Thank you very much for the video helped get me started. Would like to add that it is possible to replace the bearings without burning the whole clutch. The bearings are nachi 6006-2nse9. The exact match of what's in there is no longer. The only tricky part is rigging a jig to hold the large spring compressed while tapping on the bearing.
Good ? My friend the truth is this clutch has a lock on them the bearings can't be replaced only the Warner clutch my 14sb is the first yr made 1989 they where made with the 1 piece urgura clutch the bearing were not ment to be replaced where the bearing is at there are 2 bent clips 1 on 1 side 1 on other and it is part of the steel body of the clutch LOCKED can't be bent to take out the bearing must buy a new clutch to replace the bad one good luck in finding a new one for there now over 35 yrs old and Discontinued. Be careful on burying used on ebay big job to take out and put In then to find out the one from ebay is just as bad or worse then yours was 🙏
@@TonysLawnCare215 my mower is a14 PB. I believe I bought it in 91. The bearings are in the old clutch and working fine. The bottom bearing is a pressfit and the top one which was bad, is held in by a snap ring and three bent tabs on the outer housing. Ground the tabs off the Dremel.
Tony need your help. I have a 14SB, recently my brake clutch to engage the blade will not stay forward at all times (sometimes it stays forward sometimes it pops back) is there an adjustment?
@@AdamKinard-er7uw Adam there is no other thing that can make that happen then your Brake leaver handle is worn o don't believe there is a way to adjust it it is just worn out time did that NOT A. BIG. DEAL go to Fleabay I mean ebay lol and buy another one sorry I did not have good news for you on adjusting it .just has to be replaced Fleabay is your best options to find it . Let me know how it goes
I found a used Oruga clutch for my 14SB for $28 in good condition, I cannot find a 14 M course thread bolt to remove the Warner clutch. I got a 14 mm bolt course thread but it won’t work, any advice?
How do you know it is in good condition when you never installed it yet ? just that it looks clean does not mean it is in good/ Great condition Untill you put it on then listen to the sound hopefully it spins quiet not a screaming sound Good luck taking off the spring and putting it back on for me it was a pain in the ass you knead a helper to hold the spring i used a rubber band as in my install video th-cam.com/video/C5ZWvbqOkh8/w-d-xo.html
![เปิดใจ "อาจารย์เบียร์ คนตื่นธรรม" อดีตเคยสุดทุกทาง ถ้าใช้หนี้หมดไปบวชแน่ l [Nickynachat]](http://i.ytimg.com/vi/IxeE0xVhy08/mqdefault.jpg)
Thank you very much for the video helped get me started. Would like to add that it is possible to replace the bearings without burning the whole clutch. The bearings are nachi 6006-2nse9. The exact match of what's in there is no longer. The only tricky part is rigging a jig to hold the large spring compressed while tapping on the bearing.
Good ? My friend the truth is this clutch has a lock on them the bearings can't be replaced only the Warner clutch my 14sb is the first yr made 1989 they where made with the 1 piece urgura clutch the bearing were not ment to be replaced where the bearing is at there are 2 bent clips 1 on 1 side 1 on other and it is part of the steel body of the clutch LOCKED can't be bent to take out the bearing must buy a new clutch to replace the bad one good luck in finding a new one for there now over 35 yrs old and Discontinued. Be careful on burying used on ebay big job to take out and put In then to find out the one from ebay is just as bad or worse then yours was 🙏
@@TonysLawnCare215 my mower is a14 PB. I believe I bought it in 91. The bearings are in the old clutch and working fine. The bottom bearing is a pressfit and the top one which was bad, is held in by a snap ring and three bent tabs on the outer housing. Ground the tabs off the Dremel.
Tony need your help. I have a 14SB, recently my brake clutch to engage the blade will not stay forward at all times (sometimes it stays forward sometimes it pops back) is there an adjustment?
@@AdamKinard-er7uw Adam there is no other thing that can make that happen then your Brake leaver handle is worn o don't believe there is a way to adjust it it is just worn out time did that NOT A. BIG. DEAL go to Fleabay I mean ebay lol and buy another one sorry I did not have good news for you on adjusting it .just has to be replaced Fleabay is your best options to find it . Let me know how it goes
I found a used Oruga clutch for my 14SB for $28 in good condition, I cannot find a 14 M course thread bolt to remove the Warner clutch. I got a 14 mm bolt course thread but it won’t work, any advice?
How do you know it is in good condition when you never installed it yet ? just that it looks clean does not mean it is in good/ Great condition Untill you put it on then listen to the sound hopefully it spins quiet not a screaming sound Good luck taking off the spring and putting it back on for me it was a pain in the ass you knead a helper to hold the spring i used a rubber band as in my install video th-cam.com/video/C5ZWvbqOkh8/w-d-xo.html
Need a clutch! My is a screamer and is now slipping