I don't know if you will ever see this as your video was uploaded in 2016. God bless you for this video, I recently just got hired as technical support for this software and Neo products and this video has cleared up all the confusion i experienced after the training.
I do large jobs once in a while that require usage of this program. I always end up coming back to this video as a refresher on how to link up. Thank you!!
I am working my way through this video and setting up my new system. The DLS software would not communicate at first. I had downloaded from the link provided here. For those who also have this issue, be sure to go to HELP and then Update to get the latest version. After I did that, my software was at version 1.73 and I had no issues. So far this video has been very helpful and I am relieved that I can use my laptop to configure my system rather than the keypad.
If you don't have a NEO but a PC16** you need to go to the install menu section 499 (twice) at 4:22 in order for the panel to start downloading or uploading.
Excellent video and well thought out how all the info was presented!!! Thank you sharing and the time you put into this. I have an older DSC 632 panel PC1555MX PowerSeries but will use basically the same procedure as you presented. Of course, when I get to the *8 5555 code 403 & 404, I get binary number output, so had to decipher into real numbers and my numbers had 4 digits instead of 6 in your video. Again... your video was the best I found anywhere, to the point and easy to understand without all the techno-jargon of an authorized DSC Instructor. Thanks again!!!
Informative video, Thanks. Have Power Series for 20+ years or so and thinking of upgrading. System been running good. Just had to replace battery on sensor (2 time all these years). If I cant get my DLS2002 interface running again. I just may decide for the NEO and I think that uses DLS-5. I can program from keypad but helps to have the software. So far I was able to connect and upload but no actual data that I had printed years ago on the changes I made. Still working on it. Again Thanks and I will be back for more education.
Thanks! I find the video very useful. Managed to get it working remotely over IP! Next on my wish-list would be to see how firmware upgrades over PC-LINK or IP are done. Not sure I'm brave enough for those yet.
Do you need to interact with the Keypad and enter into Installer Menu 499, etc. like you need to with older Panels like PC5010 or does this accept the incoming connection automatically without Keypad intervention?
Hi, Thanks for the excellent video and detailed steps. I have a PC1832 panel with RFK5500 keypad, and I have problems getting the program to autodetect. Just wonder what I did wrong. Even as I tried specifying the panel ID and the keypad, the program seems having problems with the RFK keypad, and keep putting in 2 separate type keypad models instead of the RFK. Appreciate you can provide some insights to the problems. Thanks.
In programming section 13, system 1 options , the dialog box shows a choice of no end of line.....when I use my keypad... lcd. that option doesn't show. How to chose no eol using the keypad.
Please if you could help me, when connecting to the panel an error message appears as follows " unabla to start data mode with MCPH nothing " if you could help me with this I would be grateful.
Hello Automation guy I'm new at this...I have an 183200 dls panel I contected it to the Pc link...going well till DLS access code section / panel ID. When I enter section 403 or 404 it says "enter Hex data" then 183200 below for both...what is this and how can I overcome this section...?? Tks
If you haven't figured this out yet, the DLS access code and panel ID can be whatever you want at the end of the day, as long as they are each identical between the panel and the DLS software. Both fields are by default 183200 for your panel. Having that entered into both fields during setup should allow you to connect no problem
I have PC1832 it has only 4 pin female CON2 slot, is it the same PC link? I am not able to establish connection. I guess it is something else as on your board i see CON4 PCLINK1, CON5 PCLINK2 and CON2
Hello I bought a DSC NEO Outdoor PIR Motion Detector with Integrated Camera PG9944. Or have you already programmed PG9944, You have the experience to program to get the picture over Internet and HSPA Dual-path Alarm Communicator TL2803G to NEO GO App ? Thenks
Hi, this is great, thank you for uploading it.. Are you still going to create and upload another video about how to use the DSL 5 software? It would be great understand how it all works, and how you can provision your own system without needing to use a stock keypad.
Hello I have been able to connect to my panel using DLS and download the programing onto my computer but every time i try to send changes to the panel i get a communication error. Is there any option i need to set on my usa-19hs for it to work correctly? or any recommendations as of what might be the problem? any help will be appreciated. Thanks!
Hello i have a client that would like to monitor this panel via his cellphone. Is this something than can be done directly without the need of a monitoring company?
You can do it with Envisalink 4.it works with DSC. I used it with DSC1832.you can control your panel like arm, disarm and control Pgm. check the statut .you can also receive email notification .all of these staff are free.
nice video, i have a hs2032 neo and i want to manage over ip, using my smartphone, so i was thinking about tl280 but how i going to be the installation and software. thanks alot
Do you have any experience connecting to the Neo over IP? I have a HS2064, TL280R. I can connect to the 280 via DLS no problem if i just select Auto-> communicator. However if i try to add a panel i get this error "IP: The Panel Type HS2064 version 1.0 in the account did not match the panel type 0131 version 12 in the field." I have tried all the HS2064 panel options and they all yield this same result. If i Auto detect the panel it says it found HS2016, but then gives the same error. The sticker on the panel is a HS2064 so I am at a loss why it is saying the panels doesnt match.
is there programing software available for mac OSX? Do you work primarily with the DSC panels? Are there other hybrid systems available than do wireless and wired zones and have IP monitoring that you would recommend? Thanks in advance... and great videos by the way!
SO I bought the Keyspan USA 19HS as well as a new kit DB09 PC-Link Downloaded new software after deleting old and still nothing "Panel could not be Identified" Any thoughts at all Windows XP, no anti vius and no firewall running
i had the same issue and found out some of the pc link cables are reversed and was told to have the pc link circuit board above the pins on the panel instead of below and it worked for mine!
As long as you can connect to the panel via the DLS software (you'll need the panel ID code and DLS access code, which may be something other than default if you have a panel that was previously installed), there is a section for Master/Installer codes that you can view and edit as required, under "System" --> "Installer Options"
Think of zones as just sensors connected to your panel. Generally speaking each sensor would be a zone (wired, on the board itself, or wireless). Partitions are separate partitions/sections of a building or premise that can be armed and disarmed independently. For example you may have a factory with a single panel. One partition can be the production area with its own keypad. The other partition can be the office section with its own keypad. Production area can be armed while the office area is disarmed. Or office can be armed while production is disarmed. I hope this clarifies your question.
Thanks for the reply, I actually downloaded all of my information. I then made a lot of adjustments and tried to upload and now I cant connect at all. Could the cable be bad?
Just check your drivers for your serial adapter. Make sure its install and the computer see it. Maybe try a different USB Port (or a system reboot). When you are trying to load to the panel. Try sending the file, (instead of going into programming to initiate the panel ) Just unplug the pc-link from the panel then plug it back in. See if the progress bar moves.
So I tried all above including removing software and reinstalling it. Could it be the adapter is bad as my computer sees the Belkin USB to serial adapter and gives it a comm port so I'm at a loss and will just buy another adapter. If you have any other thoughts I would appreciate your input
Hi "The Automation Guy", due to I dont know your exact name, sorry for calling you with your nick. Sir, I am still unable to install DLS5 V1.71 (INT) to my PC with Windows 10 release 1909(latest). My question is what are the prerequisities and procedures BEFORE INSTALLING DLS5. Your timely support will be most appreciated. Many thanks in advance.
Figured maybe I’d ask someone else who’s used this software. So all is good until I finished programming everything, basically the software is telling me a ton of stuff isn’t programmed when it is it tells me to fix errors but when I download from panel to pc says all is good, I goto download that same into from pc back to panel and says enter valid info, when it’s been valid and is valid
Hi @TheAutomationGuy I would like to ask you if you can somhow show us how to programm Account Code! If channel is still active! This vid! is super usefull to me because I'm gonna soon buy DSC 128 Zone Panel and I would like to install by myself cuz' Installer want's to charge me of up to $400-$500 for installation! 🤔 Thank you in advance!
Hi everybody, whatever I tried to run DLS V program on Windows 10, unfortunately all my attempts were invain and I failed. And DLS V program never been installed. Is there anybody to run this program on windows 10, please help me how to. Many thanks
I don't know if you will ever see this as your video was uploaded in 2016. God bless you for this video, I recently just got hired as technical support for this software and Neo products and this video has cleared up all the confusion i experienced after the training.
I do large jobs once in a while that require usage of this program. I always end up coming back to this video as a refresher on how to link up. Thank you!!
I am working my way through this video and setting up my new system. The DLS software would not communicate at first. I had downloaded from the link provided here. For those who also have this issue, be sure to go to HELP and then Update to get the latest version. After I did that, my software was at version 1.73 and I had no issues.
So far this video has been very helpful and I am relieved that I can use my laptop to configure my system rather than the keypad.
Straightforward presentation and very informative on the important points. Thank you for posting.
I watched almost all your videos for dsc. You have done great job. I am waiting for your next videos
Thank you.
If you don't have a NEO but a PC16** you need to go to the install menu section 499 (twice) at 4:22 in order for the panel to start downloading or uploading.
Excellent video and well thought out how all the info was presented!!! Thank you sharing and the time you put into this. I have an older DSC 632 panel PC1555MX PowerSeries but will use basically the same procedure as you presented. Of course, when I get to the *8 5555 code 403 & 404, I get binary number output, so had to decipher into real numbers and my numbers had 4 digits instead of 6 in your video. Again... your video was the best I found anywhere, to the point and easy to understand without all the techno-jargon of an authorized DSC Instructor. Thanks again!!!
Were you able to get this to work with dls5 and the pc1555mx? I'm having some trouble.
Informative video, Thanks. Have Power Series for 20+ years or so and thinking of upgrading. System been running good. Just had to replace battery on sensor (2 time all these years). If I cant get my DLS2002 interface running again. I just may decide for the NEO and I think that uses DLS-5. I can program from keypad but helps to have the software. So far I was able to connect and upload but no actual data that I had printed years ago on the changes I made. Still working on it. Again Thanks and I will be back for more education.
Great video, thanks. I am used to doing the programming from the keypad only, so the software walk through is very helpful.
Thanks! I find the video very useful. Managed to get it working remotely over IP!
Next on my wish-list would be to see how firmware upgrades over PC-LINK or IP are done. Not sure I'm brave enough for those yet.
lol. If i get some time in the upcoming week i will make a video for upgrading the firmware. I haven't played with the IP communicator.
Do you need to interact with the Keypad and enter into Installer Menu 499, etc. like you need to with older Panels like PC5010 or does this accept the incoming connection automatically without Keypad intervention?
Any video on TL280LE(R) Programming ?
I have the TL280RE Internet Alarm Communicator, can that connect to dls5 with internet via ip connectivity or is it strictly serial
Do you need the PC link for DLS if you're using a TL280RE?
Hello, how do I change the input and output times in the Neo control panel with the DLS5
Plz share the manual or any video to understand the Installation and Configuration
Hi, Thanks for the excellent video and detailed steps. I have a PC1832 panel with RFK5500 keypad, and I have problems getting the program to autodetect. Just wonder what I did wrong. Even as I tried specifying the panel ID and the keypad, the program seems having problems with the RFK keypad, and keep putting in 2 separate type keypad models instead of the RFK.
Appreciate you can provide some insights to the problems. Thanks.
@the automation guy please explain how to solve link fault
Where do I download the DSL 5 software can I get the link please
In programming section 13, system 1 options , the dialog box shows a choice of no end of line.....when I use my keypad... lcd. that option doesn't show. How to chose no eol using the keypad.
Super video, but must you not first ENABLE DLS for DLS to work ? I am not sure ? using *6 master code - 5 ?
Please if you could help me, when connecting to the panel an error message appears as follows " unabla to start data mode with MCPH nothing " if you could help me with this I would be grateful.
Is there a doc out there that gives a better description of all of the panel options. Some are very vague
Yes but how to you get the DLS software. It seems that you have to be a professional installer registered with DSC in order to download the software.
Hello Automation guy I'm new at this...I have an 183200 dls panel I contected it to the Pc link...going well till DLS access code section / panel ID. When I enter section 403 or 404 it says "enter Hex data" then 183200 below for both...what is this and how can I overcome this section...?? Tks
If you haven't figured this out yet, the DLS access code and panel ID can be whatever you want at the end of the day, as long as they are each identical between the panel and the DLS software. Both fields are by default 183200 for your panel. Having that entered into both fields during setup should allow you to connect no problem
Hi Sir. Could you kindly do a video on how to Program the Tl280(e) and Tl280(3G)for home use.
How do you get the panel id if you don't have a message keypad and just a fixed number keypad.
I have PC1832 it has only 4 pin female CON2 slot, is it the same PC link? I am not able to establish connection. I guess it is something else as on your board i see CON4 PCLINK1, CON5 PCLINK2 and CON2
Hello
I bought a DSC NEO Outdoor PIR Motion Detector with Integrated Camera PG9944. Or have you already programmed PG9944, You have the experience to program to get the picture over Internet and HSPA Dual-path Alarm Communicator TL2803G to NEO GO App ?
Thenks
Hi, this is great, thank you for uploading it..
Are you still going to create and upload another video about how to use the DSL 5 software?
It would be great understand how it all works, and how you can provision your own system without needing to use a stock keypad.
can you guide me this error on keypad *2 device tampers zone 11 , device is PG4914
Hey i get the Cable but i need the software to program it
Hello I have been able to connect to my panel using DLS and download the programing onto my computer but every time i try to send changes to the panel i get a communication error. Is there any option i need to set on my usa-19hs for it to work correctly? or any recommendations as of what might be the problem? any help will be appreciated. Thanks!
Excellent demo, thank you sir!
I have a DSC pc1832 v4.2. Does the DLS 5 software work to program my panel ?
yes
@@MBoczula : Hi Mateusz, do you have the connection with female terminal on DSC PC1832?
Awesome Videos! They helped me with an issue I was having and can now fix it!
Very helpful! Where do I find the System Account Code?
Hello i have a client that would like to monitor this panel via his cellphone. Is this something than can be done directly without the need of a monitoring company?
The only option I know is Alarm.com and it has a monthly fee. DSC has a partnership with alarm.com.
You can do it with Envisalink 4.it works with DSC. I used it with DSC1832.you can control your panel like arm, disarm and control Pgm. check the statut .you can also receive email notification .all of these staff are free.
nice video, i have a hs2032 neo and i want to manage over ip, using my smartphone, so i was thinking about tl280 but how i going to be the installation and software. thanks alot
Would so love if you can do a full video of how to program the (TL280E) from the keypad in section (851) would really appreciate it
Do you have any experience connecting to the Neo over IP? I have a HS2064, TL280R. I can connect to the 280 via DLS no problem if i just select Auto-> communicator.
However if i try to add a panel i get this error "IP: The Panel Type HS2064 version 1.0 in the account did not match the panel type 0131 version 12 in the field." I have tried all the HS2064 panel options and they all yield this same result. If i Auto detect the panel it says it found HS2016, but then gives the same error.
The sticker on the panel is a HS2064 so I am at a loss why it is saying the panels doesnt match.
ever figure this out?
is there programing software available for mac OSX? Do you work primarily with the DSC panels? Are there other hybrid systems available than do wireless and wired zones and have IP monitoring that you would recommend? Thanks in advance... and great videos by the way!
How do DIY's get the DLS 5 software??
can you do a video programming the Share this page on
HSPA Dual-Path Alarm Communicator
TL2803G(R)(E) via the dls software
Does your laptop have to be plugged into the control panel, or it uses wifi to get the panel info?
It plugs into the pc link
SO I bought the Keyspan USA 19HS as well as a new kit DB09 PC-Link
Downloaded new software after deleting old and still nothing "Panel could not be Identified"
Any thoughts at all Windows XP, no anti vius and no firewall running
i had the same issue and found out some of the pc link cables are reversed and was told to have the pc link circuit board above the pins on the panel instead of below and it worked for mine!
I like this channel, I think you deserve 100k subs. I subscribed
Thank you.
+The Automation Guy Your welcome
I have a HS2016 V1.13 and TL2803G(R) V4.1 may i know how does the DLS 5 software work to program my panel ? TQ
ever figure this out?
Dear Sir. Please, maybe you can tell where to download this software?? but not to be at DSC web site
www.dropbox.com/s/wzdnwmwmlf2zjbi/DLS5-NA.exe?dl=0
Very helpful video. Thank you. Hope you make some more videos with more in depth training.
I will soon. Thank you
where do you get the account code from?
I work for a company, every customer has different account, so they give me the account number to set it up to the board. I hope I helped
Это видео очень помогло, спасибо вам за вашу работу.
Hi where do you get the software from?
Is there a way with this software to get the installer code? If so how do I get it ?
As long as you can connect to the panel via the DLS software (you'll need the panel ID code and DLS access code, which may be something other than default if you have a panel that was previously installed), there is a section for Master/Installer codes that you can view and edit as required, under "System" --> "Installer Options"
Your videos are great, thanks for your input
i just want to know the difference between zones and partitions...
I could explain it to you however i'd hate to not be clear. Would you rather me do a quick video to explain?
Think of zones as just sensors connected to your panel. Generally speaking each sensor would be a zone (wired, on the board itself, or wireless). Partitions are separate partitions/sections of a building or premise that can be armed and disarmed independently. For example you may have a factory with a single panel. One partition can be the production area with its own keypad. The other partition can be the office section with its own keypad. Production area can be armed while the office area is disarmed. Or office can be armed while production is disarmed. I hope this clarifies your question.
Where do I download this from? DSC requires registration, fill in the application...
www.dropbox.com/s/wzdnwmwmlf2zjbi/DLS5-NA.exe?dl=0
Keeps saying the panel cant be identified? Any thoughts
Try creating the file based on the version on the green sticker. I have seen this issue when doing auto-identify.
Thanks for the reply, I actually downloaded all of my information. I then made a lot of adjustments and tried to upload and now I cant connect at all. Could the cable be bad?
I tried again and no luck all I get is Link is green and RX flashes red no TX
Just check your drivers for your serial adapter. Make sure its install and the computer see it. Maybe try a different USB Port (or a system reboot).
When you are trying to load to the panel. Try sending the file, (instead of going into programming to initiate the panel ) Just unplug the pc-link from the panel then plug it back in.
See if the progress bar moves.
So I tried all above including removing software and reinstalling it. Could it be the adapter is bad as my computer sees the Belkin USB to serial adapter and gives it a comm port so I'm at a loss and will just buy another adapter. If you have any other thoughts I would appreciate your input
Do you actually use this system in your house? If so, who do you have for your monitoring company?
Yes, I do I work for a company and I use their monitoring company. Cops monitoring
Hi "The Automation Guy", due to I dont know your exact name, sorry for calling you with your nick. Sir, I am still unable to install DLS5 V1.71 (INT) to my PC with Windows 10 release 1909(latest).
My question is what are the prerequisities and procedures BEFORE INSTALLING DLS5. Your timely support will be most appreciated. Many thanks in advance.
If i set section 403 than I've signal from keyboard like it'd be a wrong number.
I don't know why... I can't solve this :( I tried 403 and 499...
great video cant seem to find the software anyware can any buddy help thanks keep up the good videos
Great video... Thanks for that!
Very helpful. Thank you.
Thank you. this was great help
very nice presentation!
Figured maybe I’d ask someone else who’s used this software. So all is good until I finished programming everything, basically the software is telling me a ton of stuff isn’t programmed when it is it tells me to fix errors but when I download from panel to pc says all is good, I goto download that same into from pc back to panel and says enter valid info, when it’s been valid and is valid
Awesome, thank you…. :)
Excellent video! I'm ready to install one for free!
Great video! Thanks a lot!
Hi @TheAutomationGuy I would like to ask you if you can somhow show us how to programm Account Code! If channel is still active! This vid! is super usefull to me because I'm gonna soon buy DSC 128 Zone Panel and I would like to install by myself cuz' Installer want's to charge me of up to $400-$500 for installation! 🤔
Thank you in advance!
thanks, very helpful
Thanks. And now to water board my adt tech for the installer code lol
Good luck with that!
Prem from Jodhpur Rajasthan India
Hi everybody, whatever I tried to run DLS V program on Windows 10, unfortunately all my attempts were invain and I failed. And DLS V program never been installed. Is there anybody to run this program on windows 10, please help me how to. Many thanks
excelente youtuber
Presentation great- audio level a bit low
Great video
You are awesome
This is awesome!
Why can't I see the replys
Thanks
Hi
I have 4020pc will this work on DLS 5? I’m using DLS 2002 to download..