assembly...bending cables at 90º etc.Hyper neatness.I congratulate you and thank you.SL2.From Argentina.Buenos Aires.Byee ;) THE TRANSLATION IS ELECTRONIC IT COULD HAVE ERRORS
Can I use 5k resistor instead of 4.7 k resistor and also 1000uf 16v instead of 1000uf 25v? And then can I also use bigger or smaller potentiometer than 10 k potentiometer? Please reply to me.Thanks.
Yes it can be used, but it is very simple design without PWM controlled, I'll soon upload High power motor speed controller based on Pluse width modulation
@@CreativeTechos OUR BAD I CAN WAIT I'LL BE WAITTING ANXIOUSLY, I'VE EVEN BEEN YOUR SUBSCRIBER, WHY WOULD THIS NEW PROJECT OF YOURS RUN A CAR ALTERNATOR? 110 TO ?14 VOLTS
This is simple dimmer circuit in which gate of Mosfet controls both voltage & current from the source to drain, the more positive current it will receive on gate the more it will open to allow the both voltage with current.
If a positive input is applied to the drain input of the N-Channel IRFP450 mosfet, a progressive positive output can be obtained from the source output, is it true
İyi günler, bu uygulamayı koşu bandı motorunda deneyebilir miyim? motor bilgisi modeli 105zyt-1 200v 2,0 hp 3600 rpm 8,5 A . Daha önce 40n60 ıgbt soğutucu ile 500k ohm potansiyometre ayaklarına 320 ohm direnç bağladım . Çıkıştan yük olarak ampulü bağladım çalıştı ama motoru bağladığımda IGBT arıza verdi. Yardım edebilir misin?
How are you brother can I ask a question I know MOSFET He's got three legs 1GATE Signal Input 2 DRAIN output voltage 3Input voltage How did you make the voltage output from SOURCE possible clarification and thank you
It can continuously supply 10A ++ and must have good bigger heatsink, it is basic circuit without PWM. PWM based circuit is more efficient, you can also check out that video too th-cam.com/video/YRoeImb73a8/w-d-xo.html
You are marvelous I tried many of your diys it works perfectly. Thanks
Thanks for watching 😀
Punë të mbarë dhe suksese në tregtimin tuaj
Thanks for watching my friend 🙂
chế mạch điều chỉnh tốc độ rất tuyệt vời 👍👍👏
Thanks for watching 🙂
assembly...bending cables at 90º etc.Hyper neatness.I congratulate you and thank you.SL2.From Argentina.Buenos Aires.Byee ;)
THE TRANSLATION IS ELECTRONIC IT COULD HAVE ERRORS
Thanks for watching 😀
Can I use 5k resistor instead of 4.7 k resistor and also 1000uf 16v instead of 1000uf 25v? And then can I also use bigger or smaller potentiometer than 10 k potentiometer? Please reply to me.Thanks.
Have u made that spot welder as I have told u before 4-5 days ago...by 12-0-12,3 amperes transformer,capacitor,.diodes only
Need to conduct experiments first, I'll try to upload ASAP, please wait patiently.
@@CreativeTechos
Ok
with this circuit I can move a treadmill motor? those used in gyms?
Yes it can be used, but it is very simple design without PWM controlled, I'll soon upload High power motor speed controller based on Pluse width modulation
@@CreativeTechos OUR BAD I CAN WAIT I'LL BE WAITTING ANXIOUSLY, I'VE EVEN BEEN YOUR SUBSCRIBER, WHY WOULD THIS NEW PROJECT OF YOURS RUN A CAR ALTERNATOR? 110 TO ?14 VOLTS
How many volts motor is that? Is it ac or dc?
@@CreativeTechos friend is a 94 volt treadmill motor
Got it 94v dc right?
Great work
Thanks for watching 😀
Thanks bro . muchas gracias
Muito bom ok 🔝
Congratulations! I liked the whim in the assembly of the circuit. Can the IRFZ44N Mosfet be used instead? Would be the same connections? Thank you
Could be used but resistor values might change
Creative video, thanks :)
My pleasure Thanks for watching 😀
can it handle 125v dc10a for treadmill?
what is the method that was used to control the speed ?
is it voltage regulation ?
Mosfet controls voltage + current through potentiometer on gate
what is the maximum output ? is it 24v? if we give input 12V 2A?
Can i control 1 to 12 volt input voltage from this circuit?
And Max kitna Amp control ho sakta hai?
Yes of course you can control
In this circuit we see voltage is loss but ampier will loss also? Pls. guide us.
This is simple dimmer circuit in which gate of Mosfet controls both voltage & current from the source to drain, the more positive current it will receive on gate the more it will open to allow the both voltage with current.
Thanks sir
My pleasure Thanks for watching 😀
@@CreativeTechos One question more sir. Pls reply input maximum voltage & ampier value.
It should be around 24v max with 10A
Can this electronic circuit bear the load of a 5 amp 12 volt motor?
Yes absolutely, good heatsink should be installed as this is basic circuit, You can also find PWM controlled motor circuit on my channel
Thanks for sharing
My pleasure 😀, Thanks for watching
can I use a 5k potentiometer?
Yes, you can use 5K potentiometer
If a positive input is applied to the drain input of the N-Channel IRFP450 mosfet, a progressive positive output can be obtained from the source output, is it true
Yes, it can be done but also connect 220R resistor from positive to gate.
@@CreativeTechos Thank you
My pleasure Thanks for watching 🙂
can i use any mosfet
Yes Any N channel MOSFET can be used
Can use for motor DC 12volt 65ampere and input supply battery 12volt 65ampere?
Yes, but use good bigger size of heatsink
@@CreativeTechos if there is no IRFP450 transistor, is it possible to use another type of transistor?
Ist of all it is not transistor, it is N channel MOSFET, you can use 2x Mosfets in parallel of irfz44n, 3205 etc.
@@CreativeTechos cuánto amp soporta
@Fransisko New PWM Motor Control circuit, recommended for you
Is it possible to work with 36 volt big motor
Bhai 36v high amp electric cycle controller banao pls 🙏
I'll try to upload ASAP, Thanks for watching 🙂
İyi günler, bu uygulamayı koşu bandı motorunda deneyebilir miyim? motor bilgisi modeli 105zyt-1 200v 2,0 hp 3600 rpm 8,5 A . Daha önce 40n60 ıgbt soğutucu ile 500k ohm potansiyometre ayaklarına 320 ohm direnç bağladım . Çıkıştan yük olarak ampulü bağladım çalıştı ama motoru bağladığımda IGBT arıza verdi. Yardım edebilir misin?
Tell me about maximum input volt. For this dimmer input
will it work on 12 volt 95ah battery?
Yes, absolutely it will work.
The best
Thanks for watching 😀
Super
Bu devre çok verimsiz
What is the function of capacitor ?
How are you brother can I ask a question I know MOSFET He's got three legs 1GATE Signal Input
2 DRAIN output voltage
3Input voltage
How did you make the voltage output from SOURCE possible clarification and thank you
Is the diode on your mosfet upside down?😀 at 4 min 31 sec.
It is a flyback diode
What is the capacitor for please
I can use it dc fan for bus seat fan
Can I use 24v battery and 1000w motor.
will burn out if u mash 1000w thru that
How many amps will it pass ?
It can continuously supply 10A ++ and must have good bigger heatsink, it is basic circuit without PWM.
PWM based circuit is more efficient, you can also check out that video too
th-cam.com/video/YRoeImb73a8/w-d-xo.html
Maximum Amper
Minimum volts
Plz explain
Do you have circuits of voltage regulator 48 to 12 volt about 15a
Yes, I'll try to upload ASAP
Berapakah arus maximal untuk proyek ini
necesito hacer un circuito para un motor de una caminadora
🔝🔝👌
I need a controller that drives a homemade brushless motor
How to increase current and voltage rating??
Suppose to how much?
How to control a 220VDC 700w motor?
motor 48v 1200w
Chota motor nahi bada motor dikhao
the motor dotnot image😠
no me funciono
Byuñisimo😂
Slot diginose bib
Card on GPU VAG
UVLSI
GPU
Ic intrageted circuit
7