Just curious if you’ve checked the gasket on your 3rd brake light to make sure it’s not deteriorating? They have a high failure rate on these trucks and allow water to get inside the cab. Also, the seal around your sliding back window can crack and will leak water down right where your amp is located. And if you have vents in the back panel of the cab they too can let water in and could potentially short out your whole setup! Just a friendly heads up from a fellow Ram owner ✌️
It goes pretty easily. Just be careful cutting so you dont hit the seats and try to leave a little of the white plastic if possible, otherwise it may rattle a tad and then you just have to put a little electrical tape around the metal to get that to stop. Its easy though.
The other seat i got rid of too much of the white plastic compared to the one i showed in the video. So it made noise if you pulled it forward and back. All i did was put some electrical tape around the bracket i cut (shown in video) and then that went away. (Easy fix)
That plastic ends up breaking over time anyways. I just remove it and then put some 5/16" fuel hose with a couple zip ties on the bar hoop on the back of the cab. you might have to trim a little more of the bottom of the metal tab on the seat to clear the fuel hose, but just go slow until it just clears and you'll have plenty still grabbing when the back drops back down. and no rattling! I started with the electrical tape...but it wears out pretty quickly from driving and operating the seat.
When you have the base of the seat folded all the way up, do they still stay in the up position locked like original also after this mod? Or will they fall forward when folded all the way up? Thank you!
@@coverado Hi, thank you for reaching out and thanks for the offer but Im going to have to pass. My truck already has leather seats that are heated and cooled, adding something over the top of that would defeat the purpose. Thanks again for reaching out though.
It worked buddy I have the full back bench seat and did exactly what you did and I now have a storage area! I also had to cut the plastic off. It's got movement now, hopefully it doesn't clunk to bad
@@dirtsailoroff-road5580 it does have a rattle on like washboard roads. I wrapped the hooks on the seat. Thinking wrapping the loops on the back of the cab would be better.
THANK YOU!!!! Everyone showing off flipping it down, thanks for sharing the process. I’ve just been pulling only seat back trying to get it come down
Welcome! I'm glad it helped out.
Doing this tomorrow. Thanks brother!!
Welcome! Glad to help!
Just curious if you’ve checked the gasket on your 3rd brake light to make sure it’s not deteriorating? They have a high failure rate on these trucks and allow water to get inside the cab. Also, the seal around your sliding back window can crack and will leak water down right where your amp is located. And if you have vents in the back panel of the cab they too can let water in and could potentially short out your whole setup! Just a friendly heads up from a fellow Ram owner ✌️
I used 3/4 in MDF. 16.5" by 2". Used it as a spacer
Thanks bud got a 2020 warlock same problem tackling tomorrow morning
It goes pretty easily. Just be careful cutting so you dont hit the seats and try to leave a little of the white plastic if possible, otherwise it may rattle a tad and then you just have to put a little electrical tape around the metal to get that to stop. Its easy though.
The other seat i got rid of too much of the white plastic compared to the one i showed in the video. So it made noise if you pulled it forward and back. All i did was put some electrical tape around the bracket i cut (shown in video) and then that went away. (Easy fix)
For anybody watching. At the bottom of the plastic after you cut the metal and plastic. Cut a bit off at a 45° angle, the plastic won't get caught
How’d it go with your 2020 warlock? I have a 22 and my seats don’t tilt up when you raise the bench… wonder if this will not work on the 5th gens
When it’s fold up doe the seat fall down when you break?
You mean BRAKE?
That plastic ends up breaking over time anyways. I just remove it and then put some 5/16" fuel hose with a couple zip ties on the bar hoop on the back of the cab. you might have to trim a little more of the bottom of the metal tab on the seat to clear the fuel hose, but just go slow until it just clears and you'll have plenty still grabbing when the back drops back down. and no rattling! I started with the electrical tape...but it wears out pretty quickly from driving and operating the seat.
Good idea
Does it rattle or make noise when driving on bad or washboard roads now?
@@dirtsailoroff-road5580 Nope, not at all
When you have the base of the seat folded all the way up, do they still stay in the up position locked like original also after this mod? Or will they fall forward when folded all the way up? Thank you!
i just did mine and the seat stay locked in when fully up, just like norma;
Hello. This is Cherry from Coverado. Are you interested in working with us to try our Ram custom seat covers and help us make a video?
@@coverado Hi, thank you for reaching out and thanks for the offer but Im going to have to pass. My truck already has leather seats that are heated and cooled, adding something over the top of that would defeat the purpose. Thanks again for reaching out though.
@@Temptation_Offroad No problem! I hope that we can collaborate in the future.
Yup doing this today. I have 2 subs under the seat i need a spot for a rifle...
It worked buddy I have the full back bench seat and did exactly what you did and I now have a storage area! I also had to cut the plastic off. It's got movement now, hopefully it doesn't clunk to bad
@@4g63tpowered Does it make noise? I'm considering this but don't want it to be annoying lol
@@dirtsailoroff-road5580 it does have a rattle on like washboard roads. I wrapped the hooks on the seat. Thinking wrapping the loops on the back of the cab would be better.
Damn bud you seem out of breath lol.
@@bg31282 Yeah, working on getting back in shape. Hit the weight room for 3hrs yesterday!