Complete 250cc 2 Stroke Rebuild | 79 Odyssey FL250 Build Part 1
ฝัง
- เผยแพร่เมื่อ 8 ก.ย. 2024
- In this video the FL250 build is finally starting. A center-point of this 2-stroke off road go kart is this engine, so we are super eager to work on it and finally get it running. We built this motor from the ground up, including new crank bearings and seals, new crank bearings, and a new piston with a bored out cylinder. This Ody is a 1979 FL250 and we are super excited to continue and finish the restoration!
Thanks for watching and be sure to subscribe for the rest of the build!
MUSIC - If you liked the music in this video be sure to check out my buddies Soundcloud! / 2618a
andrewapplepie...
++++GPS- www.gopowerspor...
STICKERS!!!
buildbreakrepe...
^^^^^^^^Get your stickers here ^^^^^^^
Bottom end rod bearing is a must in a complete rebuild. Keep it up, lookin good guys.
Great video guys. Great Job on the engine rebuild. A little tip when you are doing bearings like you did on this engine a trick I used to do when I was racing boats is put the bearing in the freezer like you did but instead of using a torch on the case put the case in the oven or a gas grill heat it up to around 350 to 400 degrees then put the bearing in. that way the case is evenly heated when done properly this way the bearing will literally drop in no pressing or driving the bearing in. Have a great week. God Bless!!!
nashguy207 I’ve heard of using an oven but a bbq grill seems like a damn good idea lol. Totally do that next time.
when using a bbq grill i just light half of it and put the case on the that is not lit.
nashguy207 ok yeah, because my parents would never let us put car parts in our oven lol, but the grill would be clear haha
Thanks for watching guys and Happy Memorial Day! Turns out our odyssey is from 1979 and not 1983 like the previous owner thought so it's a 1st gen which is really cool. We were able to find out from the vin number so we’re going to restore it as if it was a first gen so be sure to stay tuned for that!
Build Break Repeat just saying you shoudnt shove a screwdrive inbetween the cases like that because itll ruin the sealing surfaces and you dont have a good seal
Happy Memorial Day. Thank you to all of those who serve our country. This engine is gonna rip!
Build Break Repeat what is the name of your intro song? Btw can't wait for part 2.
kristian woodhouse in the description, but it’s Jimmi by AndrewApplepie
It's a stator not a strator
My first engine rebuild was a two stroke tecumseh for one of my vintage karts. I'm y'alls age, majoring in mechanical engineering this fall. I'd love to meet you guys, ride around. Come to Florida !
Keep up the good work guys, 2 stroke engines are a lot of fun ....and real easy to assemble as u can see. Keep the xlnt content coming, and have fun
I love that kind of 2 stroke... most enjoyable to ride.
Really looking forward to this channel in the future!
Yeah I was RBG red beards garage he’s a. Awesome macanic great to learn from lol!!!
Do y’all watch cars and cameras? There pretty cool to greats vids
Build Break Repeat that’s right y’all gave them a ride in the red truck I watched all those I’m subbed to yalls chanels and I love them vids I’ve watched them all lol
Try heating the whole engine case instead of just heating one spot, it might warp
2nd spark plug hole is for a compression release. Good luck with your build. Hope you don't regret not replacing the rod bearing.
Clint Wood Yeah.....it should be ok, looked perfect at least 🤞🏻, thanks for letting us know about the compression release I’m probably going to order one from an Elsinore because it’s pretty hard to crank over right now with it being bored out and stuff.
good for you guys,,glad to see your not the video king guys,,cheers,
Cant wait to see the first start
Man I love what you guys are doing this is going to be a great build I can see it you guys did a really good job on the motor the only thing I would've done is had a new crank pressed on it is a very crucial part in a two-stroke
Just food for thought. You should have put assembly Lube on that connecting rod pin that connects the piston to the rod. Just for future reference. Plus you didn't put any oil on the head bolts and you were just talking about it. But looking good guys
Good job ... hopp to replace the crankshaft bearing
Looking good guys...
2nd like, you on velocity, right before my b-day!!!
thats a cool motor its set up just like my 340 snowmobile motor that i just put in my buggy build and it screams
Keep up the good work guys
Awesome job guys. You guys are seriously under rated here on TH-cam. Keep up the good work
Awesome thanks
Very impressive i seen your vid on velocity dispatch
do you know if any other style pull cords will work? a three wheeler?
Looks just like the engine out of my own Yamaha blaster I blew that thing up yesterday
Salut. Qu’elle et le diamètre et le pas de ton extracteur d’embrayage ? M 22 ?
Looks brand new now
Next time try pro x pistons wisco has the two small circles and pro xs has better design...I use them..have a blast
Before you go to the heat next time try this: Soak like you did then tighten that jack-bolt as tight a possible.
Grab a 2-3 lb metal dead-blow hammer and give the jack-bolt head a couple of good, square, robust wacks.
99% of the time that will do the trick. Heat can ruin any shaft seals on that motor and air-tight crankcase is a must.
I want one of those motors for my race Kart I like things with pull starts I like simple and power at its lightest possible weight
That's one big oh piston
Nice channel and good content.that head is very similar to the suzuki ts with the dual spark plug.ps i was waiting for the tspe on the inlet to get sucked in when you was yanking it
Me gusta lo que haces tengo un buggy honda Odyssey fl250 y en mi no Ai repuestos saludo amigo
What was the special tool you used in the threaded insert to pull the casing off?
Dope
Buenos motores yo tengo uno.
I have two 1977 fl250s that I just purchased, I'm trying to restore both of them. Where did you guys source all your parts from??
Why are 2 strokes so cool?
What size piston did you get? I have an 83 I just started working on it today thanks to you guys! And I took apart the engine and I’m going to have to bore the cylinder as well due to corrosion but I’m not sure what size piston I should get
Where did you guys get your complete rebuild kit from? I am trying to find one for mine
Where did you get that converter puller
Next time use assembly lube when you're putting the next engine together
hey you're right about Phillips screw heads you're the only one I ever heard say that beside s me
GAP THE PISTON RINGS! There not gapped at the factory, dont want em to catch on a port.
Aaron Blair in 2-strokes you cant put them wrong. Rings cant spin freely because there are little stoppers.
im not speaking of the little pegs the orient the ring. the ends(gap) of the ring need to be filed so that it has the correct radius when the engine is hot. if the ring isnt gapped, when it becomes hot it will expand into the ports and catch, which can ruin the jug. its usually done by putting the ring into the cylinder without the piston and measuring the gap with a feeler gauge.
what's the Honda dirt bike in the background at 4:46 all about?
bryston franke it’s an 84 cr125 we picked up a little while ago, should have a vid out soonish, we have some pics of it on our insta I you wana take a closer look at it.
Do you guys know were i can get a stator for a 79 honda oddesy
When the hell did you guys get on velocity? Watching you guys on there rn ( I know it's a one time thing) but still that's dope
Where did you get the carb kit from ?
Great video guys. How much did you guys spend on the full engine rebuild? Any site you recomend for restoration parts? I bought one for my son but dont know where to start. any info would be greatly appreciated. Thanks
mfuentes8182 oddatv has a lot of parts
If I wasn't going to replace the rod bearing ( I would of though because it most important) make sure you get all,all,all,all the sand out of the motor! You said it was open. Any sand left in the case will ruin the engine in no time at all! I had an 84 250r engine looks pretty much same same!
it looks like the Vintco connecting rod kit is the only way to get this? Do you know if its possible to find just the bearing for the connecting rod?
Why not replace the rod bearings, you already have the cases split lol ? That's the main one to replace hope it holds up tho lol but that has to be the simplest motor ever to rebuild wish they all was like that..
How much is it?. I want one.
Is the fly wheel bolt reverse thread or no?
How did you guys get the top end off??
Does anybody know if i could take my Honda Odyssey 250 and take the engine out and put in a 1994 arctic cat zr 700 engine in it ?
Are all the mounts the same than yes
I just watched your golf cart video and I liked the 2848 shirt and was wondering if you wanted to traid
Trade
what spray paint did you guys you ?
I have a 53cc engine from Powerhouse Generator it 1.3bhp wondering if I can free up some power if I Can Big bore the Exhaust I have the video in my channel FireandGas told me the name of it so I got the Datasheet for it
You probably should have checked the points ignition
What’s going on with the 60 series Toyota Land Cruiser?
stahlke775 It’s my buddy Blake’s. Next time we take the Jeeps wheeling we should be able to get some good footage of it.
Smash the like button dammit.......OH YEAH.......MERICA!!!
Odyssey for life # 1st Comment
Buying a cart in less than a month and need some help guys.
ONE Question.
How much would you pay for a top notch / new / used racing cart with a 5 horse. Low hrs on the engine.
Bigger round style tires.
Ya that's it.
I just need you guys help just to answer this pretty simple question.
michael simard prob $4-500 bucks some are worth more though. We picked up our kt100 kart for $450.
Build Break Repeat 💪🏼👍Thank you dude. 😎
i just bought one for 250 us dlls, it´s the 2nd gen from 1983, no spark...
I'd like to buy this engine
what is your intro music name?
What is your intro song???
Do not paint the jug or head on air cooled engines, Basically anything that has cooling fins.
neo 71665 does it not cool properly or something?
Here comes the straitor xp
3:47 NOOOo..... dont do that. your hurting that poor thing.
You should never put the cases together like that. You need a crankshaft puller to do it properly. Not using a puller will unbalance your crankshaft.
i'm all brand new
Intro song??
Sam Cox It’s in the description, link starts with Andrew apple pie
Build Break Repeat thanks, love the vid btw!
only fouls plugs when you dont send it, sriously
never paint the head
I'm not sure what it is, but the music in your intro creeps me right the fuck out
I love your vids I get so exited when you upload because every video is pure gold.
I'm building a 200cc or 250cc shifter kart, if I have any questions can I ask you because you seem to know a lot. my Instagram is kyle_s.k_norris