние дорожного покрытия
2800х2070х19, если что.(от Egger) но также пользуюсь и 2750х1830
Akele me parablam hota hai bhai
Right
Can anyone tell me how to buy this edge cutting machine, thank you!
You may find it on www.turanlar.com
@@enestuncdemir3289 toprağım
helal.olsun.
мая твая ни пaнимай
Согласен,проще чем у Калашникова)))
Потому что Калашников не ищет лёгких путей. :о)))
хотя плюс обязателен
Я. Вам, тоже лайк влепил. :о)))
A mí déjame tranquilo con la clásica Bidinost,no hay con que darle