AMD Sapphire Pulse Radeon RX 580 4GB|Cleaning,Changing Thermal Paste,Pads|Disassembly,Tear Down
ฝัง
- เผยแพร่เมื่อ 12 ก.ย. 2024
- -If you have any questions or any advices write them down in the comments!
-If you enjoyed the video a like will be apreciated!
Music • BGM | VLOG | No.12 In ...
-Intro Made By: VipexArtz
-VipexArtz`s channel: / vipexartzoriginal
-Outro Animation: • Rounded Neon Multicolo...
-See you in the next one!
-PC Specs:
-CPU: intel Core i3 10100F
-Cooler: Arctic Freezer 34 eSports DUO
-GPU: AMD Sapphire Pulse Radeon RX 580 4GB
-RAM: Patriot Viper Steel 16GB(2x8) 3000MHz (Using them at 2666MHz,because of the motherboard)
-CASE: Lian Li O11 Air Mini
-PSU: be quiet! System Power 9 500W
-MOBO: MSI H510M-A PRO
-SSD: ADATA Swordfish 250GB
-SSD: Sillicon Power A55 256GB
Perfect music choice! Thanks :)
Isopropilic alcohol is what you need for cleaning the thermal paste faster, good video, btw
Thank you,i used isopropyl alcohol,but the paste was really old,dry and stuck.
@@ryzeeboi7637 use Zippo fuel to soften the old thermal paste. put a kitchenpaper on the Die and keep it wet for 10 minutes. then use cotton tips to clean.
i use WD40 contact cleaner is good as well
Bruh, cleaning that case just put in the water, not include fan. And dry in 1 day
Many thanks for this video!!!
You are welcome!
@@ryzeeboi7637 Thank you aswell. A lot of used cards enter secound hand market and this was perfect for fixing thermals. By the way did it improve efficiency for you?
No,the efficiency didn’t change.
Asmr level of enjoying 😊
Thanks, i got the same GPU from a miner and it wasn't working. Cleaned it up and reapplied paste n it started working again.
same situation, what problems did u have? mine is crashing in furmark reaching 86celsius and also crashing while exporting in premiere with fans spinning at max and losing signal
mine just wouldn't boot man no clue what the problem might be for you @@adrian3126
May gpu is rx580 may problem is overhear 81 to 82c
This morning I opened overwatch 2 and I got an alarming 82 degress in lobby
So I opened the card changed the thermal paste and now I'm not surpassing 61 degress
I'm happy
0.5 thermal pad is too thin, there will be no connection between the chip and the cooler. I recommend using 1mm from Artic. This thermal pad is softer than the original, so you don't have to worry about 1mm thickness. A comfortable squeeze will occur.
Wrong, terrible advice. Many cases of crashing on TH-cam by using 1mm on Saphire RX 500 cards (their stock pads are 0.75mm from fabric). Do not use 1mm on these cards it will not squish enough for the heatsink to make proper contact with the processor. 0.5mm does the job here.
bro added thermal pads to the capacitors instead of vrms. big fail brother
sir, im from Philippines. do you have idea what size of Spring Screws that mount in case and back plate? is it m2*6 or m2*8?
Sir sapphire pulse rx580 uses 0.75mm for VRam and 1.0mm for VRM right? Its hard to find 0.75mm for VRam. Did you use 0.5mm for VRam? How about VRM did you use 1.0mm?
I used only 0.5mm.
That's what I did, until the VRAM chips overheated and produced artifacts. Can't even run 4K benchmarks in superposition without it crashing the program. I now use thermal putty instead, which lowered temps more than previously. The only caveat is that it's a mess to clean.
@@ryzeeboi7637 im use 0.5mm for vram but did not have contact to heat sink. officially shapphire use 0.75mm but they say its safe to use 0.5mm
what was the GPU you used the 0.5mm pads on?
Can the Radeon RX 580 take any video source IN through its HDMI or displayport ? Or are they only outputs ? Thank you
DVI-D port,two HDMI ports and two DisplayPorts
Output only. You would need a dedicated capture card if you want to capture any footage that isn't generated by the GPU.
before and after temperature?
Before was 85 degrees and after was 70.
@@ryzeeboi7637same,I will do it
I need to change the pads to an rx580 8gb sapphire, which one does it have specifically?
Try 0.5mm, 1.0 thermal pads are too thick according to online sources
@@tanja-k thx
@@tanja-k could I get away with only using thermal paste instead of pads in a pinch?
You can, but I don’t recommend it, because it will make a mess and will be not that effective probably.
I used 0.5 mm pads.
hows the gpu now?
is a 1mm thermal pad too thick for this gpu?
Yes. Ive seen many cases of crashing by using 1.0mm on Saphire RX 500 séries. Use 0.5mm thermal pads If needed.
What temperature is danger for this card?
100-110 like every gpz. For everyday use dont get over 85
@@L4ftyOne ok thanks
I recommend 70°C
willl opening cause warranty void
Прокладки не на дросселя надо устанавливать, а на микросхемы DC-DC ШИМ(PWM) микросхемы!!!!
my rx 580 runs at around 86-88 degrees is that normal or is that bad
Is bad check you thermal paste, fan, and airflow.
At full load not ideal, too high. If thats the temperature at idle, then something is very wrong.
@@hayemiranda7647 at full load and the fan is hella loud like 3200 rpm and 85 degrees but I have this like msi version or something and it's known to be loud and hot 🔥🥵 so I think I'm good cuz a lot of people used it like that for couple of years
you wrong put vrm thermal pad
what thermal pad thickness should be use 0.5mm?
Yes,0.5mm.
when i remove the heatsink cover that metal bar part comes over it how can i put it back on pcb board? i temporary put thermal paste on it to prevent over heating issues thou
@@ryzeeboi7637 also for the 8gb version?
Nah, 0.5mm won't make contact at all for this model. The person from the video made a huge mistake. 1.0mm is a way to go.
@@zeljkorilke701i have problem with 1 mm, i will try 0.5 mm
can you share the bios? my bios corrupted
toо much paste