Hi, sir My forklift don't start in the ignition switch and hydrauliic system don't work . I connect directely the postif of starter with the excitor it runs the engine but the hydraulic system don't work . When i make chunt in the starter relay . It runs also but the hydraulique system don't work
Hi sir! Good day. Our forklift has an error. We change the battery then when we start it error codes pop ups *OFF HYD-LEVER TO NEUTRAL * whats the problem with that. Hope you help us. Thank you in advance
Forklift Lift r not use proply. I have up in lift but limit switch r not work proply. Screen show 4:1 .wts a prblm. And how to change micro switch. Send me a vedio plz
I have RR B3 reach truck error E107 occurs after some working with reach truck. Anybody tell me what is the problem. I have replaced the battery but same condition
The main contactor K10 does not close during truck start up and the emergency stop switch does not operate 1, defective k10 contactor tips 2, defective a5 card Check voltage at pin 808 on a5 card voltage must be battery voltage on start up. If no voltage check fuse f62 (10amp) If fuse is ok check contactor tips,
@@marclawson3453 it's due to battery. Battery is weak. I have also replaced the MCU. After replacing reach speed issue occurs then I have done calibration. Machine doing it's all functions good. But after some days reach speed problem again occurs. Can you please share with me why this is happening?
@@akmmechatronics5690 what do u mean by mcu? If the battery is faulty then it will cause the contact tips to arc and burn out. Check the contactor under the seat and see if there is any burn marks. Contractors are cheap and I could probably get u the part no, don’t understand why u are changing computers before trying this
@@akmmechatronics5690 remove the floor plate and check the spring under the brake pedal, the spring snaps and it will throw a fault code and cause the reach to go in and out slow, I think it’s parameter 38 or 28 u need to go into to calibrate it, fault will keep appearing if the spring is broken tho
@@marclawson3453 yes you are right. Some time error 16 and 17 occurs. It's due to break and accelerator press. Can you please share your whatsapp number?
Thank you for these videos!
Hi, sir
My forklift don't start in the ignition switch and hydrauliic system don't work .
I connect directely the postif of starter with the excitor it runs the engine but the hydraulic system don't work .
When i make chunt in the starter relay . It runs also but the hydraulique system don't work
Thanks you sir very very nice knowledgeable video ok
How would I get a wiring schematic for a reach truck I'm trying to repair?
Nice sir, so informative, galing ,more video poh salamat
Thanks for your time...where do you get your wiring diagrams thank you againg.
Most of them are provided by the company. Some I bought online. Too expensive from dealerships.
Thanks Where can I find the circuit diagram for this lever? electrical diagram
Either you buy it online or from the dealer
nice content
Nice job, sometimes the smallest parts can cause what seem to be the biggest problems.
Very smart way to solve problems.
One question, where did you find the resistors ? I mean in what part of the lift truck
Left hand side of the battery compartment.
ForkliftGeek thank you !!
CAT 966H wheel loader problem in lift cylinder not working I need to help with me
Hi, what do you check when toyota tonero forks dont stay when you lift. They just drop down slowly when not using the controls???
Either the cylinder or the control valve is internally leaking.
Hi sir! Good day. Our forklift has an error. We change the battery then when we start it error codes pop ups *OFF HYD-LEVER TO NEUTRAL * whats the problem with that. Hope you help us. Thank you in advance
Forklift Lift r not use proply. I have up in lift but limit switch r not work proply. Screen show 4:1 .wts a prblm. And how to change micro switch. Send me a vedio plz
sir how about toyota diesel engine only lift up function lift down no function?
Then I would check if there is a mechanical binding in the mast, cylinders. If none then it would have to be in valve bank.
@@forkliftgeek10 thanks highly appreciated
Good 👌👌👌👌
please could anyone give some tips why machine doesn't lift up!
charger is good
I have RR B3 reach truck error E107 occurs after some working with reach truck. Anybody tell me what is the problem. I have replaced the battery but same condition
The main contactor K10 does not close during truck start up and the emergency stop switch does not operate
1, defective k10 contactor tips
2, defective a5 card
Check voltage at pin 808 on a5 card voltage must be battery voltage on start up.
If no voltage check fuse f62 (10amp)
If fuse is ok check contactor tips,
@@marclawson3453 it's due to battery. Battery is weak. I have also replaced the MCU. After replacing reach speed issue occurs then I have done calibration. Machine doing it's all functions good. But after some days reach speed problem again occurs. Can you please share with me why this is happening?
@@akmmechatronics5690 what do u mean by mcu? If the battery is faulty then it will cause the contact tips to arc and burn out. Check the contactor under the seat and see if there is any burn marks. Contractors are cheap and I could probably get u the part no, don’t understand why u are changing computers before trying this
@@akmmechatronics5690 remove the floor plate and check the spring under the brake pedal, the spring snaps and it will throw a fault code and cause the reach to go in and out slow, I think it’s parameter 38 or 28 u need to go into to calibrate it, fault will keep appearing if the spring is broken tho
@@marclawson3453 yes you are right. Some time error 16 and 17 occurs. It's due to break and accelerator press. Can you please share your whatsapp number?
ECU Fuse! 😅🤣😅🤣😅🤣
Aur clip current problem Sar Hindi mein banae video