TIP YOU NEED TO KNOW! if you making DIY Gaming Steering Wheel (Important). Be sure to watch. th-cam.com/video/7EY1GpAGPck/w-d-xo.htmlsi=PEOsDiciiBHmt72X
Bro i tried Uno at First Too i tried it with Uno joy and Encoder but no its not working you cant Upload the Firmware for the Software rfr Wheel configuration on the uno because it has a different Chip so it isnt possible and you have no Force Feedback wich means you have no center spring or degree lock for example 900 degree lock wont work so not worth it buy Leonardo instead
Hi, why is this build do not works with other arduinos? I am planning to build something similar, and collecting ideas. I plan to do it with something stronger than an arduino, maybe an ARM. Or maybe the pc program can only use arduino leonardo?
We use wheelconfig software to use this. This software supports only arduino leanardo. But I have seen some people make it from other program boards. But I don't really know much about it.
Bro you can use a board like Arduino but have more performance called stm 32 They usually use it in direct wheel drive project search about it it would be more helpful❤@@katogergo4710
Hello kind sir, i have problem. when i press "center wheel" instead of it centering the wheel, it goes fully left on the axis (No ffb) and does not go past its actual center
@@king_h.3826 @king_h.3826 Yes iam from india but if i use two motors and two motor driver then it will produce more heat and it is good if it will produce more rpm then the feeback will be strong
bro you are amazing and fantastic, i love your concept and videos but plz also provide parts links that you use in video. because out there are lot of same product that dont work same. Thank you man. i appreciate your work. and also how much total cost for only wheel in this video if i use everything you use.
I bought a lot of parts from our local market (Sri Lanka) and online market prices are very different so that's why I didn't upload the links. And I randomly calculated from Aliexpress it is close to 50$ USD.
Hey, I had a doubt, if I am using an arduino Leonardo instead of a controller’s board can I use 5 analog inputs (steering, gas, brake, hand brake, clutch) because the arduino has 6 analog inputs available right ?
Man i cant find these pulley teeth on internet and (offline) either its too expensive (like 4k rs) or unavailable what should i do or can you say where did you buy from
can u use a mouse sensor ?? for rotation detection ? converting a rotation motion to linear motion and then converting it into a angular motion by using geometric functions as a high DPI mouse can detect a linear displacement so aacurate and precise so that the cost can be reduced, we can increase its effeicency more than 600PPR
this project uses an "NPN open collector output type" encoder so we have to use ''INPUT_PULLUP'' inputs or ''external pull-up'' resistors. that's why I am using 10k resistors. Basically, if we don't use resistors, the wheel is completely not working
hello there are multiple versions of the dc motor that you showed, so i wanted to know how many newtonmeters of torque you reccomended, is 1 enough or do i need more?
I'm thinking of changing the motor into a nema 34 100 mm to get 6 Nm torque, what do you suggest in choosing the encoder and the motor driver? (Moza R5 is too expensive 😢)
I see this motor has great power but I actually don't know if is it compatible with this project. btw you can try a MY1016 motor. I think that's a great motor for this.
Hello bro, I was looking at the diagram and pins 7 and 8 are not connected. Could two more buttons be connected there? And assign them in the program? Since they are not being used and I would like to place more buttons for other actions
@@zudumalli I installed the buttons on Pins A, but they did not work, instead I installed them on Pins 7,8 and 9 and managed to obtain more actions with three more buttons
Can i use a power supply of 12v 5amp because I am using only steering and gas and brake along with ffb ( I don't need Padal shifter or h shifter )😊and can i use a laptop adapter of 12v without power supply
Can i replace the motor driver with DC controller Because i have DC motor that have very high torque but it can't connect to motor driver but it can connect to DC controller
Which software are you using, and does it support steam games like f1. If possible, can you explain how ardunio is connected to pc to detect it as a gamepad. Mostly software side of the build. Thanks 😊
![DIY Force Feedback Steering wheel | FFB Sim Racing wheel | Arduino Drifting wheel[ENGLISH tutorial]](http://i.ytimg.com/vi/6pEiYvWLGJ4/mqdefault.jpg)
TIP YOU NEED TO KNOW! if you making DIY Gaming Steering Wheel (Important). Be sure to watch. th-cam.com/video/7EY1GpAGPck/w-d-xo.htmlsi=PEOsDiciiBHmt72X
Can we use a ebike motor
Can you provide the code you used? Not the hex
Can I get that products buying link
Hi, I wanted to know if I can find any steering wheels for cheap instead of making it with cardboard
Waiting for next video.❤️😋.this is the best video ❤.from 🇱🇰 😊
🥰🥰
why we can't use arduino uno, i have uno can we able to make without ffb. any idea
Bro i tried Uno at First Too i tried it with Uno joy and Encoder but no its not working you cant Upload the Firmware for the Software rfr Wheel configuration on the uno because it has a different Chip so it isnt possible and you have no Force Feedback wich means you have no center spring or degree lock for example 900 degree lock wont work so not worth it buy Leonardo instead
@@bossoy0769 got it thanks buddy
U can make a wheel without ffb with uno but it is not that good
@@gl1tch286 with uno r1 right?
NINTENDO HIRE THIS MAN
Please don't
Let this person be free to make their inventions available to everyone.
this is what all i need formerly, thanks bro, you so helpful for me
Glad to hear that! thans man
maram koliti me video ekat patta😀👍
❤❤
@@zudumalli 👍
Great video, all the other ones lack the details in yours, thank you so much, you helped me a lot.
You're very welcome!
Hi, why is this build do not works with other arduinos? I am planning to build something similar, and collecting ideas. I plan to do it with something stronger than an arduino, maybe an ARM. Or maybe the pc program can only use arduino leonardo?
We use wheelconfig software to use this. This software supports only arduino leanardo. But I have seen some people make it from other program boards. But I don't really know much about it.
@@zudumalli okay thanks for the answer, i am gonna do a little bit more research
Bro you can use a board like Arduino but have more performance called stm 32
They usually use it in direct wheel drive project search about it it would be more helpful❤@@katogergo4710
So could i have more power with 2 dc Motors one 775 and the other one 550 motor?
Yes, no problem
Will this work with h shifter, pedals, and handbrake
yes
bro can we use potentiometer instead of encoder without fbb if possible there will be any deadzone issues
no, the potentiometer doesn't support FFB
Hello kind sir, i have problem. when i press "center wheel" instead of it centering the wheel, it goes fully left on the axis (No ffb) and does not go past its actual center
Can i use 2 rs 775 motors please
And where to connect it with wire anwer
I am thinking of the same project bro, with two motors
yes @King_ h was right.
Should i use 895 motor instead of 2 775's
@@Daksh_yadav20 rpm is too high and it will heat more. Also if you are from India, here 775 is cheaper compared to 895.
@@king_h.3826 @king_h.3826
Yes iam from india but if i use two motors and two motor driver then it will produce more heat and it is good if it will produce more rpm then the feeback will be strong
bro you are amazing and fantastic, i love your concept and videos but plz also provide parts links that you use in video. because out there are lot of same product that dont work same. Thank you man. i appreciate your work. and also how much total cost for only wheel in this video if i use everything you use.
I bought a lot of parts from our local market (Sri Lanka) and online market prices are very different so that's why I didn't upload the links. And I randomly calculated from Aliexpress it is close to 50$ USD.
නියම වැඩක්👍.great
😍😍❤
How many rpm, should be these dc motor (I want to choose rs775)?
RPM doesn't much matter, you need large torque. if you don't understand watch this video th-cam.com/video/7EY1GpAGPck/w-d-xo.htmlsi=93VRqvpIQERDKRAl
Hey, I had a doubt, if I am using an arduino Leonardo instead of a controller’s board can I use 5 analog inputs (steering, gas, brake, hand brake, clutch) because the arduino has 6 analog inputs available right ?
No bro, the Arduino has six analogs, but the software supports only four analogs.
You can use emc utility
@@zudumallifour? Then you can use clutch brake acc and handbrake?
@@RealRenkothen the steering
is it possible to use a DC motor type 550 at 14.4 volts?
Yes you can but the torque is quite low
@@zudumalli So I'd better order a new motor.
thank you for responding to comments even after such a long time))
What RPM motor would be the best?
What resistance potentiometer would be best for the pedals?
10k
What is the resistors in the encoder system for? And can they be of less or more resistance?
Yo bro your videos are so cool, if i use the console controller thing does that mean that i can hook it up to an Xbox or playstation via usb?
Can i use a slim power supply
Bro did u use the same bracket for 775 dc motor and encoder
yes, but I made extra holes for the encoder
can you make no ffb but still using Arduino
Where did you buy those stuff?
bro can we use copy or clone arduino leonardo.
Yes I have a Clone Aswell it just needs the atmega32u4 Chip
@@bossoy0769 thanks bro
how to do the paddle shifters??????
Is this steering wheel is better than pxn v3 ? And v3 pro
Bro please tell me how can i buy it please ❤❤😢 i dont want the new one give me the old one itself
I don't have it now bro
Was it working? After using for a time?@@zudumalli
Hello can i apply that for the pxn v9
the software? - I actually don't know but if you have the wheel you can try it
Did you have another motor burn out after installing the fan?
no
Great video, will this work with Leonardo R3 board?
Yes it will
is thread bar can be thinner ?
No, if that happens, the strength is not enough
@@zudumalli thans
are the mounting brakets nesesary
It helps to stronghold your motor and keep the belt straight (that's important to provide great ffb). if you have another way, you can try it.
Which side is positive negative in dc motor 775
The positive side is marked in red color.
3:52 How to add the second motor in same motor driver because in the second slot power supply and fans are connected
I really like your content
both motors are connected in parallel and connected to the motor slot of the BTS driver.
Can you make a video about it please or explain briefly steps
Can i buy second motor driver and connect it to same gnd pin and different pwm
Will emc support it ?
Can i use potentiometer or it must be encoder
Next video
Man i cant find these pulley teeth on internet and (offline) either its too expensive (like 4k rs) or unavailable what should i do or can you say where did you buy from
yes, it bit expensive. I live in Sri Lanka bro I bought it from our local market. btw maybe you can find it from Aliexpress.
@@zudumalli AliExpress is banned in India and btw I found it all in 459 rs and I think it's quite cheap
Is there any way I can connnect the wheel to my switch consol?
In this way, a box can be prepared and connected easily.
th-cam.com/video/IiGNMv1sxj8/w-d-xo.htmlsi=r5qsw5iYMDT0w2tb
Whats the k of potentiometer??????
10k
amazing work bro 💖also voise is lovely 😁
Thanks 😅
When I am connecting button and I press it. My wheel Center messes up and rotary encoder isn’t working for a while. What can I do?
check your wiring maybe there is a short circuit
@@zudumalli hey I checked it. But when I use the wheel rotary encoder isn’t stable? The center moves tiny bit every time i use the wheel
Is it possible to play mudrunner/snowrunner?
yes
@@zudumalli can you make a video on that
Bro how much force u got like 20n or 30n?
can u use a mouse sensor ?? for rotation detection ? converting a rotation motion to linear motion and then converting it into a angular motion by using geometric functions as a high DPI mouse can detect a linear displacement so aacurate and precise so that the cost can be reduced, we can increase its effeicency more than 600PPR
Bro what is the use of z switch
To turn on the encoder. In some cases it has to be turned off for calibration.
can we use 1000ppr rotatory encoder?
if yes then changes we should do
Yes you can. Nothing changes
Thanks man
can i use a 3 phase rotary encoder????
if yes how
no bro this supports only 2 phase encoders
Can i swich the h shifter ground to above one?
yes
How it detected in PC? Like gamepad in controler device or its like usb? I mean if it detected like gamepad in device manager i can callibrate it
Major improvement, does this work for console?
No😐
Bro what is the size of wood you use in this built
0.75 inch
can u still use 5 amps or 60 watts
no. I haven't used 5 amps. this needs 12v 15 or 20 amps.
@@zudumalli well i think it can be 5 amps since its only for the DC MOTOR not for the others but thanks
Bro can we use 12v 5a smps power supply
not enough
bro where to buy gears in online
aliexpress
can I apply 14-15 volts to the motor driver board
It can use up to 27v
@@zudumalli thank you very much, I will also collect it when the encoder arrives
Which power supply do I need for one RS 550 motor?
Did you use any software to use this in gta V of forza and how does the sterring wheel comes in 0 degrees did you setup that.
I have uploaded a video on how to play Forza and GTA v
I have a question, why would you need to connect a resistor from the postive terminal to channel 1 and 2 of the rotary encoder?
this project uses an "NPN open collector output type" encoder so we have to use ''INPUT_PULLUP'' inputs or ''external pull-up'' resistors. that's why I am using 10k resistors. Basically, if we don't use resistors, the wheel is completely not working
Can i use a pro micro? It's has a atmega32u4 chip like the leonardo board
i already have a steering wheel i just want to add force feedback to it is it possible?
yes you can use Arduino and rebuild it
Bro what shop you buy parts from some parts I cant find help I am in colombo
Some parts are purchased from Nugegoda Tronic lk. The encoder purchased from aliexpress.
@@zudumalli thanks i got my encoder from there it was only 3500rs
hello there are multiple versions of the dc motor that you showed, so i wanted to know how many newtonmeters of torque you reccomended, is 1 enough or do i need more?
One motor is enough for me. It depends on the size of the pulley and steering wheel you are using. But I also install another motor in the future.
Will the diy steering wheel work on Nintendo switch
I don't know about that
I'm thinking of changing the motor into a nema 34 100 mm to get 6 Nm torque, what do you suggest in choosing the encoder and the motor driver? (Moza R5 is too expensive 😢)
I see this motor has great power but I actually don't know if is it compatible with this project. btw you can try a MY1016 motor. I think that's a great motor for this.
Ooh okay thanks. How about the encoder, the motor driver, fan, and the power supply? What should I choose?
Can it be made to use with PS4?
Bro wich power supply Are you using ? 12v or 24?
12v but I will buy 24v in future
@@zudumallihow much amperage does your power supply have?
Hello bro, I was looking at the diagram and pins 7 and 8 are not connected. Could two more buttons be connected there? And assign them in the program? Since they are not being used and I would like to place more buttons for other actions
no you can use A3, A4, A5 (analog side)
@@zudumalli I installed the buttons on Pins A, but they did not work, instead I installed them on Pins 7,8 and 9 and managed to obtain more actions with three more buttons
can i use a 500mm belt?
yes
Bro can I use 12v 30a smps power supply
Yes you can
can i skip the belts and make it direct drive? what i lose if i make it direct drive?
You lose the torque. Watch my last video I explained this
can i use a motor with encoder
yes
@@zudumalli thanks
Broo can we use db9 connectors instead of rj45 connectors
yes of course
Hi bro i had some problems like my motor doesnt work when connected to bts7986 and arduino
Bro what's tha name of sticker paper you use . ??
It's a car wrap sticker. I don't know what the name is.
wiring diagram for dual motor?
I'm curious why the wiring is different from the 'Tech at Home's DIY steering tutorial. Maybe that's for EMC, yours is for AI WAVE?
Wiring is different due to firmware
Aluminum pulleys & xl belts ganna place ekak dannawada in sl?
Also 600ppr encoder gathe kohenda?
Pulleys gatthe nugegoda tronic.lk eken. Encoder eka gatte aliexpress eken.
hi i wanted to know if your firmware works on the stm32 board
no
What is the rating of power supply
like 450w
Is 12v 5a supply enough?
No 12v 20A or 24v 5A
Hi, how much cable do i need?
20-25 jumper wires and 16-way ribbon wire (enough for wheelbase only)
if i want to use two 775 motor in parallel, how many Volt and Amp smps should i buy?
you can use 24V 2.7A (65W) power supply
Bro from where you are
Can you make it for me under budget 3k
I am from Sri Lanka.
I will explain how to do it on a low budget in the future
Hey, I’m worried about using a dc motor… is it not going to result into a short circuit
No, that will not happen
funciona con el Arduino UNO?
No
😢@@zudumalli
Bro can we connect cooling fan and power supply directly to bts7960 motor driver b- and b+
Yes
If we will not apply fan and let the box open so motor again burn????
When I play f1 the motor rich at 68 Celsius after 30 minutes.(with 2500rpm fan and ffb power 80%)
How much does this all cost
two.three over four inches in cm?
Can i use a power supply of 12v 5amp because I am using only steering and gas and brake along with ffb ( I don't need Padal shifter or h shifter )😊and can i use a laptop adapter of 12v without power supply
nope you need 15 amps because it will not work loss of power due to its short trravel
no, you can't. @BlUMILEEDITS is right. btw you can use 24v 5amp adapter.
@@zudumalli can we use 24v power supply with only one motor without any worries?
Can i replace the motor driver with DC controller
Because i have DC motor that have very high torque but it can't connect to motor driver but it can connect to DC controller
I don't have almost zero knowledge about boards can i use Arduino Leonardo R3 board
Yes
Which software are you using, and does it support steam games like f1.
If possible, can you explain how ardunio is connected to pc to detect it as a gamepad. Mostly software side of the build.
Thanks 😊
It does not require any software.
The wheelconfig software will automatically detect the game.
bro where did you buy arduino leonardo , for how much? (price)
I bought it from our local market (sri lanka ).
ok but how do you add buttons for shifting?
I dont need paddles but some might want them.
can it play on xbox series s forza or is it pc only ?
Analog pin of arduino board is used for shifters.
I will show about that later.
It is the PC Microsoft Store version that can be played.
Bro plz tell me the best arduino model for making ffb stearing while gear box and and clutch brake and acceleration best model
This firmware only supports to arduino Leonardo board only.
@@zudumalliarduino uno is no the best for making iy
did you code the Arduino?? . thank for the video but i was thinking that do we have to code the Arduino if yes could you please give the code
No, I'm installing the Firmware
how to mske the steering wheel only looks good
If you have the right tools, you can make the wheel look good
How much force feedback does these wheel have
1.3N.m like