Ah... skipped over the part I wanted to see. What was the clear stuff you spayed on? Are you using clear coat as a sealer? I am confused on how you get the new primer and paint to blend in with the pre existing stuff.. it seems like that would cause a problem.
Hi, mess sometihing from the vid, what happend with the doors? i see you was painted 2 door but i cant saw it when you prepered the doors, or you painted on the lack?
Good afternoon Edwin. That is just beautiful results. That primer you use really does a good job for you. Your use of different and various sand papers really makes a difference too. That shine is just perfect. Thanks for another great video have a good week and you take care.
Hi Steve!! Good afternoon, job came out very nice,that filler the uv filler is awsome,and can be used in very different situations. Have a great week my friend👍👍Thanks.
The most expected and satisfying part has not been recorded ! But ok, as you shown, both doors had to be painted totally. I was assuming that only the part you made the repair on would be painted.
Quite hard and tough big job. For me it would be easier to get someone to do it and just pay the bill. Because it would cost me more to buy tools, equipment, time and space. Good jod👍
hi there, i drive a honda accord cu2 in blackmetallic an have a similar damage size on my door in the lower part. what would be the cost for fixing that kind of damage if i give it away? thank you for replying sir🤝🏾
Just a tip from one to another, try to keep the Repair area as small as possible. When you sand down such a big area around the damage it gives a much longer, material consuming and also bigger area where you have a risk of geting something un-even. ”Better”.. or maybe at least more efficient, is to try and keep it as small as you are able to 😇 i work with only very small damages that can be ”spot repaired” so i basically never put clearcoat on an entire panel, only usualy the damaged area + 5-7 inches or 10-20cm around. Im not saying you need to repair like that since its hard and requires some experience with the clear. But the Repair up until clearcoat should be as small as possible, and then go ahead and just o it as normal and put clear over the whole panels if you dont know how to blend! 👍🏼 great video! Thx man
Can you go through the process please of filling a small penny size dent , that’s what I’m concerned about extending the situation beyond the dent to much and will the clear coat mask any transition from original paint to new paint and should I sand the new coat to flat prior to clear coat , your help would be appreciated, I’ve worked on large areas before but like in numbers where you can go to the joints and mask off , the dent I have to do is on wheel arch it’s rite on a body line line crease can’t use pdr no way in double skin , I have thought of drilling hole in rear skin to gain access to work it out but not so sure .
so true. its a such a small spot to be repainting that much panels. first off i wouldn't use those pneumatic sanders for that job. he damaged more clear coats in the surrounding area than he should have. when what he should have done its just base and top coat the spot only polish the surrounding area then use a blending reducer to blend the new clear coat to the old one. polish the whole panels when done.
Hey! I’m currently doing a repair like this but when I apply my primer I can still see the patch of the bondo, after watching this I know I need to go to finer sand paper gradually but just wondering if you sprayed anything over the bondo or was that just primer? Please give me any advice too to help me blend the bondo better so I’m not left with a patch/stain after painting Thanks!
@@preownedsales4495 it side not have to be feather edged with 80. You can do it with finer grit. You are right tho, has to be feather edged or it will show thru.
I get that you want to cut fast with the 80 but don’t want 80 grit on the paint. Would it be that much slower to just use the 220. Thanks for showing the grits most of the times.
Good comment @linus452345, i'm nowhere on you guys level doing that, but i was going to ask, why did he make a small area, that large, i thought you were to try to keep the area small, that gentle just made more work.
Cheers for this, I have been researching "osteoarthritis age 30" for a while now, and I think this has helped. Have you heard people talk about - Hanadelyn Banadison System - (search on google )? It is a great one of a kind guide for discovering how to get rid of arthritis without the hard work. Ive heard some unbelievable things about it and my co-worker got cool results with it.
So both doors got painted i see that but do the doors have to get sanded and primed or do you just color coat over the original clear coat? What kind of preparation needs to happen to the panels that weren't sanded and primed?
@@Vv_Twisted_vV Black doesn't need to blend as long as you have a black that matches. On the other hand, you'll see the different colors if you don't blend on sliver, white, yellow, etc With that being said, he did blend the paint, can you see the tape of the middle has black paint but left&right side don't?
Hallo apa masi ada lowongan pekerjaan sebagai mecanic dempul dan cat.??? Saya butuh pekerjaan sekarang Saya sudah berpengalaman Mohon infokan kalau masi ada ya Terimakasih Thank you so much
lol, mix your putty on a piece of cardboard or the onion paper books they make for that. He was wasting material dropping it on the floor. Throwing money away....
That car looks like it has been painted before. It look like it has a whole lot of orange peel . Or bad body work. not on your part but to the right on the video.
I guess the car just painted itself huh
Magic 🪄 😜
exceptional skills, this so call quick job is better than many other regular jobs.
Nice job how do you clean your scrapers they look spotless
Hi,what is the name of the filler putty you are using please. Great videos.
Awesome job man! What’s the liquid you’re using at 23:34 ? Is it IPA or just DI water to check for any highs/lows points?
Excellent work man!
Thanks
Ik vind het altijd maar weer knap, dat dit er weer strak uitziet!👍
Thanks man👍
Ha Ha love this Vid ! no crappy yappy ! just snap zap DONE ! thumbs up !
Ah... skipped over the part I wanted to see. What was the clear stuff you spayed on? Are you using clear coat as a sealer? I am confused on how you get the new primer and paint to blend in with the pre existing stuff.. it seems like that would cause a problem.
Hi, mess sometihing from the vid, what happend with the doors? i see you was painted 2 door but i cant saw it when you prepered the doors, or you painted on the lack?
Sei un grande bel lavoro
Can you tell me more about the 3m dust remover you are using? If it is dust remover ,i can't se the sine on it in the video .
Thanks in advance:)
Good afternoon Edwin. That is just beautiful results. That primer you use really does a good job for you. Your use of different and various sand papers really makes a difference too. That shine is just perfect. Thanks for another great video have a good week and you take care.
Hi Steve!! Good afternoon, job came out very nice,that filler the uv filler is awsome,and can be used in very different situations. Have a great week my friend👍👍Thanks.
? What kind of primer r u using
DOMINITYful , We use U-pol primers and fillers and sometimes Southern urethane primers and fillers. Thank you
بلکه واش پرایمر کار درست است
Nice job !
Great job 👌👌👌
How about a list of what tools you used?
The most expected and satisfying part has not been recorded !
But ok, as you shown, both doors had to be painted totally.
I was assuming that only the part you made the repair on would be painted.
Quite hard and tough big job. For me it would be easier to get someone to do it and just pay the bill. Because it would cost me more to buy tools, equipment, time and space. Good jod👍
Have a nice week,thanks for the vids!
O remendo Ere uma coisinha de nada e VC o estendeu e passou muinta .massa não precisava tanto assim
I wish you would have showed how you blend the paint
Good work man.
Proper job. Very nice. Wish you would have shown the paint work at the end though.
hi there,
i drive a honda accord cu2 in blackmetallic an have a similar damage size on my door in the lower part.
what would be the cost for fixing that kind of damage if i give it away?
thank you for replying sir🤝🏾
Just a tip from one to another, try to keep the Repair area as small as possible. When you sand down such a big area around the damage it gives a much longer, material consuming and also bigger area where you have a risk of geting something un-even.
”Better”.. or maybe at least more efficient, is to try and keep it as small as you are able to 😇 i work with only very small damages that can be ”spot repaired” so i basically never put clearcoat on an entire panel, only usualy the damaged area + 5-7 inches or 10-20cm around. Im not saying you need to repair like that since its hard and requires some experience with the clear. But the Repair up until clearcoat should be as small as possible, and then go ahead and just o it as normal and put clear over the whole panels if you dont know how to blend! 👍🏼
great video! Thx man
Can you go through the process please of filling a small penny size dent , that’s what I’m concerned about extending the situation beyond the dent to much and will the clear coat mask any transition from original paint to new paint and should I sand the new coat to flat prior to clear coat , your help would be appreciated, I’ve worked on large areas before but like in numbers where you can go to the joints and mask off , the dent I have to do is on wheel arch it’s rite on a body line line crease can’t use pdr no way in double skin , I have thought of drilling hole in rear skin to gain access to work it out but not so sure .
so true. its a such a small spot to be repainting that much panels. first off i wouldn't use those pneumatic sanders for that job. he damaged more clear coats in the surrounding area than he should have. when what he should have done its just base and top coat the spot only polish the surrounding area then use a blending reducer to blend the new clear coat to the old one. polish the whole panels when done.
I need instructions on how to repair a very small dent, and I am willing to pay
Some colours are hard though, some blends are terrible if not off a body line
Very clean detail...
Fantastisch vakwerk zeer interessant om te zien.
What type of rubber body filler spreader is that? I can't seem to find one anywhere.
24:17 Is there foam soft tape between doors?
Great job!!... "California"
please post what items u r using
Excellent grade 👍👌
Hey! I’m currently doing a repair like this but when I apply my primer I can still see the patch of the bondo, after watching this I know I need to go to finer sand paper gradually but just wondering if you sprayed anything over the bondo or was that just primer?
Please give me any advice too to help me blend the bondo better so I’m not left with a patch/stain after painting
Thanks!
Ben learning bodybwork for a year now i learned u have to feather the area around the bondo with 80 grid but before this sand bondo to a smooth finish
@@preownedsales4495 it side not have to be feather edged with 80. You can do it with finer grit. You are right tho, has to be feather edged or it will show thru.
In my workshop, 2 of us used to work on 10 vehicles daily
Do you have a link to that dual action sander?
Beautiful work!
thats a Mirka Deros
@@TU154B1
Thank you
Just a waste of time !!!! Did not show how did he paint it. Thats why you dont have many viewers. Your video is juat a waste of dat load
Whats that he used at 8:20? Also which grit right after that treatment?
the UV primer is good doesnt shrink
U r goooooood sir wow!!
Thanks!!!
that panel re-sprayed before ?
because that orange peel is so bad
I get that you want to cut fast with the 80 but don’t want 80 grit on the paint. Would it be that much slower to just use the 220. Thanks for showing the grits most of the times.
I think body filler won't bond to sanding scratches higher than 80.
Nice job, what primer did you use?
Thanks, i use a uv filler
Nice job
whether it is UV lama for drying all primers and colors or only for UV primer and color? Nice work
Uv lamp is only for drying the uv filler.there is no uv drying color by my knows
When you forget to put the sandpaper back on the DA
Good job
Nice job my friend 😁👍👍👍 👍👍👍✌
Muhammed My friend!!!!! Thanks bro👍👍👍
Vrhunski,prefectee
Missing the last part where you paint the area
Could you tell me what electric Da sander you are using.
i think is Mirka Deros...
www.nonpaints.com/nl/mirka-deros-schuurmachine-150mm-met-trillingssensor-bluetooth
Did you put color on the whole panel or just the repair area and then cleared the whole panel
He sprayed the whole door with base then clearcoat.
Awesome
Which primer using
Why not just use pdr? Why all this mess?
What liquid do you have in the botle and at the end of the video clean all surface?
Alcohol, buddy..!
Damn... Wished you'd included the painting... Oh well, maybe next time! :-)
How did he paint it ?
What is the substance you used in the 8:17 minute
Does the whole panel then have to be sprayed or blended?
My understanding is the base coat is blended to rest of panel but the entire panel gets clearcoat.. I believe.
Perfection
Good comment @linus452345, i'm nowhere on you guys level doing that, but i was going to ask, why did he make a small area, that large, i thought you were to try to keep the area small, that gentle just made more work.
Joia!!!
car is like ahhh been trying to get that itch for years 😩
Is it 2k primer
Guy is fuckin sanding areas that are still good...lol
Good job 💯👍👏🥰😍
Thanks👍🏻👍🏻😁😁
So annoying watching somebody you scrapers as a spreaders find it so difficult to watch . But he is good at he’s job .
Immy Zaman fr
N 1 👍👍👍🌹🌹🌹👍👍👍
check out our hand held UV LED Lamp ! Best one on the world market bro!
Amazing result!
Fine
it would be lots better if the guy said what grade of paper hes using here instead? of trying to hold up to the cam,,, as cannot always see it,,,,,,
Can anyone tell me where I can get does two big spreader? And are they made from aluminium ?
Highly appreciated!
They just regular home decorating scrapers by the looks of it.
Nice work
do a post edit narration like Gunny is doing and your videos will be 1 grade better!
I should have missed the quick part
-Quick Job!
**paints entire two doors**
very good work and nice result..!!!!!
Thanks friend!!!
If you don't use body filler, tell us about it too
I want you to teach me
“Few word do trick”
Did you spray eproxy primer? is that what that was
Uv-filler
16:16 wat voor potje is dat en wat doet het?
👌
but how did he paint it?? thats why im here...
Cheers for this, I have been researching "osteoarthritis age 30" for a while now, and I think this has helped. Have you heard people talk about - Hanadelyn Banadison System - (search on google )?
It is a great one of a kind guide for discovering how to get rid of arthritis without the hard work. Ive heard some unbelievable things about it and my co-worker got cool results with it.
Was a basic paint job on two doors. The rest was masked off. So, no he did not blend the paint.
So both doors got painted i see that but do the doors have to get sanded and primed or do you just color coat over the original clear coat? What kind of preparation needs to happen to the panels that weren't sanded and primed?
@@Vv_Twisted_vV Black doesn't need to blend as long as you have a black that matches. On the other hand, you'll see the different colors if you don't blend on sliver, white, yellow, etc
With that being said, he did blend the paint, can you see the tape of the middle has black paint but left&right side don't?
Hallo apa masi ada lowongan pekerjaan sebagai mecanic dempul dan cat.???
Saya butuh pekerjaan sekarang
Saya sudah berpengalaman
Mohon infokan kalau masi ada ya
Terimakasih
Thank you so much
Your good but it doesn’t help anyone when you don’t tell them what your doing exactly
They spoil things a lot ... masking rolls
No dust extraction..
lol, mix your putty on a piece of cardboard or the onion paper books they make for that. He was wasting material dropping it on the floor. Throwing money away....
When you try to be smooth but keep dropping the product, lol
Sorry but the green putty is very thin and runs of the knife very quick. I do my best😉
Dude thanks for showing the paint application!!!??? Wth
💥
Alles gut
Zeker,met jou?
I love you help me
That car looks like it has been painted before. It look like it has a whole lot of orange peel . Or bad body work. not on your part but to the right on the video.
Didn’t even show the painting process
Why use a block then go right back to your da?
top result!!!
Man open that fuckin door!!!
Ty ale te szpachelki to ścian w domu do gipsu
That mask does nothing with that Huge Beard you have lmao. Osha would tell you to shave it all off