I have had one for a number of years now and it has never missed a beat for me. I am totally sold on this unit. I weigh my loads on a scale after the Gen6 dispenses them and found it to be very accurate. One thing though, after you empty the powder out of the powder dispenser, make sure you return the drain switch to the closed position. It makes quite a mess if you done. Don’t ask me how I know. Overall, it is a really great dispensor!
I have had my Gen 6 for nearly a year now. I love the size and form of it. Due to limited space I store mine in its box and inside the anti static bag it comes in. The in built speaker is annoying at times and a volume control would be good addition. I also like the fact they give you a spare set of bearings also. This was an upgrade from me from my Hornady lock n load bench scale
For the last six months I’ve really been enjoying your videos! I know you’ve been using “Varget” For reloading frequently, A friend of mine for more than 40 years named Tim has been a NRA master reloader for 20+ years, in the last week we had a conversation about “Varget”. Tim said he doesn’t care for Varget because it has nitro in it and nitro is very corrosive to barrels. Our conversation ended there about Varget since I didn’t know enough to comment. I sure appreciate your comments about Varget, nitro and the fact on barrels. Thank you!
I would have liked you to present the table as you have with other powder measures/dispensers of ten throws with two types of powders. The table helps us compare the accuracy between powder measures to help us make purchasing decisions.
I have just used my Gen 6 to load ammo for the first time it is a great little machine, also upgraded to a Lyman all American 8 press and the new hand primer and a new .308 die set I am most impressed with the latest dies from Lyman also have new 6mm Rem and 38/357 die sets they are some of the best die sets I have used, I am a big fan of the old PA dies been using them since the 1970's
Have you ever used a ZeroStat anti-static gun? Great non-contact, directional, static neutralizer. No batteries, no polonium, and works pretty well. I've had the same ZeroStat 3 for years and used it thousands of times. Great little piece of kit for getting rid of static.
after powder throw in the lyman, you should have then measured it in a .01 grain scale to see what kind of deviation it had at that level from charge to charge.
I`ve used several different electronic scales the last few years, and i always end up going back to my Redding drop powder measure`s every time and getting rid of the electronic ones. Because of how accurate the Redding is, and i don`t waste all this time waiting for an electronic powder measure to measure each of my loads. Gadgetry, everybody wants the latest flavor. I`m over it.
I took a chance on the gen 6 and I have had it for 2 years now and cant reload without it. The only powder I have not metered is flake (dont use it). It meters very well and is very consistent. I used to use a secondary scale to verify charge weights but due the accuracy it simply isnt needed. After it calibrates I just run 3 - 4 “ test” loads thru it to prime it up and its dead on after that. I might get 1 in every 10 loads off by a 10th of grain. If that happens I just dump the powder back in the hopper (that will hold up to a 1lb of powder) and throw another charge. Its very user friendly and simple to operate. If you use the auto charge function it will throw charges faster than you can keep up. The numbers on the display are big and easy to read. Clean up is a snap and powder dump door is the BOMB!
@@trialsdungeons8737 Yes you can use it for pistols. I reload for several pistol calibers as well. Its not any more difficult or any more work than reloading for rifles. You just calibrate your scale as you normally would before any reloading session, add your pistol powder to the hopper and your off and running. Hope this helps.
@@trialsdungeons8737 I have easily loaded several thousand rifle and pistol rounds and have used it for 2-3 hours at a time and it has always worked perfectly. I know some reloaders who use this machine and they have told me once they turn it on they have just left it on to save time and not have to re-calibrate every time they use it. They are much heavier reloaders than I am and they havent had any issues either. I am not sure if that helps answer your question but thats been my experience. I can also tell that Lymans customer service has been been top notch for any questions I have ever had about their products. If you have additional questions they might be a good resource to utilize for more in-depth info.
@@JH-lc8xd thank you for answering me, im new to reloading and im from brazil, its much more expensive to reload down here, and to acquire this machine, might cost me 3x as much in comparison to the US price tag, thats why im doing a good research
The Auto Count feature is great to cross reference the number of thrown loads vs the number in your block. I caught myself missing a case when I realized I only threw 49 rounds into 50 brass.
I've been meaning to review this on my channel but decided not to because I thought, "Who gives a darn about the Gen 6 now, it's been out for years!" Ha ha, apparently I was wrong. Good video!
I like mine. But with ball powders it would throw it all over. Found a 3D printed pan that was taller on an auction site. Also ball powders would work their way into the o ring seals. The aluminum tube will seize. Did some research online. Take a q-tip and wipe inside of o ring with some Mobile one synthetic high mileage oil. Works perfectly now.
Great review guys! I was deciding between an electronic and old school drop measure. I went with a Redding 3BR with both meters, about the same price range ($250ish). I think for loading blocks where you can run the block under the measure the old school is faster. Depending on the powder the Redding is very accurate. Plus you don't have to mentally keep track of which was the last case you filled, you're just moving down the line. (pistol cases) Tall rifle cases may not be able to do that. If I could have both I would definitely buy the Gen6.
I've had a gen6 for about 3 years now. It been great for extruded powders. Seems to throw a tenth high but fairly easy to compensate for. I still use Lee Precision gravity drop for ball powders
I love my gen 6. Usually throws a tenth high on extruded powders. But other than that it's a great add to my setup. I would recommend it for any reloader.
I wish you would have done the accuracy check with the Varget. I’ve found the powder weight with both Varget and AR-Comp is 0.1 grains heavy >90% of the time. I also have issues with the touch screen not being responsive and if the charge was light I would trickle and the scale was not showing a change in weight until it was too much. I do like the small form factor since I only have a small bench setup. Thanks for the great video.
@@ryanoros9562 A wise guy told me if you want to raise great kids stay crazy! He said now I am the only 50 year old man in the neighborhood who's kids go around screaming DAD TURN THE MUSIC DOWN! Kids always rebel against authority, great parents run with the trend!
Gavin an interesting test would be to compare loads weighed out on the multiple auto dispensers to the lab scale loads. Load say 10 rounds of a known load that has low SD, ES and tight group on each scale/dispenser. Fire 1 five shot group at 100 - 500 yards and compare the numbers.
Hi Gavin, Could you do more repeatability and accuracy testing with a bigger than 1 sample size, Maybe like a tested story or just a bigger sample set discharging 50 charges and putting them on the balance to get a precise measurement to compare?
He isn't going to do any more than a show how it works. He doesn't really endorse anything. He pretty much shows you how things work. He uses better systems than most the stuff he demonstrates. He's making money doing this. He will show you how something works and leaves it to the consumer what to choose for themselves.
It operates very similar to my Hornady powder dispenser!!! It seems easier to get started with when unfamiliar with the unit. How many over throws did you experience? From your test it seemed pretty solid!!!
I have a gen5. In the beginning, i was pleased with it. After some months it was getting increasingly harder to give the 1/10 of grains correct. And then it started drifting. After complaing i was told to clean the gen 5 due to static problems. No change. I then bought a rcbs instead. Much more consistent. I then tested both side by side. I could not trust the gen5, still inkonsistent, so now i only use the rcbs. The gen5 is collecting dust.
What people forgett is the season changes! Here, in northen sweden, we generaly have below zero C from nov to march-april. That makes the air dry, causing alot more static charge. Its impossible to get rid off, as 0% humidity makes it sensitve. Even the plastic plattern on my Intellidropper affects it, and the cover is unusable and the plastic spoons that come with lee kits affect it to. But during summer it works perfectly. Same goes for digital scales, they are to sensitive. The new gen 3 hornady scale work better as the plattern is metalic, unlike the gen 2.
A volume control on the beep would be nice, but I neutered mine in about 5 minutes. Remove the bottom cover and the screws for the keypad. Under the lower left of the keypad is the speaker, it's a hollow cylinder about the diameter of a dime. Take some hot glue and shoot it in there. You will end up with a very quiet squeak, rather than a loud beep.
I bought my Lyman just over two years ago for $250. It worked fairly well until it didn’t. One day with no warning it just quit working & wouldn’t zero the scale anymore rendering it useless. It gave readings all over the map. Scale drift was (4) full grains in a minuet. I contacted Lyman support; they gave me some things to try. It was no use. She never worked again. Bottom line… I got maybe 1000 rifle cases charged in the two years of use for $250. Save your money, buy something better. You don’t have to spend $1000 on a scale. But there are numerous other options out there. I went with the Hornady Auto Charge Pro for $340. We’ll see how that works.
I had the Gen 2. Thought I really had something until I got into long range shooting and started checking drops with a beam scale. I bought a V3 autotrickler and never looked back. Don't get me wrong, for short range pistol/plinking the lyman is fine but if you're looking for consistency you're going to either have to stick with hand trickle/beam scale or open the wallet and spend a bit more for the RCBS or autotrickler.
if your load lives on the 0.02 grain difference, you are loading way to sensitive ammution! A stable load works with up to 0.5 grains difference. Load weight is just one small part, and for extreme accuracy i can even argue its not the most importaint. Necktension, barrel temperature etc give you way more flyers. If you need 0.1 accuracy to shoot 0.5 moa or less, you need to re-evaluate your load development. Or how do you handle temperature? Hot barrels, cold barrels etc.
I have a Gen6, after my first round of reloading. I took it apart and "disabled" the speaker. Would have been nice if there was a volume adjustment or mute.
Love the videos would love to see a brand comparison video for electronic dispensers similar to the ones you did for the presses for reference your progressive press video is what ultimately made up my mind on the press I use regularly
Would have liked to see you double check the powder throw with a beam scale. I could say a lee dipper gives great results unless verified by using a beam scsle..
I loved my gen 6- until it started dispensing low charges (like 5 or 6 grain short). It would pour out the first bit at regular speed, then go into slow trickle mode, make a whining sound, trickle really slow and eventually stop way short. Any suggestions?
very good looking but now in Spain I don't know why there is no material for recharging, they have been limiting it for a long time and it is even suspicious,
Wouldn't it be good if it weighed the case, maybe zeroing it out, then dumped a set amount into the case instead of a pan. That way you knew for sure the amount in the case and saves a step. Eliminates some grains not making from pan into case.
This got me excited! Thought it would be a great affordable upgrade for my RCBS 2000 digital scale. Soooooo right after watching the video I went to Amazon website and looked it up. $588.00 before taxes and shipping Canadian. Oh well ☹.
I have a Gen 6 that I haven't had the chance to use yet, but calibration of my Lyman XP-1500 electronic scale seems to wander when the barometric pressure is rising and falling rapidly, and when it's really stormy, forget it. Have you noticed wandering calibration with the Gen 6?
Easy to use clean out is actually easy takes about 3 min my only gripe is the beep is there a way to shut it off? I reload in my bedroom and you can hear it all over the house.Varget also works well in 45-70 and found a few loads using W748 1800 FPS out of 27” barrel, I like powders that are useable in multiple calibers because of spotty availability of powders( it has gotten better lately)
I'm on a mission to preach the neutered beeper, because I think it's the only thing really wrong with the G6. The beeper is in the machine under the keypad. Inject some hot glue in the beeper and you will kill 90% of the volume.
"It starts out right with warnings" I mean the only warning I'd be OK with is if it said "we advise not ashing your cigarette into the pan while it's dispensing the powder."
Show the calibration of the two scales when doing a head to head accuracy test. Also use the same calibration weight for both scales. Please stop dumping the pan so quickly. Let it settle out.
!Shock! This scale doesn't like percussive maintenance? I'm intrigued and even though I'm a progressive guy, I can see where this would come in very handy.
I won't buy a Lyman product that could need warranty replacement, because their after-sale support is so widely criticized. Look up something like a scale & read the most critical reviews at retail sites, and you'll see what I mean. When Lyman products are good, they're good, but if you got a lemon that made it through their QC process, you're screwed.
Investing in *Cryptocurrency* now should be in every wise individuals list, in some months time you'll be ecstatic with the decision you made today.........BE WISE..
@@stateangel2300 Yeah, My first investment with Mr Christian Thomas Clinton earned me profit of over $25,530 US dollars, and ever since then he has been delivering it.
I can tell you right out of the gate you will never be able to clean this unit...EVER. It’s easy to use and seems accurate but any and every smokeless powder will melt to inside workings. I had 2 of them and don’t use them anymore.
I understand you are trying to show the newest and hopefully best products on the market for reloaders but is this just too much technology for a simple task. I have had a Redding powder measure, Ohaus 1010 scale, and RCBS powder trickler since 1970 and they work fine. At a cost of $300 dollars plus I can better spend that money on components.
Touch screen? But it's not a touch screen is it? No it's ta capacitive keyboard which is the abomination of keyboards. It lacks the tactile feedback and click confirmation of physical keyboard yet it's locked in place and offers no additional configurability of touchscreen.
And may I add that the keyboard and the selected backlight color reminds me of the cheapest OEM Chinese electronics there is. Blue hue background is the de-facto worst choise to make.
Love how you approach these things. My only complaint is watching your channel is proving to be expensive!
I have used the Gen6 for a couple of years now. Totally happy with it.
I have had one for a number of years now and it has never missed a beat for me. I am totally sold on this unit. I weigh my loads on a scale after the Gen6 dispenses them and found it to be very accurate. One thing though, after you empty the powder out of the powder dispenser, make sure you return the drain switch to the closed position. It makes quite a mess if you done. Don’t ask me how I know. Overall, it is a really great dispensor!
I have had my Gen 6 for nearly a year now. I love the size and form of it. Due to limited space I store mine in its box and inside the anti static bag it comes in. The in built speaker is annoying at times and a volume control would be good addition. I also like the fact they give you a spare set of bearings also. This was an upgrade from me from my Hornady lock n load bench scale
Nick, see my top line comment. You can neuter the beep with some hot glue in about 5 minutes.
@@joelcurtin9409 thanks
For the last six months I’ve really been enjoying your videos!
I know you’ve been using “Varget” For reloading frequently, A friend of mine for more than 40 years named Tim has been a NRA master reloader for 20+ years, in the last week we had a conversation about “Varget”. Tim said he doesn’t care for Varget because it has nitro in it and nitro is very corrosive to barrels. Our conversation ended there about Varget since I didn’t know enough to comment.
I sure appreciate your comments about Varget, nitro and the fact on barrels.
Thank you!
Greetings from NY: Gavin you never have enough room when start reloading. RELOADING IS ADDICTING!
Been using this for just over a year, no complaints
I would have liked you to present the table as you have with other powder measures/dispensers of ten throws with two types of powders. The table helps us compare the accuracy between powder measures to help us make purchasing decisions.
I had decided on the Gen 6, by reviews. Now that I see it actually works, I am sold!
I have just used my Gen 6 to load ammo for the first time it is a great little machine, also upgraded to a Lyman all American 8 press and the new hand primer and a new .308 die set
I am most impressed with the latest dies from Lyman also have new 6mm Rem and 38/357 die sets they are some of the best die sets I have used, I am a big fan of the old PA dies
been using them since the 1970's
Mine is arriving tomorrow, can't wait to give it a go!
That auto is a nice feature. Saves wear and tear on the touch screen and enter button.
Have you ever used a ZeroStat anti-static gun? Great non-contact, directional, static neutralizer. No batteries, no polonium, and works pretty well. I've had the same ZeroStat 3 for years and used it thousands of times. Great little piece of kit for getting rid of static.
Wow that intro is loud.
after powder throw in the lyman, you should have then measured it in a .01 grain scale to see what kind of deviation it had at that level from charge to charge.
I have one it gets the job done not the best but very easy to use
Wow, how reloading has changed since I started in the mid 1970's..........and a LOT more expensive too!
I`ve used several different electronic scales the last few years, and i always end up going back to my Redding drop powder measure`s every time and getting rid of the electronic ones. Because of how accurate the Redding is, and i don`t waste all this time waiting for an electronic powder measure to measure each of my loads. Gadgetry, everybody wants the latest flavor. I`m over it.
a smack against static is a dryer sheet to wipe down everything
I took a chance on the gen 6 and I have had it for 2 years now and cant reload without it. The only powder I have not metered is flake (dont use it). It meters very well and is very consistent. I used to use a secondary scale to verify charge weights but due the accuracy it simply isnt needed. After it calibrates I just run 3 - 4 “ test” loads thru it to prime it up and its dead on after that. I might get 1 in every 10 loads off by a 10th of grain. If that happens I just dump the powder back in the hopper (that will hold up to a 1lb of powder) and throw another charge. Its very user friendly and simple to operate. If you use the auto charge function it will throw charges faster than you can keep up. The numbers on the display are big and easy to read. Clean up is a snap and powder dump door is the BOMB!
hi do you still have it ? can i use it for pistols too, or is that too much work ?
@@trialsdungeons8737 Yes you can use it for pistols. I reload for several pistol calibers as well. Its not any more difficult or any more work than reloading for rifles. You just calibrate your scale as you normally would before any reloading session, add your pistol powder to the hopper and your off and running. Hope this helps.
@@JH-lc8xd thank you that helps a lot, for how many hours straight do you use the gen 6 ? have it ever break down ?
@@trialsdungeons8737 I have easily loaded several thousand rifle and pistol rounds and have used it for 2-3 hours at a time and it has always worked perfectly. I know some reloaders who use this machine and they have told me once they turn it on they have just left it on to save time and not have to re-calibrate every time they use it. They are much heavier reloaders than I am and they havent had any issues either. I am not sure if that helps answer your question but thats been my experience. I can also tell that Lymans customer service has been been top notch for any questions I have ever had about their products. If you have additional questions they might be a good resource to utilize for more in-depth info.
@@JH-lc8xd thank you for answering me, im new to reloading and im from brazil, its much more expensive to reload down here, and to acquire this machine, might cost me 3x as much in comparison to the US price tag, thats why im doing a good research
The Auto Count feature is great to cross reference the number of thrown loads vs the number in your block. I caught myself missing a case when I realized I only threw 49 rounds into 50 brass.
ha interesting
You guys are great together! Keep up the good work
I have 2 of them and I use it with my AND scale which I had seen on ultimate reloaded.
I've been meaning to review this on my channel but decided not to because I thought, "Who gives a darn about the Gen 6 now, it's been out for years!" Ha ha, apparently I was wrong. Good video!
I like mine. But with ball powders it would throw it all over. Found a 3D printed pan that was taller on an auction site. Also ball powders would work their way into the o ring seals. The aluminum tube will seize. Did some research online. Take a q-tip and wipe inside of o ring with some Mobile one synthetic high mileage oil. Works perfectly now.
I love the gen 6 I run 2 side by side for prs reloading.
When I lived in an apartment the one piece that made reloading way easier was the Lee Handpress. Amazing tool that let me reload 8mm, 243, 223.
Great review guys! I was deciding between an electronic and old school drop measure. I went with a Redding 3BR with both meters, about the same price range ($250ish). I think for loading blocks where you can run the block under the measure the old school is faster. Depending on the powder the Redding is very accurate. Plus you don't have to mentally keep track of which was the last case you filled, you're just moving down the line. (pistol cases) Tall rifle cases may not be able to do that. If I could have both I would definitely buy the Gen6.
I love mine, super easy to use and accurate!!!
I've had a gen6 for about 3 years now. It been great for extruded powders. Seems to throw a tenth high but fairly easy to compensate for. I still use Lee Precision gravity drop for ball powders
hi, is thr gen 6 still working ? guess ill buy one, do you use it for pistols or just rifle?
Bought one myself works great ty for the review
Glad I could help!
I love my gen 6. Usually throws a tenth high on extruded powders. But other than that it's a great add to my setup. I would recommend it for any reloader.
I wish you would have done the accuracy check with the Varget. I’ve found the powder weight with both Varget and AR-Comp is 0.1 grains heavy >90% of the time. I also have issues with the touch screen not being responsive and if the charge was light I would trickle and the scale was not showing a change in weight until it was too much. I do like the small form factor since I only have a small bench setup. Thanks for the great video.
love this video i have this one on my bench
I liked it so well I bought the whole kit.
Can't wait to get mine out of the box maybe tomorrow !!! Thanks Guys 👍🏻
Like the new lead in music!
I thought it was way to loud & everybody in the house yelled at me to turn it down
@@ryanoros9562 A wise guy told me if you want to raise great kids stay crazy! He said now I am the only 50 year old man in the neighborhood who's kids go around screaming DAD TURN THE MUSIC DOWN! Kids always rebel against authority, great parents run with the trend!
Now I will be waiting for an ALL Manufacturer comparison
As a check. Can you put the test weight in the scale . Every so many drops , as a check? And then go right back to dispensing?
Got one and I love it
Gavin an interesting test would be to compare loads weighed out on the multiple auto dispensers to the lab scale loads.
Load say 10 rounds of a known load that has low SD, ES and tight group on each scale/dispenser. Fire 1 five shot group at 100 - 500 yards and compare the numbers.
Hi Gavin, Could you do more repeatability and accuracy testing with a bigger than 1 sample size, Maybe like a tested story or just a bigger sample set discharging 50 charges and putting them on the balance to get a precise measurement to compare?
He isn't going to do any more than a show how it works. He doesn't really endorse anything. He pretty much shows you how things work. He uses better systems than most the stuff he demonstrates. He's making money doing this. He will show you how something works and leaves it to the consumer what to choose for themselves.
It operates very similar to my Hornady powder dispenser!!! It seems easier to get started with when unfamiliar with the unit. How many over throws did you experience? From your test it seemed pretty solid!!!
99% of the time it throws under, not over
@@luckyshotammunitiongunsllc2369 that is a big plus.
can this be used for nutrition powder for measuring nutrients for brewing wine?
I have a gen5. In the beginning, i was pleased with it. After some months it was getting increasingly harder to give the 1/10 of grains correct. And then it started drifting. After complaing i was told to clean the gen 5 due to static problems.
No change. I then bought a rcbs instead. Much more consistent. I then tested both side by side. I could not trust the gen5, still inkonsistent, so now i only use the rcbs. The gen5 is collecting dust.
What people forgett is the season changes! Here, in northen sweden, we generaly have below zero C from nov to march-april. That makes the air dry, causing alot more static charge.
Its impossible to get rid off, as 0% humidity makes it sensitve. Even the plastic plattern on my Intellidropper affects it, and the cover is unusable and the plastic spoons that come with lee kits affect it to.
But during summer it works perfectly.
Same goes for digital scales, they are to sensitive. The new gen 3 hornady scale work better as the plattern is metalic, unlike the gen 2.
I’ve had a Gen 5 for 7 years and it still works fine.
A volume control on the beep would be nice, but I neutered mine in about 5 minutes. Remove the bottom cover and the screws for the keypad. Under the lower left of the keypad is the speaker, it's a hollow cylinder about the diameter of a dime. Take some hot glue and shoot it in there. You will end up with a very quiet squeak, rather than a loud beep.
I have a FA Intellidropper. I love it! The best buy I did.
Hello, I use the same , and I,m very happy but I check envery load with my old Pacific scale. My press is Lyman orange crusher.
the scale seems to drift alot. powder likes to bounce out of the pan. an anti static mat improves the drift. easy to clean.
What is the "new improved technology" advertised on the box?
Kind regards
I bought my Lyman just over two years ago for $250. It worked fairly well until it didn’t.
One day with no warning it just quit working & wouldn’t zero the scale anymore rendering it useless. It gave readings all over the map. Scale drift was (4) full grains in a minuet.
I contacted Lyman support; they gave me some things to try. It was no use. She never worked again.
Bottom line… I got maybe 1000 rifle cases charged in the two years of use for $250.
Save your money, buy something better. You don’t have to spend $1000 on a scale. But there are numerous other options out there. I went with the Hornady Auto Charge Pro for $340. We’ll see how that works.
I had the Gen 2. Thought I really had something until I got into long range shooting and started checking drops with a beam scale. I bought a V3 autotrickler and never looked back. Don't get me wrong, for short range pistol/plinking the lyman is fine but if you're looking for consistency you're going to either have to stick with hand trickle/beam scale or open the wallet and spend a bit more for the RCBS or autotrickler.
if your load lives on the 0.02 grain difference, you are loading way to sensitive ammution! A stable load works with up to 0.5 grains difference.
Load weight is just one small part, and for extreme accuracy i can even argue its not the most importaint. Necktension, barrel temperature etc give you way more flyers.
If you need 0.1 accuracy to shoot 0.5 moa or less, you need to re-evaluate your load development. Or how do you handle temperature? Hot barrels, cold barrels etc.
Where does this fit in compared to your FX120i lab grade scale and autotrickler? Are they even close by comparison?
You put your hand in front of the screen when it shows the final weight so we never get to see that?
I think my wallet is lighter now... cause I bought the kit 💁♂️
I have a Gen6, after my first round of reloading. I took it apart and "disabled" the speaker. Would have been nice if there was a volume adjustment or mute.
Love the videos would love to see a brand comparison video for electronic dispensers similar to the ones you did for the presses for reference your progressive press video is what ultimately made up my mind on the press I use regularly
thanks for showing the auto trickler but I still cannot find a reason to use these.
Is it temp sensitive? I load in my garage and my RCBS will not calibrate it hot or cold temps. All measuring has to be done in the house.
Never got to see the final weight of the CFE, the hand always covered it. Did it ever go over?
Hello where can I retrieve the original transformer?
Would have liked to see you double check the powder throw with a beam scale.
I could say a lee dipper gives great results unless verified by using a beam scsle..
Pretty darn sweet is what it is!
Can you adjust the feet for level
Have a Gen 6 and enjoy it if just don't like any air flow like a draft have it for 2year already no problems with it
I loved my gen 6- until it started dispensing low charges (like 5 or 6 grain short). It would pour out the first bit at regular speed, then go into slow trickle mode, make a whining sound, trickle really slow and eventually stop way short. Any suggestions?
You should check it against a really accurate scale
hello could you recommend a value for money starter kit for a novice trying to get into reloading
very good looking but now in Spain I don't know why there is no material for recharging, they have been limiting it for a long time and it is even suspicious,
Wouldn't it be good if it weighed the case, maybe zeroing it out, then dumped a set amount into the case instead of a pan. That way you knew for sure the amount in the case and saves a step. Eliminates some grains not making from pan into case.
This got me excited! Thought it would be a great affordable upgrade for my RCBS 2000 digital scale. Soooooo right after watching the video I went to Amazon website and looked it up. $588.00 before taxes and shipping Canadian. Oh well ☹.
Ouch
Just saw that Brass Pro (Cabela's) has it on sale (April) in Canada $287.99 + Tax with free shipping over $149.00 now that is a deal! Good Hunting.
Great review
Di quale trasformatore ha bisogno ?
I have a Gen 6 that I haven't had the chance to use yet, but calibration of my Lyman XP-1500 electronic scale seems to wander when the barometric pressure is rising and falling rapidly, and when it's really stormy, forget it. Have you noticed wandering calibration with the Gen 6?
My Gen6 keeps wanting to re calibrate even after 10 or 30 loads very frustrating gone back to RCBS1010, slow but accurate
yOU HAVE TO KEEP it clean otherwise a beeping error goes off But still works
Very nifty piece of kit,
this dispenser doesn't have a level?
Easy to use clean out is actually easy takes about 3 min my only gripe is the beep is there a way to shut it off? I reload in my bedroom and you can hear it all over the house.Varget also works well in 45-70 and found a few loads using W748 1800 FPS out of 27” barrel, I like powders that are useable in multiple calibers because of spotty availability of powders( it has gotten better lately)
I'm on a mission to preach the neutered beeper, because I think it's the only thing really wrong with the G6. The beeper is in the machine under the keypad. Inject some hot glue in the beeper and you will kill 90% of the volume.
Read above, one guy took it appart and disabled it. That may be your only solution.
"It starts out right with warnings"
I mean the only warning I'd be OK with is if it said "we advise not ashing your cigarette into the pan while it's dispensing the powder."
For an overview of the machine and how it works don’t you think actually covering how to drain the powered and clean the machine is kind of important
Show the calibration of the two scales when doing a head to head accuracy test. Also use the same calibration weight for both scales. Please stop dumping the pan so quickly. Let it settle out.
I would love to see a full blown accuracy test done with the lab scale to see es and sd of the lyman compared to the hornady and rcbs
It’s a sales pitch not a review
I like that GEN six I might have to get me one good video men what is the price of that powder measure. ? 👍👍🤠🔫
!Shock! This scale doesn't like percussive maintenance? I'm intrigued and even though I'm a progressive guy, I can see where this would come in very handy.
Nice
Interesting
I won't buy a Lyman product that could need warranty replacement, because their after-sale support is so widely criticized. Look up something like a scale & read the most critical reviews at retail sites, and you'll see what I mean. When Lyman products are good, they're good, but if you got a lemon that made it through their QC process, you're screwed.
I've liked your channel for quite awhile...but the into music at the start of the videos is overly loud.
HOW MUCH,,,,,HOW MUCH ALREADY......
Great tool, useless though without primers
発売と同時位から使っています👍🎵🎶☀️💡
良い商品です👍🎵🎶☀️💡
Lower you music intro, so I dont have to skip 1 min forward on all your videos ;-)
Investing in *Cryptocurrency* now should be in every wise individuals list, in some months time you'll be ecstatic with the decision you made today.........BE WISE..
Most intelligent words I've ever heard.
crypto is the new gold.
I wanted to trade in Crypto but got discouraged by fluctuations in prices.
@@stateangel2300 That won't bother you if you trade with a professional like Mr Christian Thomas Clinton
@@PoliticsByTabith I heard that his strategies are really good?
@@stateangel2300 Yeah, My first investment with Mr Christian Thomas Clinton earned me profit of over $25,530 US dollars, and ever since then he has been delivering it.
I read the directions too. Only fools don't read directions.
I can tell you right out of the gate you will never be able to clean this unit...EVER. It’s easy to use and seems accurate but any and every smokeless powder will melt to inside workings. I had 2 of them and don’t use them anymore.
I understand you are trying to show the newest and hopefully best products on the market for reloaders but is this just too much technology for a simple task. I have had a Redding powder measure, Ohaus 1010 scale, and RCBS powder trickler since 1970 and they work fine. At a cost of $300 dollars plus I can better spend that money on components.
Touch screen? But it's not a touch screen is it? No it's ta capacitive keyboard which is the abomination of keyboards. It lacks the tactile feedback and click confirmation of physical keyboard yet it's locked in place and offers no additional configurability of touchscreen.
And may I add that the keyboard and the selected backlight color reminds me of the cheapest OEM Chinese electronics there is. Blue hue background is the de-facto worst choise to make.
The Modern Lyman Family.. Has Destroyed the real "lyman Name" period.. SOO Sad. Just ask Me/..I Know The Real Story...
Destructions,....lol